Instruction/ maintenance manual of the product 6A000/ZX-250 Cabletron Systems
Go to page of 268
SmartCell 6A000/ZX-250 Reference Manual 35 Industrial Wa y Rochester, NH 03866-50 05 USA (603) 332-9400 Part # 04-0044-02 Rev. A Order # 9032400.
ii SmartCell 6A000/ZX-250 Reference Manual NOTICE Cabletron Systems reserves the right to m ake changes in specifications and other infor mation contained in this document without prior notice. The r eader should in all cases consult Cabletron Systems to d etermine whether any such changes have been made.
SmartCell 6A000/ZX-250 Referen ce Manual iii REVISION HISTORY Document Name: SmartCel l 6A000/ZX-25 0 Reference Manu al Document Order Number: Order # 903 2400 Document Part Number : Part # 04 -0044-02 R ev .
iv SmartCell 6A000/ZX-250 Reference Manual.
SmartCell 6A000/ZX-250 Refere nce Manual v T ABL E OF CONT ENT S 1 Introdu ction 1-1 Audience and Scope 1-1 Definitions 1-1 Content 1-1 Sections 1-2 Conventions 1-2 Abbreviations 1-3 Help Options 1-4 .
vi SmartCell 6A000/ZX-250 Reference Manual Table of Contents IPATMStat 2-64 LANEClient 2-66 LECS 2-68 LECSAddress 2-70 LECSELAN 2-72 LECSELANLEC 2-75 LECSStat 2-78 LECSTLVParam 2-81 LECSTLVSet 2-83 LE.
SmartCell 6A000/ZX-250 Reference Manual vii Table of Content s Switch 2-182 SwitchConfig 2-184 SwitchName 2-188 SwitchTrafficCongestion 2-189 TrafficDe scriptor 2-197 TrustedNMS 2-199 UNIRoute 2-201 V.
viii SmartCell 6A000/ZX-250 Reference Manual Table of Contents.
SmartCell 6A000/ZX-250 Reference Manual ix LIST OF T ABLES 1-1 Li st of Oper ators 1-5 1-2 Operator Table Explanation 1-6 1-3 Param eter Table Explanatio n 1-7 1-4 Descript ion Table Explanatio n 1-8 .
x SmartCell 6A000/ZX-250 Reference Manual Li st of Tables.
SmartCell 6A000/ZX-250 Reference M anual 1-1 1 INTRODUCTION This reference manu al describes the console commands for the SmartCell 6A000 and SmartCell ZX-250 A TM switches. The two switches share a common co nsole interface and are r eferred to in this manual as the SmartCell 6A000 /ZX- 250.
1-2 SmartCell 6A000/ZX-250 Reference Manual Introduction Sections Read "Switch Attribute" for an example and definition of the various sections under each switch attribute as well as a descri ption of how the manua l is o rganized. Each section begins with a switch attribute headin g (for example, "PVCByID").
SmartCell 6A000/ZX-250 Reference M anual 1-3 Introduction IP NetMask : 255.255.255.0 IP/ATM Client 3 ============================================================================== Client State : Opera.
1-4 SmartCell 6A000/ZX-250 Reference Manual Introduction Help Op tions If you wan t information on a specific command, type ? or help before typing the command and you will get a brief description of th e command and all its input parameters.
SmartCell 6A000/ZX-250 Reference M anual 1-5 Introduction Switch Attribute This section —immediately belo w the heading—gives a brief descri ption of what the switch attr ibute does. A detailed description o f each command is available under "Descriptions.
1-6 SmartCell 6A000/ZX-250 Reference Manual Introduction Opera tors Parameters appear in the p arameter tables in the same order and spelling as the switch shows them. Most switch attribu te descriptions show two tables —Input Parameter and Output P arameter .
SmartCell 6A000/ZX-250 Reference M anual 1-7 Introduction Only one parameter table in a switch attribute section means either that switch attribute uses only input parameters or that the output parameters are identical to the input parameters. The h eading of the table indicates which is the case.
1-8 SmartCell 6A000/ZX-250 Reference Manual Introduction Description s The following is an ex ample of a description section. It is located under "BUSELAN." Note the detailed d escription of the command followin g the table. Exam ples Examples are copied ex actl y fro m the swit ch con sole to show you what you should see.
SmartCell 6A000/ZX-250 Reference M anual 1-9 Introduction switch_prompt # show buselan ELANNumber : 103 ELAN : elan103 ELAN Number : 103 ELAN Name : elan103 ATM Address :39:00:00:00:00:00:00:00:20:D4:14:15:00:00:20:D4:14:15:66:02 Max Frame Size : 4544 Connection Method : PVC Distribute VPI/VCI: 0/50 LAN Type : 802.
1-10 SmartCell 6A000/ZX-250 Reference Manual Introduction modify (set) AlarmConfig AlarmV erbose BUSELAN CACParams ILMIAdminStatus IP A ddress IP A TMC lient LANEClient LECSAddress LECSELAN LECSELANLE.
SmartCell 6A000/ZX-250 Refere nce Manual 1-11 Introduction show (dis play) activate/d eactivate ALARM AlarmConfig AlarmV erbose BUSClient BUSELAN B USLECStat BUSStat CACParams CACStat C lient ClientAR.
1-12 SmartCell 6A000/ZX-250 Reference Manual Introduction backup/restore clear disabl e/enab le exit flus h history switch ALARM BUSStat Config LESStat LogBuff er LogT race PortStat disable/enable exi.
SmartCell 6A000/ZX-250 Refere nce Manual 1-13 Introduction passwd restart setup shutdown start stop passw d client Switch shutdown LECS LES log Ping LECS LES log.
1-14 SmartCell 6A000/ZX-250 Reference Manual Introduction updat e firmware.
SmartCell 6A000/ZX-250 Reference M anual 2-1 2 C ONSOLE COMMANDS Alarm Use Alarm to set alarm messaging features. Opera tors show, clear, flush Parame ters In the Output Parameter table below , ( </d> ) indicates param eters that are available only thro ugh the show alarm /d (detailed) command.
2-2 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [T imeStamp] ( </s> ) T ime (in system up time) when the alarm message entry was created. The time stamp is in the for mat [hrs:mins:secs :msecs]. n/a [Message] ( </s> ) Numeric code that specifies the message in the log entry that generated this alarm message.
SmartCell 6A000/ZX-250 Reference M anual 2-3 Console Commands Description s [Num of logs per file] Number of alarm messages that can be held by each file within the alarm messag e buffer .
2-4 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples (AlarmVerbose is off) switch_prompt # modify alarmverbose Mode(On) : off Setting Alarm Verbose Mode to Off switch_prompt # show .
SmartCell 6A000/ZX-250 Reference M anual 2-5 Console Commands Writing into Alarm Configuration Alarm directory : ALARM Alarm Config file : alarmc.db Alarm Filename : zalarm Num of alarm files : 32 Sta.
2-6 SmartCell 6A000/ZX-250 Reference Manual Console Com mands AlarmConfi g Use AlarmConfig (alarm configuration) to determine alarm message b uffer file configur ation.
SmartCell 6A000/ZX-250 Reference M anual 2-7 Console Commands Description s [Alarm Config file] Name of the file that con tains the current configuration o f the alarm message buff er . alarmc.db [Alarm Filename] Base name of the set of files within the flash file system where alarm messages are stored.
2-8 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # add alarmconfig AlarmNumFiles(32) : StartFileNum(0) : NumFilesUsed(0) : NumAlarmsPerFile(8): switch_prompt # swi.
SmartCell 6A000/ZX-250 Reference M anual 2-9 Console Commands AlarmV erbose Use AlarmV erbose to determine how much information is displayed in the alarm messages.
2-10 SmartCell 6A000/ZX-250 Reference Manual Console Com mands BUSClient Use BUSClient (broadcast and unknown server client) to manage the mapping between the BUSELAN and the LANE clients that have joined the BUSELAN. Clients are uniq uely identified by their LECId.
SmartCell 6A000/ZX-250 Refere nce Manual 2-11 Console Commands Exam ples switch_prompt # delete busclient ELANNumber(0) : LECId(0) : 14 LECId : 14 ATMAddress : 39:00:00:00:00:00:00:00:20:D4:14:11:80:0.
2-12 SmartCell 6A000/ZX-250 Reference Manual Console Com mands BUSELAN Use BUSELAN (broadcast and unkn own server emulated LAN) to determine the characteristics of the specified ELAN maintained by the BUS. If the corresponding LESELAN exists, it should be iden tical.
SmartCell 6A000/ZX-250 Refere nce Manual 2-13 Console Commands Parame ters Input Parameter Description V alue/Field Size Default [ELANNumber] Numb er of the ELAN to which the BUS belongs. 0- 127 ALL [ELANName] Name of the ELAN to which the BUS belongs.
2-14 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # add buselan ELANNumber(0) : 102 ELANName(ELAN102) : ConnectMethod(SVC) : ELANType(802.
SmartCell 6A000/ZX-250 Refere nce Manual 2-15 Console Commands The example below changes ELAN102 fr om an Ethernet BUSELAN to a T oken Rin g BUSELAN, changing the MTU to reflect the chang e in ELAN type. It assumes the LES has already been changed. switch_prompt # modify buselan 102 ELANName(ELAN102) : ConnectMethod(svc) : ELANType(802.
2-16 SmartCell 6A000/ZX-250 Reference Manual Console Com mands BUSLECStat Use BUSLECStat (broadcast and unkn own server LAN em ulation client statistics) to view traffi c statistics for all or specified clients that have joined the BUSELAN.
SmartCell 6A000/ZX-250 Refere nce Manual 2-17 Console Commands Description Exam ple switch_prompt # show buslecstat ELANNumber(0) : LECId(0) : Client statistics for ELAN ELAN000 ======================.
2-18 SmartCell 6A000/ZX-250 Reference Manual Console Com mands BUSStat Use BUSStat (broadcast and unkno wn server statistics) to view statistics that the BUS maintains for each ELAN. Opera tors show, clear Parame ters SER VER SV C X Input Parameter Description V alue/Field Size Default [ELANNumber] N umber of the EL AN to which the BUS belongs.
SmartCell 6A000/ZX-250 Refere nce Manual 2-19 Console Commands Description s Exam ples switch_prompt # show busstat 3 ELAN ELAN003 Statistics Out Octets : 450432 Out Unicast : 7030 Out Multicast : 3 I.
2-20 SmartCell 6A000/ZX-250 Reference Manual Console Com mands CACParams Use CACParams (call adm issi on control parameters) to d etermine the allocation of bandwid th to SVCs (switched virtual circuits) an d PVCs (permanent vi rtual circui ts) for individ ual ports on the s witch.
SmartCell 6A000/ZX-250 Refere nce Manual 2-21 Console Commands Description s Exam ples switch_prompt # modify cacparams PortNumber :( ALL ): a2 AllocScheme :( ) : moderate switch_prompt # switch_promp.
2-22 SmartCell 6A000/ZX-250 Reference Manual Console Com mands CACStat Use CACStat to see the CAC (call admission control) statistics. Opera tor show Parame ters SER VER SV C XX Input Parameter Description V alue/Field Size Default [PortNumber] Port number on the sw itch.
SmartCell 6A000/ZX-250 Refere nce Manual 2-23 Console Commands Description Exam ples switch_prompt # show cacstat PortNumber(ALL) : Port# Bandwidth Available Bandwidth Allocated (In Kb/s) (In Kb/s) To.
2-24 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Client Use Client to determine all or local LANE (LAN em ulation) and IP/A TM (IP over A TM) clients on the switch.
SmartCell 6A000/ZX-250 Refere nce Manual 2-25 Console Commands Description s [LECS Address] (</d>) A TM address of the LECS. [LES Address] (</d>) A TM address of the LANE server . [LAN T ype] (</d>) T ype of ELAN. [MTU] (</d>) Maximum transfer unit assigned for this client.
2-26 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # delete client 4 IP/ATM Client4 Address: 39:00:00:00:00:00:00:00:00:00:14:15:00:00:00:7A:01:01:5B:00 Confirm(y/n.
SmartCell 6A000/ZX-250 Refere nce Manual 2-27 Console Commands W ith the following example (</d>) , notice how y ou get the s ame amount of detail whether you sp ecify th e client or accept the .
2-28 SmartCell 6A000/ZX-250 Reference Manual Console Com mands ClientARP Use ClientARP (client address resolution protocol) to view the mapping of the MAC (media access control) or IP addresses to an A TM address for LANE (LAN emulation) or IP/A TM (IP over A TM) clients.
SmartCell 6A000/ZX-250 Refere nce Manual 2-29 Console Commands Description Exam ple switch_prompt # show clientarp ClientNumber(ALL) : LANE Client 0 ARP Table MAC Address ATM Address =================.
2-30 SmartCell 6A000/ZX-250 Reference Manual Console Com mands ClientStat Use ClientStat (client stati stics) to view LANE (LAN emulation) o r IP/A TM (IP ov er A TM) clien t stati stics.
SmartCell 6A000/ZX-250 Refere nce Manual 2-31 Console Commands [Broadcast Packets] (</d>) Number of br oadcast packets received or tran smitted. [Error Packets] (</d>) Number of error packets received or transmitted. [Dropped Packets] (</d>) Number of received or transmitted packets dropped.
2-32 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description Exam ples The examples show statisti cs for all clients, detail (</d>) for all clients, an IP/A TM client, and a LANE client .
SmartCell 6A000/ZX-250 Refere nce Manual 2-33 Console Commands switch_prompt # show clientstat ClientNumber(ALL): Client Type RxPkts TxPkts RxOctets TxOctets ==========================================.
2-34 SmartCell 6A000/ZX-250 Reference Manual Console Com mands switch_prompt # show clientstat 3 Stats for IP/ATM client 3 ============================================================================ .
SmartCell 6A000/ZX-250 Refere nce Manual 2-35 Console Commands ClientVC Use ClientVC (client virtual circuit) to view which VCs are associated with a particular local LANE or IP over A TM client's ARP (address resolutio n protocol) entries. Clien tVC is similar to ClientAR P , except th at it also includes details of VPI/VCI numbers.
2-36 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description Exam ple switch_prompt # show clientvc ClientNumber(ALL) : LANE Client 0 VC Table MAC Address VPI/VCI ATM Address ===========.
SmartCell 6A000/ZX-250 Refere nce Manual 2-37 Console Commands Community Use Commu nity to g roup NMS (n etwork managem ent sys tem) hosts by pr ivilege l evel. Hosts are collec tively called communit ies, and their privilege l evel determines th e type of informatio n access permitted by the switch.
2-38 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # add community Name() : boris IpAddr() : 90.1.1.1 Priviledge(read) : switch_prompt # switch_prompt # show community Community Name IP Address Privilege =========================================================================== ILMI 0.
SmartCell 6A000/ZX-250 Refere nce Manual 2-39 Console Commands Confi g Use Config to erase the confi gur ation information on the SmartCell ZX-250. Before using the clear config command, y ou shoul d backup the s witch co nfigurat ion usin g the backup switch command.
2-40 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description Exam ple switch_prompt # clear config You should backup your configuration using the "backup switch" command, in case you want to recover this configuration Continuing will permanently erase the current switch configuration, and requires a switch reboot.
SmartCell 6A000/ZX-250 Refere nce Manual 2-41 Console Commands ELAN Use ELAN (emulated local area network) to create or delete ELANs on the switch. This is a qu ick configuration method of managing ELAN serv er entries within one comman d.
2-42 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Outpu t Paramet er Description [LES Address] A TM address of the LANE server .
SmartCell 6A000/ZX-250 Refere nce Manual 2-43 Console Commands Exam ples switch_prompt # add elan ELANNumber(0) : 11 ELANName(ELAN011) : ConnectMethod(SVC) : ELANType(802.
2-44 SmartCell 6A000/ZX-250 Reference Manual Console Com mands B switch_prompt # add leselan 4 ELANName(ELAN004) : ConnectMethod(SVC) : ELANType(802.3) : Multipoint(YES) : MTU(1516) : Distribute(PROXY) : BUSATMAddress() : switch_prompt # switch_prompt # add buselan 4 ELANName(ELAN004) : ConnectMethod(SVC) : ELANType(802.
SmartCell 6A000/ZX-250 Refere nce Manual 2-45 Console Commands Exit Use Exit to disconnect your console con nection from the switch. Opera tor exit Parame ters There are no parameters for th is command. Just type exit at the switch prompt. Description Exam ple switch_prompt # exit Exiting SmartCell 2X Command Console SmartCell 2X version 1.
2-46 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Firmw are Use Firmware to re-prog ram the switch application sof tware when you want to p erform a switch u pgrade.
SmartCell 6A000/ZX-250 Refere nce Manual 2-47 Console Commands Exam ple SmartCell ZX # update firmware ServerIP() : 204.95.77.240 Path() : server/server.ima You are updating the code image in the flash. Are you sure this is what you want to do? Confirm(y/n)?: y Verifying bootfile server/server.
2-48 SmartCell 6A000/ZX-250 Reference Manual Console Com mands History Use Histo ry to view the l ast five co mmands you ent ered. Ent er History i f you want t o use one of those commands again. Opera tor history Parame ters This command has n o parameters.
SmartCell 6A000/ZX-250 Refere nce Manual 2-49 Console Commands IISPRoute Use IISP Route (in terim int er-switch s ignaling protocol ) to man ipulate the IISP rou tes confi gured on the swit ch (se e “UNIRoute” for further routing commands).
2-50 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Y ou can create a default I ISP route if you enter only the port n umber and a weighting value [Metric] for the route (see Examples below). Y ou can set multiple local configurat ions to choose one of th e parall el links f or next-h op rou ting.
SmartCell 6A000/ZX-250 Refere nce Manual 2-51 Console Commands Exam ples switch_prompt # add iisproute AtmAddress() : 39:00:00:00:00:00:00:00:00:00:11:22:33 PortNumber(A1): Metric(1) : switch_prompt #.
2-52 SmartCell 6A000/ZX-250 Reference Manual Console Com mands ILMIAdminStatus Use ILMIAdminStatus (integrated local m anagement interface administration status) to control the operation of the ILMI pr otocol on every por t on th e switch .
SmartCell 6A000/ZX-250 Refere nce Manual 2-53 Console Commands Exam ples switch_prompt # modify ilmiadminstatus PortNum :( ALL ): a1 IlmiAdminStatus :( enable ): disable switch_prompt # switch_prompt .
2-54 SmartCell 6A000/ZX-250 Reference Manual Console Com mands IP Address Use IP Address to change IP addr esses of t he Ethernet port and IP netmask on t he switch. Opera tor modify Parame ters Description SER VER SV C XX Input Parameter Description V alue/Field Size Default [IP Address] IP addres s of the Ethernet port.
SmartCell 6A000/ZX-250 Refere nce Manual 2-55 Console Commands Exam ple switch_prompt # modify ipaddress IPAddress(200.30.72.122) : 1.1.1.11 IPNetMask(255.255.255.0) : Confirm(y/n)?: y Changing IP Address on System. Telnet Session (if any) will be lost.
2-56 SmartCell 6A000/ZX-250 Reference Manual Console Com mands IP A TMARP Use IP A TMA RP (IP over A TM address resolution protocol) to see IP/A TM ARP server tables. Unlike LANE client or IP/A TM (IP over A T M) client ARP tables (see show clientarp ), these ARP entries are registered with the IP/A TM ARP server .
SmartCell 6A000/ZX-250 Refere nce Manual 2-57 Console Commands IP A TMClient Use IP A TMClient (IP over (/) A TM client) to manipula te either local IP/A TM clients or IP/A TM clients acting as an IP/A TM server , or if you want to configure an IP/A TM client on the IP/A TM server itself.
2-58 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Parame ters Input Parameter Description V al ue/Field Size Default [ClientNum ber] Number of the client. 0-127 ALL [ServerT yp e] IP/A TM server type. LOCAL, EXTERNAL, NONE NONE [ServerAddress] A TM address of the IP/A TM server .
SmartCell 6A000/ZX-250 Refere nce Manual 2-59 Console Commands Description s Exam ples switch_prompt # add ipatmclient ClientNumber(0) : 50 ServerType(NONE) : local ServerAddr() : IpAddr() : 101.
2-60 SmartCell 6A000/ZX-250 Reference Manual Console Com mands NetMask(255.0.0.0): MTU(9180) : switch_prompt # switch_prompt # modify ipatmclient ClientNumber(0) : 50 ServerType(LOCAL) : ServerAddr() : IpAddr(101.
SmartCell 6A000/ZX-250 Refere nce Manual 2-61 Console Commands IP A T MPVC Use IP A TMPVC (IP over A TM permanent virtual circuit) to man ipulate IP/A TM PVC clients on a PVC IP/A TM VLAN (virtual LAN).
2-62 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # add pvc ConnType(PTP) : LowPort(A1) : LowVPI(0) : LowVCI(33) : 130 HighPort(A1) : b4 HighVPI(0) :.
SmartCell 6A000/ZX-250 Refere nce Manual 2-63 Console Commands switch_prompt # show client 0 IP/ATM Client 0 =========================================================================== Client State : Operational Client Address : 39:00:00:00:00:00:00:00:20:D4:14:22:80:00:00:0A:01:01:02:00 Server : is none MTU : 9180 IP Address : 10.
2-64 SmartCell 6A000/ZX-250 Reference Manual Console Com mands I PAT M S t a t Use IP A TMStat (IP over A TM statistics) to view details of the IP/A TM (IP over A TM) client server . Opera tor show Parame ters SER VER SV C X Input Parameter Description V alue/Field Size De fault [ClientNum ber] Number of the client.
SmartCell 6A000/ZX-250 Refere nce Manual 2-65 Console Commands Description Exam ples switch_prompt # show ipatmstat ClientNumber(ALL): Client ArpReqs ArpReps ArpUnrch ArpNaks =========================.
2-66 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LANEClient Use LANEClient (local area network emulation client) to allow inband man agement of LANE clients on the switch. Opera tors add, modify, (show client) Parame ters SER VER SV C XX Input Parameter Description V al ue/Field Size Default [ClientNum ber] Number of the client.
SmartCell 6A000/ZX-250 Refere nce Manual 2-67 Console Commands Description Exam ples switch_prompt # add laneclient ClientNumber(0) :100 LanName(ELAN100): ServerType(LECS): ServerAddress() : 39:00:00:00:00:00:11:11:11:11:11:11:11:00:11:22:22:44:55:01 IPAddress() : 101.
2-68 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LECS Use LECS (local area network emulation configur ation server) to manage the operationa l status of the LECS on the networ k. Opera tors start, stop Parame ters This command has n o parameters.
SmartCell 6A000/ZX-250 Refere nce Manual 2-69 Console Commands Exam ples switch_prompt # start lecs NOTICE - 'LECS' ***** LECS started ***** switch_prompt # switch_prompt # stop lecs NOTICE .
2-70 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LECSAddress Use LECSAddress (LAN emulation configur ation server A TM address) to configure addresses on the switch. This address identifies th e LECS on the network that will be contacted for information when LAN emulation is used.
SmartCell 6A000/ZX-250 Refere nce Manual 2-71 Console Commands Exam ples switch_prompt # add lecsaddress LECSAddress : 39:00:00:00:00:00:11:22:33:44:55:66:77:11:22:33:44:55:66:01 switch_prompt # switc.
2-72 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LECSELAN Use LECSELAN (LAN emulation configur ation server emulated LAN) to m anage the LECS entries on th e ELAN. Opera tors add, delete, modify, show Parame ters SER VER SV C X Paramet er Descri ption V alue/Field Size Default [ELANNumber] Number of the ELAN to which LECS belongs.
SmartCell 6A000/ZX-250 Refere nce Manual 2-73 Console Commands Description s Exam ples switch_prompt # add lecselan ELANNumber(0) : 4 ELANName(ELAN004) : LESAddress(39:00:00:00:00:00:00:00:00:00:14:15:00:00:20:D4:14:15:04:02): ELANType(802.
2-74 SmartCell 6A000/ZX-250 Reference Manual Console Com mands switch_prompt # modify lecselan ELANNumber(0) : ELANName(elan1) : LESAddress(39:00:00:00:00:00:00:00:00:00:14:15:00:00:20:D4:14:15:00:02): 39:00:00:00:00:00:00:00:00:00:14:15:00:00:20:D4:14:15:00:04 ELANType(802.
SmartCell 6A000/ZX-250 Refere nce Manual 2-75 Console Commands LECSELANLEC Use LECSELANLEC (LAN emulation configuration server emulated LAN LANE client) to manage the way LANE clients are assigned to a specified ELAN on the LECS.
2-76 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Operat or Paramet ers/Permis sions Description add lecselanlec [LECAddress] < clientatmaddress > [MACAddress/RouteDesc] <clientmacaddress/routedescriptor> [ELANNumber] <elannumber> Administrator Adds a LANE client to an existing ELAN o n the LECS.
SmartCell 6A000/ZX-250 Refere nce Manual 2-77 Console Commands Exam ples switch_prompt # add lecselanlec LECAddress: 39:00:00:00:00:00:00:00:00:00:14:7B:00:00:20:D4:14:7B:00:01 MACAddress/RouteDesc: 0.
2-78 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LECSStat Use LECSStat (LAN emulation configu ration server statistics) to see statistical information about incoming configuratio n req uests to the LECS.
SmartCell 6A000/ZX-250 Refere nce Manual 2-79 Console Commands Parame ters Output Parameter Description [Successful Config uration Reque sts] Numb er of successful configur ation requests. [Bad Conf iguratio n Request s] Number o f bad conf iguratio n reques ts.
2-80 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description Exam ple switch_prompt # show lecsstat Statistics on LECS ===================================================================.
SmartCell 6A000/ZX-250 Refere nce Manual 2-81 Console Commands LECSTL VParam Use LECSTL VParam (LAN emul ation conf iguratio n server t ype, length , and value parameters) to remove a specifi c TL V parameter from the TL V set on the LEC S.
2-82 SmartCell 6A000/ZX-250 Reference Manual Console Com mands switch_prompt # show lecstlvset TlvsetNumber(ALL) : 2 TlvIndex TlvDescription Value =====================================================.
SmartCell 6A000/ZX-250 Refere nce Manual 2-83 Console Commands LECSTL VSet Use LECSTL VSet (LAN emulation configurati on server type, length, and valu e set) to manipulate TL V parameters on the LECS. A TL V set is a collection of TL V parameters associated with an ELAN (emulated LAN).
2-84 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [ArpResponseT i me] Maximum time that the LEC expects a request/response cycle to take. se conds/1- 30 n/a [FlushT imeout] Time l imit on flush re sponse afte r flush requ est h as b een s ent , be fore taking recovery action.
SmartCell 6A000/ZX-250 Refere nce Manual 2-85 Console Commands Description s Operat or Paramet ers/Permis sions Description add lecstlvset [TLVSetNumber] < tlvsetnumber > [ControlTimeout] < c.
2-86 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # add lecstlvset TLVSetNumber[1-32767](1) : 3 ControlTimeout[10-300]() : 200 MaxUnknownFrameCount[1-10]() : 5 Max.
SmartCell 6A000/ZX-250 Refere nce Manual 2-87 Console Commands 3 Max Unknown Frame Time 40 4 VCC Timeout 40000 5 Max Retry Count 2 6 Arp Aging Time 200 7 Forward Delay 20 8 ARP Response Time 20 9 Flus.
2-88 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LECSVCC Use LECSVCC (LAN emulation conf iguration server virtual ch annel connection) to view the VCCs that are waiting to join t he LECS. These VCCs are set u p by the LANE clie nt (or other entity) as p art of the LECS connectio n.
SmartCell 6A000/ZX-250 Refere nce Manual 2-89 Console Commands Exam ple switch_prompt # show lecsvcc VC Type VPI/VCI =========================================== PVC 0/31 PVC 0/33 SVC 0/112 switch_prom.
2-90 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LES Use LES (LAN emulation server) to contr ol the status of the LES and BUS (broad cast and unknown serv er) servers which are co-located. Y o u can control both servers using LES. Opera tors start, stop Parame ters This command has n o parameters.
SmartCell 6A000/ZX-250 Refere nce Manual 2-91 Console Commands LESARP Use LESARP (LAN emulation server address resolution protocol) to see details of the clients registered with the LES. LESARP also gives the MAC (media ac cess control) address of the client.
2-92 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LESClient Use LESClient (LAN emulation s erver client) to determine m a pp ing between LESELANs and th e LANE (LAN emulation) clients that have joined the specified ELAN (emulated LAN). Clients are uniquely identified b y their LECId.
SmartCell 6A000/ZX-250 Refere nce Manual 2-93 Console Commands Description s Exam ples switch_prompt # delete lesclient ELANNumber (0): LECId (0) : 12 Confirm? (y/n) : y switch_prompt # switch_prompt .
2-94 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LESELAN Use LESELAN (LAN emulation server emulated LAN) to manage the pr operties of the specified ELAN maintained by the LES. If the corresponding BUSELAN exists, it should have the same characteristics as the LESELALN.
SmartCell 6A000/ZX-250 Refere nce Manual 2-95 Console Commands Description s Outpu t Paramet er Description [A TM Address] A TM address of the LES on the ELAN.
2-96 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples The followin g example creates ELAN 102 with default parameter s for LES: switch_prompt # add leselan ELANNumber(0) : 102 ELANName(ELAN102) : ConnectMethod(SVC) : ELANType(802.
SmartCell 6A000/ZX-250 Refere nce Manual 2-97 Console Commands The following ex ample resets an ELAN with default parameters: switch_prompt # modify leselan ELANNumber(0) : 102 ELANName(ELAN102) : ConnectMethod(svc) : ELANType(802.
2-98 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LESLECStat Use LESLECStat (LAN emulation server LAN emu lation client statistics) to view details of control traf fic between the LES and its LANE (LAN emulation) clients. Y ou can see information on all or specified clients that are on that specified ELAN (emulated LAN).
SmartCell 6A000/ZX-250 Refere nce Manual 2-99 Console Commands Description Exam ples switch_prompt # show leslecstat ELANNumber(0) : LECId(0) : 3 Client 3 statistics for ELAN ELAN000 =================.
2-100 SmartCell 6A000/ZX-250 Reference Manual Console Com mands LESStat Use LESStat (LAN emulation server statistics) to manage the statistics that the LES maintains for each ELAN. Opera tors show, clear Parame ters SER VER SV C X Input Parameter Description V alue/Field Size Default [ELANNumber] Number of ELAN to which the LES belongs.
SmartCell 6A000/ZX-250 Referen ce Manual 2-101 Console Commands Description s [Reg. duplicate A TM destination errors] Duplicate A TM address errors for reg ister request. [Join insu f ficient resour ce errors] Insufficient res ources to grant errors for join re quest.
2-102 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # show lesstat ELANNumber(ALL) : 102 ELAN : ELAN102 Statistics Join OK : 0 Join version not supported errors : 0 Reg. version not supported errors : 0 UnReg. version not supported errors : 0 Join invalid request param errors : 0 Reg.
SmartCell 6A000/ZX-250 Referen ce Manual 2-103 Console Commands Lo g Use Log to contro l log message record ing onto the log message buf fer . Opera tors start, stop Parame ters This command has n o parameters. Jus t type start log or stop log at the switch prompt.
2-104 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Lo g AlarmMask Use LogAlarmMask to determ in e—by setting mask in g flags—which log messag es generate alarms. Opera tors modify, show Parame ters For more options see [FilterFlags] input parameter u nder “LogT race”.
SmartCell 6A000/ZX-250 Referen ce Manual 2-105 Console Commands Description s Exam ples switch_prompt # modify logalarmmask Emergency(n): y Alert(n) : Critical(n) : Error(n) : Warning(n) : y Notice(n).
2-106 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Lo g Buf fer Use LogBuf fer if y ou want to record you r messages on the log mes sage buf fer . Opera tors modify, show, clear Parame ters SER VER SV C XX Input Parameter Des cription V alue/Field Size Default [LogBuf ferSize] Size of the message log buf fer in the switch memory .
SmartCell 6A000/ZX-250 Referen ce Manual 2-107 Console Commands Description s Exam ples switch_prompt # modify logbuffer LogBufferSize(10240): 7000 switch_prompt # switch_prompt # show logbuffer Index.
2-108 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Lo g Buf ferSize Use LogBuff erSize to determine the size o f the log buf fer . Opera tor show Parame ter Description Exam ple switch_pr.
SmartCell 6A000/ZX-250 Referen ce Manual 2-109 Console Commands Lo g Print Use LogPrint to print log messages on the console. Opera tors modify, show Parame ters Description s SER VER SV C XX Input Parameter Des cription V alue/Field Size Default [Logpri nt] Enables or disabl es printi ng of log mess ages to the cons ole.
2-110 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # modify logprint LogPrint(OFF) : on switch_prompt # switch_prompt # show logprint Printing Log Messages on Cons.
SmartCell 6A000/ZX-250 Referen ce Manual 2-111 Console Commands Lo g Tr a c e Use LogT race to control filtering and configuration parameters for logging and tracing messages.
2-112 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [Filter Parm V al] User-specified parameter value. Log trace filters messages so that only those with a parameter equal to the specified v alue are printed. Use in conjunction with [Filter Parm Pos] to iden tify in which position the parameter value sho uld appear .
SmartCell 6A000/ZX-250 Referen ce Manual 2-113 Console Commands [Quiet mode] Suppresses the printing of messages to the console but continues to fo rward messages to clients. ON/ OFF ON [Start record] Starting record for message range. Lo g trace prints messages within specified range.
2-114 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Notice messages o n ly 3 2 Information me s sages only 64 Debug mess ages only 128 T race messages only 256 Alarm messages.
SmartCell 6A000/ZX-250 Referen ce Manual 2-115 Console Commands show logtrace All Displays the parameters of the currently configured log trace. Logged messages can also g enerate alarms, dependin g on how the log alarm mask is config ured.
2-116 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # modify logtrace LocalPortNum(6005) : LogBufferSize(1000) : 1300 OutputType(ascii) : EndRecordNum(-1) : FilterM.
SmartCell 6A000/ZX-250 Referen ce Manual 2-117 Console Commands CONS Console specific HW Hardware specific ILMI ILMI mod ule IPSR IP over A TM Server LEC Lan Emulation Client LECS Lan Em ulation Conf .
2-118 SmartCell 6A000/ZX-250 Reference Manual Console Com mands MODU LE ID - BE BEAR Br idged Ethern et Address Resoluti on Pro tocol fu nctions BECF Bridged Ethernet Co nfigurat ion sp ecific MODUL E.
SmartCell 6A000/ZX-250 Referen ce Manual 2-119 Console Commands MODU LE ID - ILMI ILMN Main function s IMSC Miscellaneo us functions ITMR T imers MSGH Message handl ers POR T Port fun c tio ns REQ Req.
2-120 SmartCell 6A000/ZX-250 Reference Manual Console Com mands MODU LE ID - LEC CTL C ontrol spec ific DA T A Data specific DEF Default Message ERR Errors ILMC ILMI specific INIT Initialization IP A .
SmartCell 6A000/ZX-250 Referen ce Manual 2-121 Console Commands MODULE ID - LECS CSIL ILMI functions CSIN Initialization fun c tio n CSSG Signa ling func tions CSTM T imer functio ns CSUT Utilities fu.
2-122 SmartCell 6A000/ZX-250 Reference Manual Console Com mands MODU LE ID - LES MIBS MIB specific PROT Prototype specific SIGS Sign alin g specific SMN Main f unctions SMSC Miscellaneous VLAN VLAN sp.
SmartCell 6A000/ZX-250 Referen ce Manual 2-123 Console Commands MODUL E ID - S IG QS31 QSAAL3.1 specific Q293 Q.2931 sign alin g MODUL E ID - S YS FILE Flash file system related SAAL A TM Adaptati on .
2-124 SmartCell 6A000/ZX-250 Reference Manual Console Com mands MyNMAddr Use MyNMAddr (m y network m anagement add ress) to manage the s witch thr ough the sp ecified IP address. Opera tors modify, show Parame ters Description s SER VER SV C XX Paramet er Description V alue/Field Size Default [IP Addr] IP address of the switch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-125 Console Commands Exam ples switch_prompt # modify mynmaddr IpAddr() : 204.95.75.186 My Nm IP-Address : 204.
2-126 SmartCell 6A000/ZX-250 Reference Manual Console Com mands NetPrefix Use NetPrefi x to manip ulate netw ork A TM address prefixes on a particul ar port. Thi s 13-byt e net prefi x is based on a hierarchical addressing scheme. The default value starts with the first by te being set to 39 (DCC address f ormat), followed b y nine p airs o f 00s.
SmartCell 6A000/ZX-250 Referen ce Manual 2-127 Console Commands Exam ples switch_prompt # modify netprefix PortNumber(ALL) : a1 NetPrefix(39:00:00:00:00:00:00:00:00:00:20:D4:14:15:00): 39:00:00:00:00:.
2-128 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Passwd Use Passwd (password) to chan ge the password of the current or lower-privileged u ser .
SmartCell 6A000/ZX-250 Referen ce Manual 2-129 Console Commands Pin g Use Ping to test I P (internet p rotocol) co nnectivity of a clien t. However , the client must be on t he same su bnet or be reachable by routing from the subnet that is pinging . Opera tor start Parame ters Description Exam ple switch_prompt # start ping DestIP() : 204.
2-130 SmartCell 6A000/ZX-250 Reference Manual Console Com mands PortAutoDetect Use PortAutoDetect to manage the automatic-detection features of the switch on an individual port basis.
SmartCell 6A000/ZX-250 Referen ce Manual 2-131 Console Commands Description s Exam ples switch_prompt # modify portautodetect AutoDetectType(ALL) : sigtype PortNumber(ALL) : a1 Value(on) : off switch_.
2-132 SmartCell 6A000/ZX-250 Reference Manual Console Com mands PortConfi g Use PortConf ig (p ort configu ration) to man age the con figuratio n of a port on the swit ch. Opera tors modify, show Parame ters SER VER SV C XX Input Parameter Des cription V alue/Field Size Default [PortNumber] Port number on the s witch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-133 Console Commands [Port QSAAL State] Signaling AAL (A TM adaptation layer). Indicates if the SSCOP (service specific connection oriented pro tocol) link is up or down. UP , DOWN UP [Port Operational State] State of the link, based on port status ( set by internal p rotocols).
2-134 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # modify portconfig PortNumber(A1) : MaxVPIBits(0) : MaxVCIBits(12) : InterfaceAddressType(PRIVATE) : switch_prompt # [Current VCI Bits] Current VCI bits are d erived fr om the VPI/VCI set closest to the configured, as well as active, VPI/VCI sets.
SmartCell 6A000/ZX-250 Referen ce Manual 2-135 Console Commands The foll owing ex amples sh ow the por t conf iguration of all ports , port A4, and then por t B4 (CPU port ): switch_prompt # show port.
2-136 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Current VPI Bits : 0 Current VCI Bits : 12 Current In Use VCCs : 24 Port B4(CPU) Configuration Current Max VCCs : 4096 switch_prompt # s.
SmartCell 6A000/ZX-250 Referen ce Manual 2-137 Console Commands PortMode Use PortMode to control the port framing proto col on the switch when communicating with other switches that use dif ferent st andards (such as the Eur opean SDH ty pe).
2-138 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Parame ters Description s Input Parameter Des cription Field Size/V alue Default [PortNumber] Port number on the s witch. ALL, A1...A4, B1...B4, C 1...C4, D1...D4 ALL [PortMo de] Phys ical mode t ype of th e port.
SmartCell 6A000/ZX-250 Referen ce Manual 2-139 Console Commands Exam ples switch_prompt # modify portmode PortNumber(ALL) : a1 PortMode(SONET) : sdh switch_prompt # switch_prompt # show portmode PortN.
2-140 SmartCell 6A000/ZX-250 Reference Manual Console Com mands PortStat Use PortStat (port statistics) to manag e traffic statistics for a given port or all ports. These statistics relate to network reso urces managemen t, congest ion, an d performance i ssues.
SmartCell 6A000/ZX-250 Referen ce Manual 2-141 Console Commands Description s Exam ples switch_prompt # show portstat PortNumber(ALL) : Port ID OAM RM CLP1 Unk VC CLP1 Total Recvd Recvd Recvd Dropped .
2-142 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Unknown VC Cells Dropped : 0 CLP1 Cells Dropped : 0 Total Cells Dropped : 0 Port A3 Statistics =========================================.
SmartCell 6A000/ZX-250 Referen ce Manual 2-143 Console Commands PortT raf ficCon g estion Use PortT raf ficCongestion (p ort traffic c ongestion) to m anage traff ic congestion par ameter for the specified port.
2-144 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # modify portrafficcongestion Port(ALL) : Queue1MinimumCellCounter(0) : 40 Queue2MinimumCellCounter(0) : 40 Queu.
SmartCell 6A000/ZX-250 Referen ce Manual 2-145 Console Commands Privile g e Use Privilege to man a ge th e privilege level of the current u ser . Opera tors show, enable, disable Parame ter Description s SER VER SV C XX Input Parameter Description V alue/Field Size Default [Passwor d] Current pas sword for t hat pri vilege le vel.
2-146 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # show privilege The current user is Administrator switch_prompt # switch_prompt # enable password: ******** swi.
SmartCell 6A000/ZX-250 Referen ce Manual 2-147 Console Commands Prompt Use Prompt to control h ow the swit ch prompt i s display ed on the console moni tor .
2-148 SmartCell 6A000/ZX-250 Reference Manual Console Com mands PVC Use PVC (p ermanent vi rtual ci rcuit) to manage PVCs on sp ecific por ts configu red on the switch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-149 Console Commands In the Output P arameter table below , (</d>) appears next to the parameter that is avail able only throug h the show pvc /d (detailed) comman d. When (</s>) appears next to a parameter , the parameter appear s in both the summar ized table and the detailed table.
2-150 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [Low to High Operational Status] (< /d >) Status of the forward connection . Status is from th e low-to-high VC L (virtual channel link)—th e connection between ho st and s witch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-151 Console Commands [Number of EPD Packets dropp ed in th e Fwd Direction] (< /d >) Number of EPD (early packet discard) packets dro pped in the forward dir ection of this cross-connect. Updated every 40 s econds.
2-152 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Operat or Paramet ers/Permis sions Description add pvc [ConnType] < connectiontype > [LowPort] < lowport > [Lo.
SmartCell 6A000/ZX-250 Referen ce Manual 2-153 Console Commands Y ou can create either a P TP (poi nt-to-point ) or PMP (p oint-to- multipoin t) PVC when you defin e the ports and low identifiers [vci] and [vpi ]. T o send traffic fr om one port to multiple p orts, enter the same low port and low identifiers fo r all the PVCs at a single port.
2-154 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Standard Repo rt switch_prompt # show pvc d2 CrossConnId :( ALL ): Conn Conn Traffic Conn Low High Admin Id SubId Type Type Port Vpi/Vci.
SmartCell 6A000/ZX-250 Referen ce Manual 2-155 Console Commands Detailed Report for One Port ( [/d b2] ) switch_prompt # show pvc /d b2 CrossConnectId(ALL) : Show Cross Connection in Detailed Mode ===.
2-156 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Backward Traffic Type : NRTVBR Backward Bandwidth Allocated in Kb/s : 411 Backward Priority Queue : MEDIUM-LOW Bkwd Early Packet Discard.
SmartCell 6A000/ZX-250 Referen ce Manual 2-157 Console Commands PVCByID Use PVCBy ID (permane nt virtu al circuit by identi fication number) t o manage cr oss-conn ect based P VCs on a cross-co nn ect ID or sub ID.
2-158 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # activate pvcbyid CrossConnId(0) : 4097 CrossConnSubId(0) : 2061 switch_prompt # switch_prompt # delete pvcbyid.
SmartCell 6A000/ZX-250 Referen ce Manual 2-159 Console Commands Reboot Use Reboot to reboo t the switch. Enter Reboot with caution as it is instantly entered with ou t offering the chance to confirm your deci sion. Opera tor reboot Parame ters This comman d has no par ameters .
2-160 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ple switch_prompt # reboot Luxor Start-up Code Version 1.0.0, Nov 13 1996 Copyright 1995, ZeitNet Inc. CPU Board Details: Board Revision: 1 CPU Speed: 25 MHZ. Common DRAM Base Address: e0000000, Size: 8 MB.
SmartCell 6A000/ZX-250 Referen ce Manual 2-161 Console Commands Route Use Route t o administ er IP (int ernet protoco l) route man agement to an A TM client through an Ethernet network. It allows network managemen t software to communicate acro ss a network of switches.
2-162 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # add route DestNetIP() : 204.95.77.187 GatewayIP() : 204.
SmartCell 6A000/ZX-250 Referen ce Manual 2-163 Console Commands Rows Use Rows to alter the number of rows per pag e on the consol e display . Opera tor modify Parame ter Description Exam ple switch_pr.
2-164 SmartCell 6A000/ZX-250 Reference Manual Console Com mands SARStat Use SARStat (s egmentation and reassembly statistics) to view statistics from the SAR on the CPU port. This is useful for de bugging har d ware problems. Opera tor show Parame ters This command has no inpu t p arameters.
SmartCell 6A000/ZX-250 Referen ce Manual 2-165 Console Commands Description [ISR Int] T otal interrupts received. [RQU Int] R eceive qu eue underrun indicator since last u p-time or clear . [RQA Int] Receive queue alert indicator since last up -time or clear .
2-166 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ple switch_prompt # show sarstat Receive Statistics Rcv Pkts: 6 Rcv Byts: 648 Raw Cell: 0 Buf UF : 0 FIFO OR : 0 Max Len : 0 Len Er.
SmartCell 6A000/ZX-250 Referen ce Manual 2-167 Console Commands Shutdown Use Shutdown to shut down the switch to a state where it can be powered of f. It stops all log ging and synchronizes the file system. This must be run befo re turning off the switch.
2-168 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Si g Confi g Use SigCo nfig (s ignaling configur ation) t o manage si gnaling config uration of all or specif ic por ts. Opera tors modify, show Parame ters SER VER SV C XX Input Parameter Des cription V alue/Field Size Default [PortNumber] Port number on the s witch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-169 Console Commands Description s Exam ples switch_prompt # modify sigconfig PortNumber(A1) : A2 CurrentInterfaceType(UNI3.0) : UNI3.1 CurrentInterfaceRole(NETWORK) : USER DefaultInterfaceType(UNI3.0) : UNI3.
2-170 SmartCell 6A000/ZX-250 Reference Manual Console Com mands The followin g examples are for a specific port - A2, and then for all p orts: switch_prompt # show sigconfig a2 PortNumber : A2 Current Signaling Type : UNI3.1 Current Signaling Role : NETWORK Default Signaling Type : UNI3.
SmartCell 6A000/ZX-250 Referen ce Manual 2-171 Console Commands Si g Fla g s Use SigFlags (signaling flags) t o view the status of flags related to s ignaling.
2-172 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Si g Stat Use SigStat (signa lin g statistics) to see current sig nal ing statistics of all ports or a specific port. Opera tor show Parame ters SER VER SV C XX Input Parameter Description V al ue/Field Size Default [PortNumber] Port n umber on the switch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-173 Console Commands Description [Emit Signal ing Message Errors] N umber of signal ing message er rors for thi s switch (su ch as invali d informatio n elements (IE) or missing mand atory elements in the IEs).
2-174 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ple switch_prompt # show sigstat PortNumber(ALL) : a2 Signaling per Port Statistics ===============================================.
SmartCell 6A000/ZX-250 Referen ce Manual 2-175 Console Commands SSCOPConfi g Use SSCOPC onfig (serv ice-specific con nection- oriented pr otocol conf iguration ) to view t imers and other parameter values. Opera tor show Parame ters SER VER SV C XX Paramete r Description V alue/Field Size Default [Port#] Port number on the switch.
2-176 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description Exam ples switch_prompt # show sscopconfig PortNumber(ALL) : A1 Port# MaxPD MaxCC PollTm KpAliveTm NoRespTm CCTm TxWindowSz .
SmartCell 6A000/ZX-250 Referen ce Manual 2-177 Console Commands SVC Use SVC (switched virtual circuit) to see the SVCs cre ated on the switch. Opera tor show Parame ters In the Output Paramete r table below , (< /d >) appears next to parameters that are available only through the show sv c /d (detailed) comman d.
2-178 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [ConnT ype] (< /s >) Either PMP to P TP connection type. PMP , P TP [LowPort] (< /s >) [LowVPI] (< /s >) [LowVCI] (<.
SmartCell 6A000/ZX-250 Referen ce Manual 2-179 Console Commands [FwdRMCellP riority] (< /d >) Forward RM (res ource management) cell priority for this cross-connect, as calculated by CAC. Enabled, Disabled Fwd Cell Loss Prio rity (CLP)] (< /d >) Forward bandwidth allocated to th is cross-connect, as calculated by CAC.
2-180 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples The following ex amples show a summarized and detailed listing of a n SVC.
SmartCell 6A000/ZX-250 Referen ce Manual 2-181 Console Commands Detailed Report ( </d> ) switch_prompt # show svc /d PortNumber(ALL) : CrossConnectId(ALL) : Show cross-connection in Detailed Mod.
2-182 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Switch Use Switch to backup and restore switch configuration files. Opera tors backup, restore Parame ters SER VER SV C XX Input Parameter Description V al ue/Field Size Default [ServerIP] IP address of the backup server .
SmartCell 6A000/ZX-250 Referen ce Manual 2-183 Console Commands Description s Exam ples switch_prompt # backup switch ServerIP(1.1.1.200) : 1.1.1.200 Path(public/smartcell.ztr) : /back_dir/cnfg_wk04 switch_prompt # switch_prompt # restore switch ServerIP() : 1.
2-184 SmartCell 6A000/ZX-250 Reference Manual Console Com mands SwitchConfi g Use SwitchCo nfig (switch configu r atio n) to manage switch - related parameters, lik e switchname and IP address. Opera tors modify, show Parame ters SER VER SV C XX Input Parameter Description V alue/Field Size Default [SwitchName] Name of the switch.
SmartCell 6A000/ZX-250 Referen ce Manual 2-185 Console Commands [Common DR AM] Co mmon DRAM memory size. megabyt es/Up to 4 characters [SAR Control SRAM] SAR control memory size.
2-186 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [Build Dat e] The date which th e code was loaded on the switch. day/mo n th/date/ hr :m in:sec year [Software Image Size] Binary imag e size. bytes [Heap Space Used/T otal/%Free] T otal heap space used, total memo ry allocated to heap, and percent of free memory .
SmartCell 6A000/ZX-250 Referen ce Manual 2-187 Console Commands Description s Exam ples switch_prompt # modify switchconfig SwitchName(switch_1) : switch_2 IPAddress(200.
2-188 SmartCell 6A000/ZX-250 Reference Manual Console Com mands SwitchName Use SwitchName to change the nam e of the switch. Opera tor modify Parame ter Description Exam ple switch_prompt # modify swi.
SmartCell 6A000/ZX-250 Referen ce Manual 2-189 Console Commands SwitchT raf ficCon g estion Use SwitchT raf ficCongestion to manage glo bal switch traffic con gestion thresholds on the switch.
2-190 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # modify switchtrafficcongestion Queue1EFCIThreshold(16383) : 2000 Queue2EFCIThreshold(16383) : 20.
SmartCell 6A000/ZX-250 Referen ce Manual 2-191 Console Commands T raf ficDescriptor Use T rafficDescriptor to manage the templates that describe traf fic characteristi cs of a VC (virtual circuit) that are u sed in the creation of PVCs (permanent virtual circuits.
2-192 SmartCell 6A000/ZX-250 Reference Manual Console Com mands [SCRCLP0] Specifies maximu m average rate at which cells can be sent over a VC. SCR of cells with their CLP bit equa ls zero. Kb/s/ 0-622 000 0 [MBSCLP01] MBS (maximum burst size) of cells with their CLP set to one.
SmartCell 6A000/ZX-250 Referen ce Manual 2-193 Console Commands Description s Exam ples The following example creates a traf fic descriptor of type 4. After the traf fic descriptor is created, it is listed in a table and associated with an index number .
2-194 SmartCell 6A000/ZX-250 Reference Manual Console Com mands switch_prompt # add trafficdescriptor TrafficType(UBR) : cbr TrafficDescriptorType(8) : 4 PCRCLP01(0) : 180 PCRCLP0(0) : 155 SCRCLP01(0).
SmartCell 6A000/ZX-250 Referen ce Manual 2-195 Console Commands 4 -W ith CLP and T a gging, but no SCR. CBR, NR TVBR, RT V B R pcrclp 0, pcrclp 01 1 Evaluat es cells set with CLP=1 and cells set w ith CLP=0 separately . Because tag option is set, non-compl iant CLP=0 cells are tagg e d and non-compl iant CLP=1 cells are dropped.
2-196 SmartCell 6A000/ZX-250 Reference Manual Console Com mands.
SmartCell 6A000/ZX-250 Referen ce Manual 2-197 Console Commands T rapCommuni ty Use T rapCommuni ty to manage th e list of hosts that the switch sends trap notificatio ns to concerning si gnificant events. Each trap co mmunity has a n ame, IP address, and po rt number .
2-198 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Description s Exam ples switch_prompt # add trapcommunity Name() : boris IpAddr() : 204.
SmartCell 6A000/ZX-250 Referen ce Manual 2-199 Console Commands T rustedNMS Use T rus tedNMS (tr usted network man agement syst em) to config ure a “trust ed network management system” on the switch. The trusted NMS is identified by its IP address.
2-200 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Parame ters Description s Exam ples switch_prompt # modify trustednms IpAddr() : 90.1.1.1 Trusted NMS IP-Address : 90.1.1.1 switch_prompt # switch_prompt # show trustednms Trusted NMS IP-Address : 90.
SmartCell 6A000/ZX-250 Referen ce Manual 2-201 Console Commands UNIRoute Use UNIRoute (user-network interface ro ute) to manage UNI routes and UNI routing tables. The routes are static using this command, com pared to the dyn amic UNI routes created th rough ILMI reg istration.
2-202 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # add uniroute PortNumber(A1) : a3 UNIATMAddress(): 39:00:00:00:00:00:00:11:22:33:44:55:66:11:22:33:44:55:66:01 .
SmartCell 6A000/ZX-250 Referen ce Manual 2-203 Console Commands The followin g example shows the uniro ute listing, before and after all ports are flu shed: switch_prompt # show uniroute PortNumber(AL.
2-204 SmartCell 6A000/ZX-250 Reference Manual Console Com mands VCCMask Use VCCMask (virt ual chann el connection mask) to mana ge th e combination of VP I (virtual path identifier) bit and VCI (virtual chan nel identifier) bit settings. There are only four different VCC mask entries allowed by the sw itch and the VPI and VCI shift must total 12 .
SmartCell 6A000/ZX-250 Referen ce Manual 2-205 Console Commands Exam ples switch_prompt # modify vccmask MaskIndex(0) : 0 VPIShift(0) : 3 VCIShift(12) : 9 switch_prompt # switch_prompt # show vccmask .
2-206 SmartCell 6A000/ZX-250 Reference Manual Console Com mands W e llKnownAddre ss Use W ellKnownAddress to manage the m apping between the A TM forum defined wel l-kno wn address fo r t he LEC S (LAN emulation conf iguration server ) and a registered address for another LECS.
SmartCell 6A000/ZX-250 Referen ce Manual 2-207 Console Commands Description s Operat or Parameters/P ermissions Descr iption add wellknownaddress [WellKnownAddress] < clientatmaddress > [RegisteredAddress] < serveratmaddress > Administrator Maps well-known address to the r egistered address of the server .
2-208 SmartCell 6A000/ZX-250 Reference Manual Console Com mands Exam ples switch_prompt # add wellknownaddress WellKnownAddress(47:00:79:00:00:00:00:00:00:00:00:00:00:00:a0:3e:00:00:01:00): RegisteredAddress(39:00:00:00:00:00:00:00:20:D4:14:22:80:00:20:D4:14:22:80:01): 10.
SmartCell 6A000/ZX-250 Reference M anual 3-1 Boot Load Commands 3 BOOT LOAD COMMANDS This chapter describes the low-level boot load commands. Boot load commands are used for setti n g switch start-up behavior and for performin g software downloads.
3-2 SmartCell 6A000/ZX-250 Reference Manual Boot Load Com mands Accessin g the Boot Load Comma nds Boot load commands are execute d from the boot load pro mpt. The boot load prom pt is no t part of the s witch consol e, and is accessible only after a reboot an d before the switch software is loaded.
SmartCell 6A000/ZX-250 Reference M anual 3-3 Boot Load Commands chpi Use chpi to set one of the two boot load so ftware images as the default. Unl e ss o therwise specified withi n the initial reboot coun tdown, the default b oot load software image is the image that is loaded into DRAM and executed.
3-4 SmartCell 6A000/ZX-250 Reference Manual Boot Load Com mands clfs Use clfs to clear the switch flash file system. The clfs command clears all VLAN and ELAN con figurations, route defini tions, p ort sett ings, and P VC configu rations. clfs also clears all IP addr esses, including the IP address for th e switch Ethernet interface.
SmartCell 6A000/ZX-250 Reference M anual 3-5 Boot Load Commands dcf g Use dcfg to display information ab ou t the current boot PROM configuratio n • Revision numbers of both boot load software image.
3-6 SmartCell 6A000/ZX-250 Reference Manual Boot Load Com mands df Use df (do wnload firmware) to do wnload software images from a TF TP/Bootp server to the flash RAM of the switch. The df comm and uses three parameters: b , s , and p . These parameters specify which software componen t to download.
SmartCell 6A000/ZX-250 Reference M anual 3-7 Boot Load Commands g o Use the go command to exit the boo t load prompt and run switch software (with or without POST). Exam ple => go s Verifying Checksum of Secondary Flash... Host Name: Attaching network interface ei0.
3-8 SmartCell 6A000/ZX-250 Reference Manual Boot Load Com mands he Use he to get help o n boot load comm a nd s or show list of all b oo t lo ad commands. The ques tion mark ( ? ) can be entered in place of he . Exam ple => he chpi chpi [option] option: 0 .
SmartCell 6A000/ZX-250 Reference M anual 3-9 Boot Load Commands ponf Use ponf to set whether POST diagno st ics are run by default when th e switch is st arted. Exam ple => ponf p Modifying Control/Stat field to execute POST, please wait... New postOnOff value programmed successfully into Control/Stat field.
3-10 SmartCell 6A000/ZX-250 Reference Manual Boot Load Com mands.
SmartCell 6A000/ZX-250 Reference M anual A-1 APPENDIX A ACRONYMS A B AAL A TM Ada ptati on La ye r AAL1 A TM Ada ptati on La ye r T y pe 1 AAL2 A TM Ada pter L a yer T ype 2 AAL3/4 A TM A d apte r L a.
A-2 SmartCell 6A000/ZX-250 Reference Manual Acronym s C BUS Broadcast and Unkno wn Server CAC Call Admiss ion Control CAN Campus Area Net work CA T-3 Category 3 unshielde d twis ted pair cable CA T-5 .
SmartCell 6A000/ZX-250 Reference M anual A-3 Acronyms D E DCC Digital Cross Co nnect, gen eric DACS or Direct Connect Car d, data interfac e module DF Download Fla sh DS-0 Digi tal Si gnali ng 0 DS-1 .
A-4 SmartCell 6A000/ZX-250 Reference Manual Acronym s F G H I FCS Frame Check Se quence FIFO First I n First Out FT P File T ransfer Protoc ol GB/S Gigabits per secon d GCRA Generic Ce ll Rate Al gori.
SmartCell 6A000/ZX-250 Reference M anual A-5 Acronyms J K L I/O Input/Out put IOM Input/Out put Module IP Interne t Protocol IP/A TM Internet Pr otocol ov er A TM IPX Inte rnetwork Pa cket Exc hange p.
A-6 SmartCell 6A000/ZX-250 Reference Manual Acronym s M N LECSELA N LAN Emulation Configur ation Ser ver Emulat ed LAN LES LANE Server LESELAN LANE Server Emul ated LAN LIS Logical I P Subnet work LLC.
SmartCell 6A000/ZX-250 Reference M anual A-7 Acronyms O P NETBEUI NetBI OS Ext ensio n User Interf ace NFS Netw o rk Fi le Sys tem NIC Netwo rk In terfac e Cont roller /Car d NLS Natural L anguage Syn.
A-8 SmartCell 6A000/ZX-250 Reference Manual Acronym s Q R PDU Protocol Data Unit PMD Physic al Media Depe ndent S ub-layer PMP Point -to-Multi point P-NNI Private Network Node I nterfac e or Priva te .
SmartCell 6A000/ZX-250 Reference M anual A-9 Acronyms S RT-VBR Real T ime - V ariable Bit Rate RW Read-W rite Access SAAL Signalin g A TM Adaptation Layer SAR Segment ation An d Reasse mbly SAR-PDU SA.
A-10 SmartCell 6A000/ZX-250 Reference Manual Acronym s T U V T-1 T ran sm issi on Sy st em 1 T-3 T ran sm issi on Sy st em 3 TA X I T ranspar ent Asynchr onous T ransmit ter/Rece iver Int erface TCP T.
SmartCell 6A000/ZX-2 50 Reference Manual A-11 Acronyms W VCC V irtual Channel Connecti on VCI V irtu al Chan nel Id e ntifie r VCL V irtual Channel Link VLAN V irtual LAN VP V irtual Path VPC V irtual.
A-12 SmartCell 6A000/ZX-250 Reference Manual Acronym s.
SmartCell 6A000/ZX-250 Reference M anual B-1 APPENDIX B CAUSE CODES A TM events often generate messages that appear on the console. Most messages are self-explanatory . However , some messages contain additional information in the form of cause codes.
B-2 SmartCell 6A000/ZX-250 Reference Manual Cause Code s 38 Network out of o rder 41 T e mpor a ry failu re 43 Access information discarded 45 No VPI/VCI available 47 Resource unavailable, unspecified.
SmartCell 6A000/ZX-250 Reference M anual B-3 Cause Codes 1 15 No response t o restart request 1 16 Link n ot active 1 17 Lin k not fo und 1 18 Calling p arty number not set.
B-4 SmartCell 6A000/ZX-250 Reference Manual Cause Code s.
SmartCell 6A000/ZX-250 Referen ce Manual C-1 APPENDIX C T ECHNICAL SUPPORT This appen dix tells you what to do i f you need technical sup port for your S martCell ZX-250 switch . Cabletron of fers several s upport and servi ce progr ams that pr ovide hi gh-qua lity supp ort to our cust omers.
C-2 S martCell 6A000/ZX-250 Reference Manual Technical Support Detailed d escrip tion o f the iss ue (inclu ding hi story , what you 've tried, and condi tions un der which you see this o ccu.
SmartCell 6A000/ZX-250 Reference Manual I-1 INDEX A AALType ............... .................. ............ 2-192 Abbrev iations .................................... ....... 1-3 Access Den ied .......................... .............. 2-79 accessi ng boot lo ad commands .
I-2 SmartCell 6A000/ZX-250 Reference Manual Index C CACParams swit ch attr ibute ..... 2-20 to 2-21 CACStat swi tch attr ibute ........... 2-22 to 2-23 cause co des AAL para meters cannot be suppo rted ..... ........................... ........... B-2 Access i nformat ion di scarded .
SmartCell 6A000/ZX-250 Reference Manual I-3 Index Cont rolTi meout ............... ....................... 2-83 conventi ons ............ ........................... ....... 1-2 Count ............................... .................. ... 2-129 CPE Int .
I-4 SmartCell 6A000/ZX-250 Reference Manual Index F FIFO OR ............ ........................... ........ 2-164 Filte r Debu g Lv l ................................... 2-112 Filter Fl ags .................. .................. ........ 2-113 Filter Message Id .
SmartCell 6A000/ZX-250 Reference Manual I-5 Index L2HOpSta tus ..................................... ... 2-178 LAN Name ...................... .............. 2-24, 2-66 LAN Type ........................... 2-25 , 2-42 , 2- 95 LEC Configs ........... .
I-6 SmartCell 6A000/ZX-250 Reference Manual Index Out Oc tets ............................ ................... 2-18 Out Unicas t ................................... .......... 2-18 Output Des tinatio n ............................... 2-112 Output Typ e .
SmartCell 6A000/ZX-250 Reference Manual I-7 Index SPE Int ................... .................. ............ 2-165 spur In t ............................ .................. ... 2-164 Start r ecord ...................... .................. ... 2-113 Start FileNu m .
I-8 SmartCell 6A000/ZX-250 Reference Manual Index.
An important point after buying a device Cabletron Systems 6A000/ZX-250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cabletron Systems 6A000/ZX-250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cabletron Systems 6A000/ZX-250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cabletron Systems 6A000/ZX-250 you will learn all the available features of the product, as well as information on its operation. The information that you get Cabletron Systems 6A000/ZX-250 will certainly help you make a decision on the purchase.
If you already are a holder of Cabletron Systems 6A000/ZX-250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cabletron Systems 6A000/ZX-250.
However, one of the most important roles played by the user manual is to help in solving problems with Cabletron Systems 6A000/ZX-250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cabletron Systems 6A000/ZX-250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
