Instruction/ maintenance manual of the product RMC-2QD-2 Advanced Industrial Computer
Go to page of 17
Document Number: QIG-00001-A P/N: NONE Q Q u u i i c c k k I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e Copyright Notice All title, copyright and other intellectual property rig.
- Page 2 of 17 - T able of Content s I. Installing I/O shield .......................................................................................................... 3 II. Installing Motherboard......................................................
- Page 3 of 17 - I. Installing I/O shield Ty p e A _ I/O shield is provided with Motherboard 1. I/O shield snaps in from inside of chassis into the cutout Ty p e B 1.
- Page 4 of 17 - II. Installing Motherboard Ty p e A 1. Install the provided brass st andof fs o n chassis (1) at appropri ate positio ns 2. Place motherboard into the chassis, and make sure that the back panel I/O shield cutout and chassis mounting st andof fs align co rrectly .
- Page 5 of 17 - III. Installing riser card (Base on socket’s type, chassis’ height and PCI card’s type to select the riser ca rd) Ty p e A ： 1U solution 1. Insert the PCI card to riser card an d then install the rise r card at appropriate PCI slot.
- Page 6 of 17 - IV. How to use clamp bar 1. Extract the thumb screw and swing backward the clamp 2. Fit the clamp bar over the add -o n card and tight en the thumb screw to bring the clamp forward thus pushing down on the card. 3. Fix the thumb screw back.
- Page 7 of 17 - V. Installing 2.5” HDD Ty p e A 1. Install the 2 bracket s on both sides of 2.5” HDD wit h 4 x M3 screws 2. Install the provided 2.
- Page 8 of 17 - VI. Installing 3.5” OS HDD Ty p e A . Install HDD on the top of bracket by 4 x 6# screws. Ty p e B Install the HDD on the bracket near power su pply side by 2 x 6# screws. Ty p e C Lock the HDD with the right and left bracket by 4 x 6# screws and then lock it in the bottom of chassis.
- Page 9 of 17 - VII. Installing 3.5” Hot-Swap HDD Tray 1. Push the HDD tray clip rightward and pull on the handle simult aneously , then unlatch HDD tray handle by swinging the handl e forward an d le ft.
- Page 10 of 17 - VIII. How to use the Slim CD-Ro m & Floppy Direct Device cage ** Installing 3.5” FDD or 3.5” HDD 1. Remove the knock-out shield from 3.5” device bay 2. Remove the USB port PC board 3. Install 3.5” FDD from both sides with 4 x M3 screws 4.
- Page 1 1 of 17 - I I X X . . I I n n s s t t a a l l l l i i n n g g S S l l i i m m C C D D - - R R O O M M Please install slim CD-RO M adaptor first before installing the slim CD-ROM . . Slim CD-ROM adaptor inst allation guide 9 Inst alling Slim CD-ROM Ty p e A 1.
- Page 12 of 17 - Ty p e B 1. Remove slim CD-ROM bezel by loosening the 2 screws on the sides. 2. Attach the two brackets on two side s of slim CD-ROM and install the mountin g 4 x M2 screws. ( 1 ) ( 2 ) Ty p e C 1. Release 1 screw to remove S-CD cover .
- Page 13 of 17 - X X . . I I n n s s t t a a l l l l i i n n g g S S l l i i m m F F D D D D Ty p e A 1. Mount slim FDD onto bracket by installing and tightening 4 x M2.5 screws. 2. Mount slim FDD adaptor by securing it with 2 x M3 screws. 3. Insert the slim FDD bracket module back into the chassis and fixed it by 2 scre ws.
- Page 14 of 17 - ( 3 ) ( 4 ) Ty p e C 1. Release 2 thumb screws to pull the slim FDD bracket out. 2. Remove the knock-out shield. Inst all the slim FDD by fix 4 x M2.5 and adaptor by 2 x M3 screws as (2). 3. Connecting both data a nd power cables before inst all the slim FDD back into the cha ssis.
- Page 15 of 17 - XI. Installing 5.25” Bay Device Ty p e A 1. Remove front blanking panel by relea sin g the 2 scre ws 2. Attach the two brackets with thumb scre w supplied in the accessory kit and insta ll the M3 screws to the both sides of the device 3.
- Page 16 of 17 - XII. Installing 3.5” Bay Device Remove front shield by releasing the 2 scre ws. Install the each 3.5 device bay with 4 x M3 screws at appro priate location.
- Page 17 of 17 - XIII. Glossary Ricer Card A card that plugs into the motherboard to provide a perpendicular extension of the bus. Adapter cards are then plugged into the riser instea d of the motherb oard, allowing a lower profile to the case. Most often used for desktop systems t hat sit u nder the monitor .
An important point after buying a device Advanced Industrial Computer RMC-2QD-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Advanced Industrial Computer RMC-2QD-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Advanced Industrial Computer RMC-2QD-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Advanced Industrial Computer RMC-2QD-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Advanced Industrial Computer RMC-2QD-2 will certainly help you make a decision on the purchase.
If you already are a holder of Advanced Industrial Computer RMC-2QD-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Advanced Industrial Computer RMC-2QD-2.
However, one of the most important roles played by the user manual is to help in solving problems with Advanced Industrial Computer RMC-2QD-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Advanced Industrial Computer RMC-2QD-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
