Instruction/ maintenance manual of the product TB3Q-LP Bunn
Go to page of 11
TB3/TB6 Series Including: TB3; TB3-LP; TB3Q; TB3Q-LP; TB6; TB6Q ST ARTING WITH SERIAL NUMBER: TU00020000 INST ALLA TION & OPERA TING MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFI.
Page 2 41465.1 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
Page 3 #00831.0000 #00656.0001 #03408.0000 #03409.0000 #37881.0000 • FILL WA TER T ANK BEFORE ENERGIZING • DO NOT OVERLO AD CIRCUIT • KEEP AWA Y FROM COMBUSTIBLES • DO NOT DEFORM PLUG OR CORD • FAILURE TO COMPL Y RISKS EQUIPMENT DAMAGE, FIRE OR SHOCK • BREWER ENERGIZED UNLESS UNPLUGGED SEE INSTRUCTIONS W ARNING #06064.
Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. 120V model brewers require 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. "A" model brewers require 2-wire, grounded service rated 220-240 volts ac, 10 amp, single phase, 50 Hz.
Page 5 120V MODELS These brewers must be connected to a cold water system with a minimum 1.0 gpm flow rate, and operating pressure between 20 and 90 psi (138 and 620 kPa) from a ½˝ or larger supply line. A shut-off valve should be installed in the line before the brewer .
Page 6 INITIAL SET -UP (TB3Q/TB3Q-LP/TB6Q ONL Y) CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top cover from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.
Page 7 INITIAL SET -UP (TB3/TB3-LP/TB6 ONL Y) CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Remove the top lid from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.
Page 8 AUTO SWEETENER SET -UP CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top lid and both rear panels. 2. Make sure the brewer water supply is off.
Page 9 ADJUSTING BREW VOLUMES NOTE: Check that the brewer is connected to water supply , the tank is properly filled, and a funnel and server are in place, prior to setting or modifying batch sizes. 1. T o adjust concentrate volume on TB3/TB6 models, and dilution volume on TB3Q/TB6Q models: Modifying batch sizes.
Page 10 OPERA TING CONTROLS A. ON/OFF Switch ON - Placing the switch in the left position allows the start switch to activate a timed brew cycle for three gallons of tea.
Page 11 41465.1 042009 CLEANING CAUTION - CLEAN AND SANITIZE YOUR ICED TEA BREWER DAIL Y DAIL Y : 1. Remove, disassemble and thoroughly clean and sanitize the entire brew funnel. The funnel tip and screen must be free from any tea particles or residue.
An important point after buying a device Bunn TB3Q-LP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn TB3Q-LP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn TB3Q-LP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn TB3Q-LP you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn TB3Q-LP will certainly help you make a decision on the purchase.
If you already are a holder of Bunn TB3Q-LP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn TB3Q-LP.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn TB3Q-LP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn TB3Q-LP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
