Instruction/ maintenance manual of the product 350D Canon
Go to page of 13
8/6/2006 1 Camera Housing – Model 350D ( Canon ) User Manual Contents: 1. Introduction 2. Specification s 3. Function Controls 4 . Set up Instructions 5.
8/6/2006 2 1. Intr oduction 10 BAR Underwater Housings are small, light and rugged enough to be used on every dive. Use of clear polycarbonate allows for visual inspection of camera condition and the O - ring seal. 10 BAR Housings are designed for the ev er - increasing variety of models of digital still and video cameras.
8/6/2006 3 3. Function Controls 350D 1. Mode Dial, Power 6. ISO / AF, Metering Mode 11. Jump 2. Bulkhead 7. WB, Set 12. P lay, Delete 3. Main Dial 8. Illumination 13. Zoom Dial 4. Shutter 9. Exposure Compensation / Aperture, Drive Mode 5. AE/AF Lock, AF Point 10.
8/6/2006 4 (Fig. 1) Open Housing Procedure 4.3 Opening levers: After unscrewing and pulling out the pressure rel ease plug, the lid can be opened. To overcome the friction of opening, use lever (Fig.
8/6/2006 5 4 . 4 Special note on responsibility for watertight int egrity: Each housing is individually inspected and hydrostatically tested in the factory. The design of the main piston O - ring seal is among the most reliable in the industry and the watertigh t integrity is excellent.
8/6/2006 6 the outside of the housing is thoroughly toweled dry before opening up . After removing the lid and servicing the camera, replace the lid straight away, rather than leaving it lying around. Before replacing the lid, make sure that no contamination such as dust, hair, salt, sand etc.
8/6/2006 7 4.7 Mounting the camera in the housing: Remove the lens cap and wrist strap . T he pressure rel e ase plug should be pulled out before inserting the camera. Attach the plastic slide tray to the camera’s tripod mounting fixture with a coin, screwdriver or the end of the universal tool supplied (Fig.
8/6/2006 8 (Fig. 9) (Fig. 10) (Fig. 11) Replace the lid (Fig. 10) . Remember to ensure the pressure release plug is pulled all the way out while closing, otherwise the air cannot escape. Squeeze the lid close d all the way with t he hiss ing of expelled air.
8/6/2006 9 (Fig. 12) Note: If the O - ring is in good contact, a thin black line, about 0.5 to 1mm in width should be visible, where the O - ring is in contact with the lid. Follow this line all the way round the edge of t he seal, as a final check that the seal is good.
8/6/2006 10 5. Use & Care of Housing: 5.1 Pre Dive Function Check. Just before entering the water, make a habit of reviewing that you have carried out the proper steps to close the housing. and the pressure release plug screwed home. Make a visual check of the O - r ing seal.
8/6/2006 11 deposits that ma y have built up. No chemical cleaners should be used. Mild detergents e.g. shampoo and soap based cleaners are permitted. Important !!! Some household chemicals may harm P.
8/6/2006 12 7. Warranty The warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing.
8/6/2006 13 (Copy to be returned to 10 Bar Underwater Housings) The warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing.
An important point after buying a device Canon 350D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Canon 350D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Canon 350D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Canon 350D you will learn all the available features of the product, as well as information on its operation. The information that you get Canon 350D will certainly help you make a decision on the purchase.
If you already are a holder of Canon 350D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Canon 350D.
However, one of the most important roles played by the user manual is to help in solving problems with Canon 350D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Canon 350D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
