Instruction/ maintenance manual of the product IPPC-9151 Series Advantech
Go to page of 114
IPPC-9151 Series Rugged Industrial Panel PC with Intel® Pentium® 4 or Celeron® and 15" LCD Display Users Manual.
IPPC-9151 Series Users Manual ii Copyright notice This document is copyright ed 2005, by Advantech Co . Ltd. All rights are reserved. Advantech Co., Ltd.
iii FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection ag ainst harmful interference when the equipment is operated in a commercial environ- ment.
IPPC-9151 Series Users Manual iv Packing List Before setting up the system, check that the item is among those listed below and is in good condition . If your Panel PC does not match any of those below, please contact your dealer immediately.
v IPPC-9151F-XAE Rugged Pentium 4 Industrial Panel PC with 15" LC D,180W AC power supply, Stainless steel chassis and flat-sealed aluminum front panel IPPC-9151F-RAE IPPC-9151F-XAE with resistive touchscreen Additional Information and Assistance Step 1.
IPPC-9151 Series Users Manual vi S a f e t y I n s t r u c t i o n s 1. Read these saf ety inst ructions careful ly. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.
vii W i c h t i g e S i c h e r h e i s h i n w e i s e 1. Bitte lesen sie Sich die se Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den sp äteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerä t vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger.
IPPC-9151 Series Users Manual viii Der arbeitsplatzbezogene Schalldruckpeg el nach DIN 45 635 Teil 1000 beträgt 70dB(A) oder weiger. Haftungsausschluss: Die Bedien ungsanleitungen wurden entsprechend der IEC-704-1 erstellt. Adv antech lehnt jegliche Verantwortu ng für die Richtigkeit der in diesem Zusamm enhang getätigten Aussagen ab.
ix Contents Chapter 1 General Information ........................................ 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ ........... .............. ............
IPPC-9151 Series Users Manual x Table 3.1:Jumpers, switches a nd their functions .......... 21 3.1.3 Jumpe r Locations ... ............. ........... ............ ............. ...... 21 Figure 3.1:Jumpers on the IPPC-9151 motherboard .... 21 3.1.4 Conne ctors .
xi 8.3 Installing Driver for Wind ows 2000/XP ........ ........... ...... 47 8.4 Configuring PenMount Window s 2000/XP Driver ......... 52 8.4.1 Pe nMount Control Panel ..... .............. ........... ........... .... 52 8.4.2 Pen Mount Monitor Menu Icon .
IPPC-9151 Series Users Manual xii Table B.7:Internal speaker c onnector (CN1 5) ............ 102 B.8 IR connector (CN24) ..................... .............. ........... ....... 102 Table B.8:IR connector (CN24).............. ........... ......... 102 B.
CHAPTER 1 General Information This chapter gives background information on the IPPC-9 151 series Sections include: • Introduction • Specifications • Dimensions.
IPPC-9151 Series Users Manual 2 Chapter 1 General Information 1.1 Introduction The IPPC-9151 seriesof industrial pane l PCs is especially designed to fit in space-limited environm ents where expansion is restricted. Its solid structure enables systems to operate under harsh industrial conditions.
3 Chapter 1 1.2 Specifications 1.2.1 General • Dimension s (W x H x D): Front Panel: 428 x 310 x 8 mm (16.85" x 12.2" x 0.31") Cabinet: 402 x 290 x 162 mm (15.82" x 11.41"x 6.3 7") Cut out dimension: 406 x 294 mm (15.98" x 11.
IPPC-9151 Series Users Manual 4 • Serial ports: Two serial ports with one RS-232 port (COM1 ) and one RS-232/422/ 485 port (COM2). Both ports are compatible with 16C550 UARTs • Universal serial bus (USB) port: Supports up to 4 USB (version 2.0) ports.
5 Chapter 1 1.2.5 PCI bus Ethernet Interface • Chipset: Intel RC8254 0Em local bus. • Ethernet Interface: Fully complies with IEEE 802.3u 100Base-T and 10 Base-T specifica- tions. Includes software drivers and boot ROM • 100/10Base-T auto-sensing capability 1.
IPPC-9151 Series Users Manual 6 1.3 Dimensions Figure 1.1: IPPC-9151FA Dimensions Figure 1.2: IPPC-9151GA Dimensions 1 7 ” 1 7 ”.
CHAPTER 2 System Setup This chapter details system setup for the IPPC-9151 Series. Sections include: • General • Installing SDRAM • Installing a CPU • Installing a 2.
IPPC-9151 Series Users Manual 8 Chapter 2 System Setup 2.1 A Quick Tour of IPPC-9151 Before you start the computer, please follow these procedures to set up the system. 1. Check and adjust jumpers on the motherboard (see Chapter 3) 2. Install SDRAM 3.
9 Chapter 2 Figure 2.1: Side View Figure 2.2: Bottom View • • • •.
IPPC-9151 Series Users Manual 10 2.1.1 PS/2 Mouse and Keyboard If you wish to use a full-size d esktop keyboard and PS/2 m ouse with your panel PC, follow these instructio ns: 1. Be sure the panel PC is turned off. 2. Attach the keyboard adapter to the 5-pin green port on the rear bott om side of the rear cover.
11 Chapter 2 2.1.4 Serial COM ports There are two serial COM ports on the bottom of the rear cover. You can easily attach a serial devi ce to the panel PC, such as an external modem or mouse. Follow these instructions: 1. Make sure the panel PC and any other peripherial devices you may have connected to the panel PC are turned off.
IPPC-9151 Series Users Manual 12 2.1.7 Ethernet To install Ethernet for your system: 1. Connect the Ethernet cable. 2. Turn on the panel PC. 3. Under DOS, run IPPC-9151LA NRSET8139.EXE to check hard- ware network status before install ing the Ethernet driver.
13 Chapter 2 2.2 Installing SDRAM You can install from 64 MB to 2 GB (x2) of DDR SDRAM memory. The Panel PC system provides one 184-pin DIMM (Double Inline Memo ry Module) socket, and supports 2.5 V DDR SDRAM. 1. Unlock the back cover and open it. 2. Disconnect the FDD and CD-ROM cable.
IPPC-9151 Series Users Manual 14 4. Disconnect the HDD cable. 5. Undo the seven screws of the HDD Module so you can install the SDRAM..
15 Chapter 2 6. Push the two white eject levers on each side of the DIMM outward until they are separated from the black vertical posts. 7. Insert the memory module into th e socket at an angle of 90 degrees. 8. Push the two eject levers toward the vertical posts at each end of the socket until the module is upri ght.
IPPC-9151 Series Users Manual 16 2.4 Installing a 3.5" HDD You can attach one enhanced Integr ated Device Electronics (IDE) hard disk drive to IPPC-9151's internal controller which uses PCI local bus interface. The following instru ctions are for installation: 1.
17 Chapter 2 6. Insert the FDD, CD-ROM Module and fix the back cover..
IPPC-9151 Series Users Manual 18 2.5 Installing Add-on Cards This system supports two PCI expansion cards. 1. Detach the five screws on the back to open the lid. 2. Take away the slot bracket. 3. Insert the add-on card, and put on the lid. 2.6 Mounting Instructions There are two ways to mount the system: panel mounting or rack mount- ing.
CHAPTER 3 Jumper Settings and Connectors This chapter tells how to set up the panel PC hardwa re, including in struc- tions on setting jumpers and conn ecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installat ion proce- dures.
PPC-154 User’s Manual 20 Chapter 3 Jumper Settings & Connectors 3.1 Jumpers and Connectors 3.1.1 Setting jumpers You can configure your panel PC to match the needs of your application by setting jumpers. A jumper is the sim plest kind of electrical switch.
21 Chapter 3 3.1.2 Jumpers and switches The motherboard of the IPPC-9151 has a numb er of jumpers that allow you to configure yo ur system to suit yo ur applications. The table below lists the function of each of the board’s jumpers. 3.1.3 Jumper Locations Figure 3.
PPC-154 User’s Manual 22 3.1.4 Connectors Onboard connectors link the panel PC to external devices such as hard disk drives or floppy drives. The table below lists the function of each of the board’s connectors.
23 Chapter 3 3.1.5 Locating connectors Figure 3.2: Connectors on IPPC-9151 motherboard.
PPC-154 User’s Manual 24 3.2 CPU Installation You can install an Intel Pen tium 4 or Celeron CPU without setting any frequency ratio or voltage. *Default setting 3.3 CMOS Clear for External RTC (JP3) This jumper is used to erase CMOS data and reset system BIOS informa- tion.
25 Chapter 3 3.4 COM-port in terface (JP4, JP5) The panel PC provides two serial ports. COM1 (RS-232) and COM2 (RS- 232/422/485) in one COM port co nnector. 3.4.1 COM2 RS-232/422/485 setting (JP4) COM2 can be config ured to operate in RS-2 32, RS-422, or RS-485 mode.
PPC-154 User’s Manual 26 3.5 VGA interface The panel PC's AGP VGA interface can drive conventional CRT dis- plays. It is also capable of driving a wide range of flat panel displays, including electroluminescent (EL), gas plasma, passive LCD and active LCD displays .
CHAPTER 4 Intel Chipset This chapter provides i nformation on the Intel chipset configuration. Sections include: • Introduction • Installation of chipset driv er for Windows 98/NT/ME/200 0/XP • .
IPPC-9151 Series Users Manual 28 Chapter 4 Intel Chipset 4.1 Introduction IPPC-9151 uses the 845GV chipset from Intel., with buil t-in high perfor- mance 2D/3D Intel Extreme Graphics 2, flexibl e 100/133MHz system bus settings, supp ort for DDR266 SDRA M and multiple power sav ing modes.
29 Chapter 4 4.2.1 Installation for Windows 98/NT/ME/2000/XP 1. a. Select "Start", "Run”. b. Enter the driv er path "D:IPPC-9151 G& 9171G_DRV&Utili ty Chipset SoftwareIAA Dri ver2.3iaa23_multi.exe". c. Click “OK”.
IPPC-9151 Series Users Manual 30 4.3 Further Information For further information about the AGP/VGA installation in yo ur IPPC- 9151, includi ng driver updates, tro ubleshooti ng guides and FAQ lists, visit the following web resources: Intel website: www.
CHAPTER 5 PCI Bus Ethernet Inter- face This chapter provides i nformation on Ethernet configuratio n. Sections include: • Introduction • Installati on of Ether net Driver for Windows 98/NT/ME/2000.
IPPC-9151 Series Users Manual 32 Chapter 5 PCI Bus Ethernet Interface 5.1 Introduction The IPPC-9151series is equipped with a hig h performance 32-bit Ether- net chipset, which is fully complian t with IEEE 802.3 100 Mbps CSMA/ CD standards. It is supported by major network operating systems, and is also both 100Base-T a nd 10Base-T compatibl e.
33 Chapter 5 5.2.1 Installation for Windows 98/NT/ME/2000 1. a. Select "Start", "Run" b. Enter the path, "D:IPPC-9151G& 9171 G_DRV&Utility Intel Lan 6.2Set up.exe" c. Click "OK" 2. a. Click "Next” 3.
IPPC-9151 Series Users Manual 34 4. a. Click "Next" 5. a. Click "In stall".
35 Chapter 5 6. a. Click "Finish" 5.3 Further Information Intel websit e: www.intel.com Advantech website: www.advantech.com.
IPPC-9151 Series Users Manual 36.
2 CHAPTER 6 VGA Setup This chapter provides i nformation on the VGA setup. Sections include: • Introduction • Installation of VGA Drivers - for Windows 98/2000/M E - for Windows NT - for Windows X.
IPPC-9151 Series Users Manual 38 Chapter 6 VGA Setup 6.1 Introduction The IPPC-9151 has an onboard AGP fl at panel/VGA interface. The spec- ifications and features are described as follows: 6.1.1 Chipset IPPC-9151 uses a 845G chipset from Intel for its controller.
39 Chapter 6 6.2 Installation of the VGA Driver Complete the following steps to install the VGA driver. Follow the proce- dures in the flow chart that apply to the operating system that you are using within your IPPC-9151. 6.2.1 Installation for Windows 95/98/ME 1.
IPPC-9151 Series Users Manual 40 3. Read the license agreement and click "Yes" if you accept the terms and wish to continue. 4. The driver files will now be inst alled. When the install finishes, choose the "Yes." option to restar t, and click "Finish" to restart your computer.
CHAPTER 7 Audio Setup This chapter provides i nformation on the Audio setup. Sections include: • Introduction • Installati on of Audio Driver - for Windows 98/2000/M E - for Windows NT - for Windo.
IPPC-9151 Series Users Manual 42 Chapter 7 Audio Setup 7.1 Introduction The IPPC-9151's on-board audio inte rface provides high -quality stereo sound and FM musi c synthesis (ESFM) by using the V IA VT82C686 audio controller from VIA. The audi o interface can record, compress, and play back voice, sound, and music with built -in mixer control.
43 Chapter 7 7.2.1 Installation for Windows 98/ME/2000/XP 1. a. Select "Start", "Run" b. Enter the path "D:IPPC-9151G& 9171G_DRV&Utilit y ALC202WinX P_2K_Me_9XSetup.
IPPC-9151 Series Users Manual 44.
2 CHAPTER 8 Touchscreen This chapter contai ns informati on on the touchscreen, its installation and configuration..
IPPC-9151 Series Users Manual 46 Chapter 8 Touchscreen 8.1 Introduction The IPPC-9151 Seri es’ optional touchscreen u ses advanced 8-wire resis- tive technology.
47 Appendix 8 • Visible light transmission: 75% typical (>74% @ 550 nm test) • Clarity: Clear Finish - 25%, Antiglare Finish - 15% Sensor board • Chemical strengthened glass with 4 H hardness stand ard.
IPPC-9151 Series Users Manual 48 You must also have one of the foll owing PenMount Serial Interface con- troller boards installed: 90A4, 90 26B, 9036 or 9084. Contents of the Pen- Mount Windows 2000/XP dri ver folder are listed below. DMC9000.inf DMC9000.
49 Appendix 8 2. Insert the PenMount Driver CD-ROM. Go to the Windows 2000- XP Driver folder. Click setup.exe . 3. The screen displays the inst allation wizard for the PenMount soft- ware.
IPPC-9151 Series Users Manual 50 4. A License Agreement appears. Click “I accept…” and “Next” 5. The “Ready to Install the Program” screen appears.
51 Appendix 8 6. The next screen is “Hardware In stallation.” Select “Continue Any- way.” 7. The “InstallShield Wizard Comple ted” appears.
IPPC-9151 Series Users Manual 52 8.4 Configuring PenMount Windows 2000/XP Driver Upon rebooting, the computer aut omatically finds the new 9000 control- ler board. The touch screen is connected but not calibrated . Follow the procedures b elow to carry out calibration.
53 Appendix 8 NOTE: T he older th e touch scre en, the m ore Advanced Mode calibration points you need for an accurate calib ration. Use a stylus du ring Advanced Calibration for gr eater accuracy.
IPPC-9151 Series Users Manual 54.
55 Appendix 8 Plot Calibra- tion Data Check this function and a touch panel linearity co m- parison graph appears when you have fi nished Advanced Calibration. The blue line s show linearity before calibrati on and black lines show linearity after calibration.
IPPC-9151 Series Users Manual 56 Draw Tests or demonstrates the PenMount touch screen operation. The display shows touch location. Click Draw to start. Touch the screen with your finger or a stylus and the drawing scr een registers touch activity such left, right, up, down, pen up, and pen down.
57 Appendix 8 Multiple Monitors Multiple Monitors sup ports from two to six touch screen displays fo r one system. The PenMou nt drivers for Windows 2000/ XP support Multiple Monitors. This function supports from two to six tou ch screen displays for one system.
IPPC-9151 Series Users Manual 58 2. When the mapping screen message appears, click OK. 3. Touch each screen as it displays “Please touch this monitor.
59 Appendix 8 4. Touching all screens completes the map ping and the desktop reap- pears on the monitors. 5. Select a display and execute the ‘Calibration’ function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens.
IPPC-9151 Series Users Manual 60 Option This panel function suppo rts two modes—Operation Mode and Beep Sound Mode—which allow configu rati on for specific touch screen appli- cations, such as point-of-sales (POS) terminals. NOTE: 1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors function.
61 Appendix 8 About This panel displays inform ation about the PenMoun t controller and driver version..
IPPC-9151 Series Users Manual 62 8.4.2 PenMount Monitor Menu Icon The PenMount monitor icon (PM) appears in the men u bar of Windows 2000/XP system when you turn on PenMount Mon itor in PenMount Util- ities. PenMount Monitor has the follo wing functions.
63 Appendix 8 8.4.3 PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several di splay rotating software packages. Please s ee Chapter 5 for more informat ion.
IPPC-9151 Series Users Manual 64 8.5 Uninstall the PenM ount Windows 2000/XP driver 1. Exit the PenMount monitor (PM) in th e menu bar. 2. Go to Settings, then Control Panel, and then cli ck Add/Remove program. Select PenMount DMC900 0 and click the Add/Remove button.
CHAPTER 9 PCMCIA Sections include: • Introduction • Installation o f PCMCIA driver for Windo ws.
IPPC-9151 Series Users Manual 66 Chapter 9 PCMCIA 9.1 Introduction The IPPC-9151 is equipped with a high performance PCMCIA interface which complies wi th the 1995 PCMC IA card standard by using the RICOH Cardbus controller. The panel PC supports two PCMCIA card/ cardbus slots.
67 Chapter 9 9.2.1 Installation for Windows 1. a. In "Start", "Run", type the path: "D:IPPC-9151G& 9171G_ DRV&UtilityCardReader DriversWindo wsSetup.exe" 2. a. Click "Next" to continue the install ation.
IPPC-9151 Series Users Manual 68.
CHAPTER 10 Award BIOS Setup This chapter describes how to set BIOS configu- ration data.
IPPC-9151 Series Users Manual 70 Chapter 10 Award BIOS Setup 10.1 Award BIOS Setu p The IPPC-9151 com es with an Award BIOS chip that co ntains the ROM setup for your system . This chip serves as an interface between the pro- cessor and the rest of the mainboard's components.
71 Chapter 10 10.2.1 Standard CMOS Setup Standard CMOS Setup records some basic system hardware configura- tion and sets the system clock and error handl ing.
IPPC-9151 Series Users Manual 72 2. Use one of the arrow keys to m ove between options and modify the selected options by using PgUp / PgDn / + / - keys. Date (mm:dd:yy) The BIOS determines the day of the week from the other date informa- tion. This field is for information only.
73 Chapter 10 Drive A / Drive B Select this field to the t ype(s) of flop py disk drive(s) installed in your sys- tem. The choices are: 360 KB, 5.25 in; 1.2 MB, 5.25 in; 720 KB, 3.5 in; 1.44 MB, 3.5 in; 2.88 MB, 3.5 in; None. Video Select the type of pri mary video subs ystem in your computer.
IPPC-9151 Series Users Manual 74 Base Me mory Typically 640KB. Also called co nventional memory. The DOS operating system and conventional applications use this area. Extended Memory Above the 1MB boundary. Early IBM personal computers could not use memory above 1MB, but current PCs and their software can use extended memory.
75 Chapter 10 Virus Warning When enabled, you receive a warning message if a program (specifically, a virus) attempts to write to the boot sector or the partition table of the hard disk dr ive. You should then run an antivirus prog ram. Keep in mind that this feature protects only the boot sector, not the entire hard drive.
IPPC-9151 Series Users Manual 76 CPU Internal Cach e/External Cache Cache memory is additio nal memory that is much faster than conven- tional DRAM (system memory). CPUs from 486-ty pe up contain internal cache memory, and most, but not all, modern PCs have additional (exter- nal) cache memory.
77 Chapter 10 Gate A20 Option Gate A20 refers to the way the sy stem addresses memory above 1 MB (extended memory). When set to Fast , the system chipset controls Gate A20. When set to Normal, a pin in the keyboard controll er controls Gate A20. Setting G ate A20 to Fast imp roves system speed, p articularly with OS/2 and Windows.
IPPC-9151 Series Users Manual 78 C8000-CBFFF to DC000-D FFFF Shadow These options are used to shadow other expansion card R OMs. Small Logo (EPA) show 3. Press <ESC> to retu rn to the Main Menu when you finish setting up all items. 10.4 Advanced Chipset Features Advanced Chipset Features is used to modify the values of chipset buff- ers.
79 Chapter 10 DRAM Clock This item allo ws you to control the DRAM speed. The choices are : Host Clock, HCLK+3 3M. SDRAM Cycle Length Select CAS latency time in HCLKs of 2 or 3. The system desig ner already set the values. Do not change the default value unless you change specification s of the installed DRAM or the installed CPU.
IPPC-9151 Series Users Manual 80 AGP Driving Control This item allows you to adjust the AGP driving fo rce. Choose Manual to key in a AGP Driving Value in the next selection. This field is recom - mended to set in Auto for avoiding any error in your system.
81 Chapter 10 PCI Delay Transaction Leave this field at default. The choice: Enabled, Disabled. PCI Master 0 WS Write When Enabled, writes to the PCI bus are executed with zero wait states. The choice: Enab led, Disabled . PCI # 2 Access # 1 Retry Leave this field at default.
IPPC-9151 Series Users Manual 82 OnChip IDE Channel 0/1 The chipset contains a PCI IDE in terface with suppor t from two IDE channels. Select Enabled to activate the first and/or th e second IDE inter- face. Select Disabled to inactivate an interface if you install a primary and/or second add-on IDE interface.
83 Chapter 10 Primary Master / Slave PIO & Secondary Master / Slave PIO Choose Auto or Mode 0~4. The BI OS will detect the HDD mode type automatically when you choose Auto. You need to set to a lower mode than Auto when your hard disk becomes unstable.
IPPC-9151 Series Users Manual 84 IR Function Duplex This item allows you to select the IR half / full duplex function. The choices: Half; Full. TX, RX inverting enable This item allows you to enable the TX, R X inverting which d epends on different H/W requirement.
85 Chapter 10 10.6 Power Management Setup POWER MANAGEMEN T SETUP allows you to set the system’s power saving functions. Run the POWER MANAGEMENT SETUP as follows: 1. Choose“Integrated Peripherals”from the Main Menu and a list of options will app ear.
IPPC-9151 Series Users Manual 86 • Power Management: This option allows you to select the type (or degree) of power saving for Doze, Standby, and Susp end modes.
87 Chapter 10 Video Off Method This determines the manner in which the monito r is blanked. MODEM Use IRQ This determines the IRQ which the MODEM can use.
IPPC-9151 Series Users Manual 88 • Primary INTR: When set to on, any event occurring at will awaken a system which has been powered down. On(default):The system can not en ter the power saving mode when I/O ports or IRQ# is activated. Off:The system still can enter the power saving mode when I/O port s or IRQ# is activated.
89 Chapter 10 10.7 PnP/PCI Configuration PnP/PCI Configuration allows you to mo dify the system’s power saving functions. Run the PnP/PCI Configuration as follows: 1. Choose“PnP/PCI Configurati on”from the Main Menu and a list of options will app ear.
IPPC-9151 Series Users Manual 90 IRQ Resources Press Enter. Please refer to the list below: DMA Resources Press Enter. Please refer to the below list. PCI/VGA Palette Snoop This option allows the BIOS to preview VGA status, and to mo dify the information delivered from the feat ure Connector of the VGA card to MPEG card.
91 Chapter 10 10.8 PC Health Status This section helps you to get more inform ation about your sy stem includ- ing CPU temperature, FAN speed and voltage. It is recommended that you contact your mainboard supplier to get pro per values about the set- ting of the CPU temperature.
IPPC-9151 Series Users Manual 92 10.9 Frequency/Voltage Control Run the Frequency/Volt age Control as follows: 1. Choose“Frequency/V oltage Control”from the Main Menu and a list of options will appear. 2. Use one of the arrow keys to m ove between options and modify the selected options by using PgUp / PgDn / + / - keys.
93 Chapter 10 10.11 Set Password These option allows you to set your system passwords. The way to set up the password is as fol lows: 1. Choose “C hange Password” in the Main Menu and press <Enter>. Then following message appears: “Enter Password : “ 2.
IPPC-9151 Series Users Manual 94 10.12 Save & Exit Setup Save & Exit Setup allows you to save all modifications you have speci- fied into the CMOS memory. Highlight this option on the Main Menu and the following message appears: “Save to CMOS and Exit (Y/N) ? Y “ “Y” is for “Yes”, and “N” is for “No”.
Appendix A LCD Specifications and Selection Settings.
IPPC-9151 Series Users Manual 96 Appendix A LCD Specifications . IPPC-9120G/9150G/9151 Se ries LCD Specifications IPPC-9120G IPPC-9150G IPPC-9151 Display 12.1”TFT LCD 15”TFT LCD 15”TFT LCD Max. resolution 800 X 600 1024 X 768 1024 X 768 Colors 262k Dot pitch (mm) 0.
Appendix B Pin Assignments.
PPC-154 User’s Manual 98 Appendix B Pin Assignments B.1 ATX Power connector 1 (CN1) Table B.1: AT Power connector 1 (CN1) Pin Signal Pin Signal 1 3.3V 11 3.
99 Appendix B B.2 ATX power connector 2 (CN2) B.3 LVDS connector 1(CN4) Table B.2: ATX power co nnector 2 (CN2) Pin Signal Pin Signal 1G N D 31 2 V 2G N D 41 2 V Table B.
PPC-154 User’s Manual 100 B.4 LVDS connector 2(CN6) B.5 Inverter power connector (CN5) Table B.4: Table B.4: LVDS connector 2 (CN6) Pin Signal Pin Signal 1 VDD 11 RXIN6+ 2 VDD 12 RXIN6- 3G N D 1 3 G N D 4 GND 14 RXIN5+ 5 CLK1+ 15 RXIN5- 6 CLK1- 16 GND 7 GND 17 RXIN4+ 8 RXIN7+ 18 RXIN4- 9 RXIN7- 19 CONTRAST 10 GND 20 HPLG_DT Table B.
101 Appen dix B B.6 FDD connector (CN9) Table B.6: FDD connector (CN9) Pin Signal Pin Signal 1 Vcc(+5V) 14 Step 2 Index 15 GND 3 Vcc(+5V) 16 Write da ta 4 Drive select 17 GND 5 Vcc(+5V) 18 Write en ab.
PPC-154 User’s Manual 102 B.7 Internal speaker connector (CN15) B.8 IR connector (CN24) B.9 Fan power connector (FAN1 & FAN2) Table B.7: Internal speaker connector (CN15) Pin Signal 1 Speaker out_R - 2 Speaker out_R + 3 Speaker out_L + 4 Speaker out_L - Table B.
An important point after buying a device Advantech IPPC-9151 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Advantech IPPC-9151 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Advantech IPPC-9151 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Advantech IPPC-9151 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Advantech IPPC-9151 Series will certainly help you make a decision on the purchase.
If you already are a holder of Advantech IPPC-9151 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Advantech IPPC-9151 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Advantech IPPC-9151 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Advantech IPPC-9151 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
