Instruction/ maintenance manual of the product DFTA46R Bush
Go to page of 26
INSTRUCTION MANUAL Toll Free Warranty and Service: 1800 509 394 The Gold T echnical Support Line: 1902 215 259 (Charges will apply at $2.95 per minute for gold technical support only) DFTA46R High Def.
Important Safety Instructions Disclaimer Information in this document i s subject t o change without n otice. The manufacturer does not m ake any representations or warranties (implied or otherwise) r.
The symbol indicates that dangerous voltages constituting a risk of electric shock are present within this unit. The symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
Thank you for buying this Bush product, which is designed to give you many years of t rouble-free service. Yo u may already be familiar with using a similar unit, b ut please take time to read these instructions. T hey are designed to familiarise you with the unit s m any features and to ensure you get t he very best from your purchase.
A bout the Set T op Box An easy to use on-screen installation guide is provided. In addition, a fully featured Remote Control is included that of fers you access to every feature with a simple press of a button.
Table of Contents Front and Rear Panel .......................................................................... 6 Remote Control...................................................................................7 Connections.........................
Front and Rear Panel 1. Front panel 1 ST ANDBY INDICA TOR: Shows you the power state of the set top box, the LED will turn red if the set top box is in standby mode and Green if it is on. 2 REMOTE CONTROL SENSOR: Used to receive the signal from the remote control.
Remote Control 7 1. LIST : Press the List Button to display your recorded programs list. 2. MUTE: Press the Mute Button to switch off the Sound only. Press again to restore audio output. 3. INFO: Press the INFO Button to display the current channel information.
Installing the Batteries Remove the battery cover from the Remote Control and put 2xAAA size batteries inside the compartment. The diagram inside the Battery Compartment shows the correct way to install the batteries. 1.Open the cover 2.Install batteries 3.
AC 230V ~ 50Hz Connecting to a T elevision Caution: Make sure to check the voltage specification of the wall outlet is the same rating with the receiver . T o prevent the risk of electric shock, do not open the cover or the back of the receiver. Note: When connecting the receiver to other equipment, e.
AC 230V ~ 50Hz TV Aerial 10 Connecting to a DVD Recorder or VCR.
11 Connecting to an Audio System BASS TREBLE ECHO DOWN UP VOLUME INPUT SELECTOR MUTE KARAOKE CHANNEL TEST MODE 3 STEREO PRO LOGIC BYPASS EXCITE POWER MIC 2 1 1 MIC VOL 2 MIC Amplifier Coaxial Coaxial .
12 (1) Select [OSD Language] and (2) Select [Country] and (3) Select [Channel Search] and press RIGHT or OK key to begin Automatic channel search (4) Once channel tuning is complete, Press the Navigate Buttons to select your desired language. Press the Navigate Buttons to select your desired country.
13 (2) Program Edit To edit your program preferences (lock, skip, favourite, move or delete), you will need to enter the Program Edit Menu. This Menu requires a password to access. Enter the default password '000000'. Programme Edit ALL TV Move Skip Lock Delete FAV FAV 001 TV3 003 3/24 004 K3/300 002 33 SKIP Searching.
14 Move a TV or Radio Program/s 1. Select the preferred program then press the RED button. A move symbol will appear 2. Press UP/DOWN to move the program 3. Press OK to confirm 4. Repeat the above steps to move more channels Lock Program/s You can lock selected programs for restricted view.
15 (1). Aspect Ratio You must set the display format to either 4:3 PanScan, 4:3 Letter Box,16:9 Full Screen or 4:3 Full, 16:9 Pillar Box, 16:9 PanScan Auto to get the maximum display when watching TV . (2). Resolution If the video does not appear correctly, change the setting.
16 1 . Auto Search Search and install all channels automatically . This option overwrites all preset channels. 1. Select [Auto Search] and press OK or RIGHT to start channel search. 2. T o cancel channel search, press EXIT . 2. Manual Search Install new channels manually.
17 (8) Time Setting M then M Press UP/DOWN to s s . To access the enu, press MENU select [Time]. The enu provides options to adjust the time settings. elect an option and press RIGHT/LEFT to adjust the setting . Press EXIT to exit the menu (1) Time offset (2) Country Region Select the Country Region when [T ime Offset] is set to Auto.
18 (1) Parental Guidance You can restrict access to channels that are unsuitable for children. To restrict/lock the channel you will need to enter either the default password '000000' or your own password. (2) Set Password Set or change the password for locked programs.
19 (4) Information View model, hardware and software information. (5) Software Update 1.OAD When this option is set to "On", the Set T op Box will begin to search for new software automatically , from over air broadcasts based on your set time in "Start Time".
(2) Photo configure : You can select on of the following settings to for your photo slide show options. -Slide Time: You can adjust slide show interval from 1~8 seconds. -Slide Mode : Y ou can adjust slide show ef fect as mode 0~59 or random. -Aspect Ratio : Y ou can displays the picture as its original aspect.
Time shift Make sure that a USB or Hard Disc Drive device is connected to the receiver in order to be able to use the time shift function. We recommend that you use a powered Hard Disk Drive as USB Sticks will only allow limited functionality. Please ensure that the USB Memory used has a memory capacity of above 2 GB.
22 The image stopped suddenly or mosaic Problem Potential Reasons What to do No picture Power isn't connected Connect the power The power switch is not on Switch on the power Screen shows No Sign.
23 Video Decoder F ormat MPEG4 AV C/H.264 HP@L4 MPEG2 MP@ML.HL Output F ormat 576P, 720P, 1080i,1080P, 4:3 and 16:9 Output P ort HDMI, CVBS Audio Decoder F ormat MPEG-1 (layer1&2) Audio output Dig.
PO BOX 6287, SILVERW ATER NSW 181 1 www.bushaustralia.com.au Bush : 1800 509 394 Australia Bush : 0800 450 259 New Zealand Warranty Warranty Please keep your receipt as proof of purchase. This product is warranted for any defect in materials or workmanship for one year after the original date of purchase.
PO BOX 6287, SILVERW ATER NSW 181 1 www.bushaustralia.com.au.
An important point after buying a device Bush DFTA46R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bush DFTA46R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bush DFTA46R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bush DFTA46R you will learn all the available features of the product, as well as information on its operation. The information that you get Bush DFTA46R will certainly help you make a decision on the purchase.
If you already are a holder of Bush DFTA46R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bush DFTA46R.
However, one of the most important roles played by the user manual is to help in solving problems with Bush DFTA46R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bush DFTA46R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
