Instruction/ maintenance manual of the product CAM325 Advent
Go to page of 11
Model: CAM325 Wired Bumper or Butte rfly Mounted Camera Inst allation Manual Features • Very Small Compact Camera • High Resolution, ¼ inch CMOS Color Camera • Waterproof Housing • 160 Degree Wide View Angle • Selectable Image: Normal/Reverse • Multiple Camera Mounts including Flush bumper mount and adjustable butterfly mount.
2 T able of Content s Warnings ...................................................................................... 3 Product Description ..................................................................... 4 Packing List ..........................
3 W arnings The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations.
4 Product Description This new camera system gives you two mounting options for installing a backup camera onto the rear of your vehi cle (surface butterfly mount and in bumper flush m ount). This Wired Camera is compatible with m o st monitors/TFT screens and can be connected using a standard RCA connector.
5 Camera Inst allation Butterfly Mounting Instructions 1. Assemble the camera – ensure that the top of the camera marked with an alignment arrow and the word “U P” is aligned with the notch in the metal bracket. 2. Decide on a suitable mounting position.
6 d) Drill a 5/8 inch hole at the se lected location. e) Coat the edge of the hole with rust preventative. f) Route the camera cable through the grommet and then through the hole. g) Insert the grommet in the hole to keep water from entering the vehicle.
7 Wiring the Camera to the Vehicle’s Reverse Lamp 1. Locate the reverse lamp in the tail light assembly. 2. Using the tap connector supplied, perform the following steps: a) Place the un-stripped positive lead from the tail lamp in the run channel, which runs completely through the connector.
8 Reverse/Normal Image Adjustment The camera comes standard with a reversed i mage, designed for mounting at the rear of the vehicle. If you need to change to a forward or normal image view, clip the blue jumper wire loop on the wiring cable to change the camera image to normal.
9 S pecifications 1. Voltage: DC9v – DC24v 2. Current: 50 mA 3. Signal System: NTSC 4. Image Sensor: ¼” CMOS Sensor 5. Horizontal Resolution: 480 lines 6. Viewing Angle: 160 degrees 7. Minimum Illum ination: 0.7 Lux 8. Image Display: Selectable Nor mal/Reverse Image 9.
7.
8 © 2008 Audiovox Electr onics Corp., 150 Marcus Blvd. , Hauppauge, N.Y. 11788.
An important point after buying a device Advent CAM325 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Advent CAM325 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Advent CAM325 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Advent CAM325 you will learn all the available features of the product, as well as information on its operation. The information that you get Advent CAM325 will certainly help you make a decision on the purchase.
If you already are a holder of Advent CAM325, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Advent CAM325.
However, one of the most important roles played by the user manual is to help in solving problems with Advent CAM325. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Advent CAM325 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
