Instruction/ maintenance manual of the product 6C105 Cabletron Systems
Go to page of 38
6C105 Smar tSwitch 6000 Overview and Setup Guide 1 23 4 5 PS1 PS2 6C405 9032016-04.
.
6C105 Overview and Setup Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes ha ve been made.
Notice ii 6C105 Overview and Setup Guide DOC NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Notice 6C105 Overview and Setup Guide iii CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE . You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.
Notice iv 6C105 Overview and Setup Guide DECLARATION OF CONFORMITY Application of Council Directiv e(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representativ e Name: Mr.
6C105 Overview and Setup Guide v CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Guide ......................................................................... 1-1 1.2 Structure of This Guide............................................................
Contents vi 6C105 Overview and Setup Guide.
6C105 Overview and Setup Guide 1-1 CHAPTER 1 INTR ODUCTION W elcome to the Cabletron Systems 6C105 SmartSwitch 6000 Overview and Setup Guide . This guide e xplains how to set up and configure the Cabletron Systems 6C105 SmartSwitch 6000 chassis.
Chapter 1: Introduction 1-2 6C105 Overview and Setup Guide 1.3 DOCUMENT CON VENTIONS Throughout this guide the follo wing symbols are used to call attention to important information. 1.4 USING THE 6C105 MANUAL SET Other manuals hav e been dev eloped for the interf ace modules that can be installed in the 6C105 chassis.
Getting Help 6C105 Overview and Setup Guide 1-3 1.5 GETTING HELP If you need additional support related to this de vice, or if you have an y questions, comments, or suggestions concerning this manual,.
Chapter 1: Introduction 1-4 6C105 Overview and Setup Guide 1.6 OVERVIEW The Cabletron Systems 6C105 chassis design provides fiv e 2.4-inch slots that can contain a v ariety of interface modules. The chassis supports redundant po wer supplies, LANVIEW Diagnostic LEDs, and is 19-inch rack mountable.
Features 6C105 Overview and Setup Guide 1-5 1.7 FEATURES Redundant P ower Supply Modules The 6C105 supports two po wer supply modules which reside in the slots labeled PS1 and PS2. Each po wer supply module supports an ac input connector that allows each po wer supply to be connected to a separate ac power source.
Chapter 1: Introduction 1-6 6C105 Overview and Setup Guide A uto-Ranging Po wer Supplies The 6C105 po wer supply modules automatically adjust to the input voltage and frequenc y . No additional adjustments are necessary . Hot Swapping T o reduce network downtime, the po wer supply modules are also hot swappable.
6C105 Overview and Setup Guide 2-1 CHAPTER 2 INSTALLATION REQUIREMENTS AND SPECIFICATIONS This chapter describes the follo wing: • Site guidelines that must be met before installing a 6C105 into a rack or cabinet • 6C105 configuration guidelines • Operating specifications for the 6C105 enclosure and po wer supply modules 2.
Chapter 2: Installation Requirements and Specifications 2-2 6C105 Overview and Setup Guide 2.2 CONFIGURATION GUIDELINES The 6C105 has 5 slots that accept interface modules. The slots are numbered 1 to 5 beginning from the left. There are two additional slots located on the far right of the chassis that are reserv ed for power supply modules.
Operating Specifications 6C105 Overview and Setup Guide 2-3 2.3.1 Physical Specifications The physical specifications for the 6C105 chassis, 6C205-1, 6C205-2, 6C205-3 po wer supply modules and the .
Chapter 2: Installation Requirements and Specifications 2-4 6C105 Overview and Setup Guide 2.3.2 P ower Suppl y Requirements The po wer supply requirements for the 6C205-1, 6C205-2 and 6C205-3 po wer supply modules are as follows: 6C205-1 A C P ower Supply 6C205-2 DC P ower Supply 6C205-3 A C P ower Supply 2.
LEDs 6C105 Overview and Setup Guide 2-5 Figure 2-1 P ower Supply LEDs T able 2-1 P ower Supply LED States and Their Definitions LED Name Color Status PWR (P ower) Green All outputs and input of the power supply are within regulation. Red Any output or input of the specific po wer supply is out of regulation.
Chapter 2: Installation Requirements and Specifications 2-6 6C105 Overview and Setup Guide 2.4.2 Fan T ray LED The follo wing table describes the different states of the fan tray LED and their definitions. Refer to Figure 2-2 for the location of the fan tray LED.
6C105 Overview and Setup Guide 3-1 CHAPTER 3 6C105 SETUP This chapter contains instructions on setting up the Cabletron Systems 6C105 chassis. A Phillips screwdri ver is needed to install the unit in a 19-inch equipment rack, to install the cable management bar , to secure the po wer supply module(s) and to remo ve and reinstall the fan tray .
Chapter 3: 6C105 Setup 3-2 6C105 Overview and Setup Guide 3.2 SETTING UP THE 6C105 The follo wing sections describe the procedures that must be followed to complete the installation of the 6C105. 3.2.1 Installation Order Once a suitable site has been chosen, the 6C105 can be installed.
Setting Up the 6C105 6C105 Overview and Setup Guide 3-3 3.2.2 Installing the Cable Management Bar T o install the cable management bar, proceed as follo ws: 1. Remove the cable management bar from the shipping box. Ensure that there are four screws inside the bag with the cable management bar.
Chapter 3: 6C105 Setup 3-4 6C105 Overview and Setup Guide 3.2.3 Rack Mounting the 6C105 The 6C105 can be mounted in a standard 19-inch equipment rack. T wo people may be required to lift the chassis into place. The chassis is secured with ten scre ws, five on each side.
Setting Up the 6C105 6C105 Overview and Setup Guide 3-5 3.2.4 Attaching the Electr ostatic Discharge Wrist Strap The Electrostatic Discharge (ESD) Wrist Strap must be attached before handling the po wer supplies, fan tray , or modules for the 6C105. In addition, observe all precautions when handling these modules to pre vent damage from ESD.
Chapter 3: 6C105 Setup 3-6 6C105 Overview and Setup Guide 3.2.5 Installing a P ower Suppl y Module Y ou must install at least one power supply in the 6C105 chassis. One po wer supply provides sufficient po wer for most module configurations but a second po wer supply can be installed to provide a redundant, load sharing po wer source.
Setting Up the 6C105 6C105 Overview and Setup Guide 3-7 4. Slide the power supply module into the slot labeled PS1 as follows: a. Hold the module by placing one hand on the handle located on the module front panel and using the other hand to support the body of the module.
Chapter 3: 6C105 Setup 3-8 6C105 Overview and Setup Guide Figure 3-4 Installing the P ower Supply Module(s) After installation of the po wer supply modules is completed the 6C105 is ready to be po wered up; howe ver , Cabletron Systems recommends that installation of all modules for the 6C105 be completed before po wering up the 6C105.
Setting Up the 6C105 6C105 Overview and Setup Guide 3-9 3.2.6 Installing 6C105 Interface Modules The 6C105 Interface Modules can be installed in an y of the 5 slots that are av ailable. T o install a module, proceed as follows: 1. Remove the blank panel covering the slot in which the Interface Module will be installed.
Chapter 3: 6C105 Setup 3-10 6C105 Overview and Setup Guide Figure 3-5 Installing a Module 1 2 3 45 PS1 PS2 Plastic Locking T ab Slot Number 2361-02 2159-01 Circuit Card Card Guides Metal Back-Panel Pl.
P owering Up a 6C105 with A C P ower Supplies 6C105 Overview and Setup Guide 3-11 3.3 P OWERING UP A 6C105 WITH A C P OWER SUPPLIES T o power up a 6C105 with ac po wer supply modules proceed as follows: 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the bottom of the power supply.
Chapter 3: 6C105 Setup 3-12 6C105 Overview and Setup Guide Figure 3-6 P ower Supply DC ON/OFF Switch and DC Input P ower Strip DC P ower Supply Requirement f or Each Supply Each DC po wer supply input requires either a 48 VDC or 60 VDC power source, rated at a minimum of 17 Amps.
P owering Up a 6C105 with DC P ower Supplies 6C105 Overview and Setup Guide 3-13 Installation Requirement Each DC po wer supply input requires either a 48 VDC or 60 VDC power source supplied by three 10 A WG (American W ire Gauge) copper wires. These wires must be terminated with either ring or spade terminals that accept a #6 scre w .
Chapter 3: 6C105 Setup 3-14 6C105 Overview and Setup Guide If you experience an y problems during the installation of the 6C105, contact Cabletron Systems Global Call Center for assistance.
Removing and Reinstalling the F an T ray 6C105 Overview and Setup Guide 3-15 Figure 3-8 Removing the F an T ray 3.5.2 Reinstalling the Fan T ray T o reinstall the fan tray , refer to Figure 3-9 and proceed as follows: 1. Locate the ESD wrist strap shipped with the 6C105.
Chapter 3: 6C105 Setup 3-16 6C105 Overview and Setup Guide 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it. 5. Once the tray is in place, tighten the slotted screws with a screwdriver to secure the tray to the 6C105.
Removing and Reinstalling the F an T ray 6C105 Overview and Setup Guide 3-17 Figure 3-9 Reinstalling the Fan T ray Slot Guides Slotted Screws (2) 1 23 4 5 PS1 PS2 2016_08 6C405.
Chapter 3: 6C105 Setup 3-18 6C105 Overview and Setup Guide.
An important point after buying a device Cabletron Systems 6C105 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cabletron Systems 6C105 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cabletron Systems 6C105 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cabletron Systems 6C105 you will learn all the available features of the product, as well as information on its operation. The information that you get Cabletron Systems 6C105 will certainly help you make a decision on the purchase.
If you already are a holder of Cabletron Systems 6C105, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cabletron Systems 6C105.
However, one of the most important roles played by the user manual is to help in solving problems with Cabletron Systems 6C105. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cabletron Systems 6C105 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
