Instruction/ maintenance manual of the product G4237/8 Burley
Go to page of 15
BURLEY G423 7 / 8 IM A GE FL UELESS GA S HEA TER INST ALL A TION, SERVICING & US ER INS TRU CTIONS FOR USE IN THE COUNT RIES S T A TED ON THE DA T A PL A TE AND C ART ON WITH NA TUR AL GAS G20 OR .
- 2 - INTRODUCTION Thank you for choosing this b urley product. All of our pro ducts c arry a CE ma rk which is awarded by an i ndependent test house (notified body ) and shows the fires have be en type tested to meet the essential requirements of the European Gas Appliance Directive and the appro priate British Standards.
- 3 - 3. GENERAL REQUIREMENTS 3.1 Gas appliances must be installed i n ac cordance with the rules in f orce. I n the UK it is the law that a ll gas a ppliance s must be i nstalled by a CORGI registered installer, i n ac cordance with the Gas Safety (Installation and U se) re gulations (as amended).
- 4 - 4.2 D ecide upon the route f or the gas supply and if this i s to be a conce aled supply, s elect a suitable hole in the fire box , remove t he knock out an d lay in the s upply as required. F it the rubber grommet aro und the gas pipe entry to the appliance and seal.
- 5 - ensure there is no possibili ty of them touching the appliance . 632mm 197mm 590mm Overall dimensions are as shown. Hearths - Fo r hea rth mounting ( or if the fire is less than 20 0mm above the ground) then the hearth must protrude at least 100mm in f ront of the fire and 50mm to either side.
- 6 - 5.3 METHOD TWO - INSET ON HEAR TH OR INSET WALL MOUNTED This method allows f or the fire to be inset into a wall or fire place opening. The applia nce c ase has a 90mm deep spacer that needs to be remove d and the corr esponding deep bracke ts nee d to be taken off the case.
- 7 - Fixing - The a ppliance should be sec ured to the wall usi ng the fixing bracke ts on t he fla nge of the appliance. If it is to be mo unted above t he ground, c are should be taken to e nsure the wall is a ble to take the we ight of the appliance an d that the fixings are o f the c orrect type.
- 8 - 7.0 REASSEMBLY 7.1 To remove the g lass, remove the 4 nuts i n t he side frame s and pivotin g it out from the bottom remove glass from its top channel . Refitting is done in revers e order. 7.2 REVERSIBLE SIDE CHEEKS The appliance has side c heek s that are plain on one side and bri ck effect on the other.
- 9 - 9.0 TO LIGHT THE HEAT ER BEFORE L I GHTING. IF THE PIPES HAVE N OT BEEN PURGED OF DEBRIS, DO SO NO W BE FORE LIGHTING THE FIRE. FAILURE TO DO SO WILL RESULT IN BLOCKAGES WITHIN THE PILOT. BURLEY A PPLIANCES IS THE ONLY COMPANY TO BENCH RUN AND THOROUGHLY TEST EVERY SINGLE GAS F IRE IT PRODUCES.
- 10 - automatically l ight the pilo t light, mo nitor its sa fety f or about 20 seconds and then it will light the burner on high flame. To alternate between high and low fl ame use the flam e buttons on t he right hand side of the handset. To turn the fire OFF press the ● button on the top left hand side of the remote handset.
- 11 - 10.4 FIREFRO NTS The design of these affec t combustion, therefore only the corr ect front supplied with the appliance may be fitted. 10.5 FIREGUA RDS A fir eguard is not supplied with this app.
- 12 - Light t he fire using the method i n the i nstructions and ensure that the pilot lights consiste ntly an d the pilot flame enve lopes the thermo couple. The pilot should hold in 10 seconds. Turn c ontrol to main burner, this should light smoothly within 10 s econds.
- 13 - This is not a dr yin g appliance. Do no t place clothing or other arti cles, on or ag a inst it. Do not store or use flamm a ble substances on or ne ar the heater. Do not spra y aerosols on or near the heater. If any material, such as plast ic, melts o nto the surface of the glass, turn the heater off and allow it to co ol.
- 14 - To light the fire, f irst ensure the red knob is turned clockwise to OFF . Press the left hand (red) control knob for several seconds then turn slowly a nticlockwise to the ignition position. A click will be heard and the pilot (under right side of fuel bed) should light.
- 15 - CLEANING AND MAIN TENANCE Ensure the appliance is switched off and cooled down before cleaning. The case and surround are best cleaned with a damp cl oth a nd wiped dry to avoid smearing.
An important point after buying a device Burley G4237/8 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Burley G4237/8 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Burley G4237/8 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Burley G4237/8 you will learn all the available features of the product, as well as information on its operation. The information that you get Burley G4237/8 will certainly help you make a decision on the purchase.
If you already are a holder of Burley G4237/8, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Burley G4237/8.
However, one of the most important roles played by the user manual is to help in solving problems with Burley G4237/8. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Burley G4237/8 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
