EN
Bunn logo
Official user manual

Bunn LCA-2

34 pages·1.9 MB·Beverage Dispenser·PDF·ENDEFRITNLJA
Bunn LCA-2
Table of Contents 80 sections LCA-2 LCA-2 PC · INSTALLATION & OPERATING MANUAL · BUNN-O-MATIC CORPORATION · CONTENTS · … ShowHide
LCA-2 LCA-2 PCp.1INSTALLATION & OPERATING MANUALp.1BUNN-O-MATIC CORPORATIONp.1CONTENTSp.2BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYp.2USER NOTICESp.3ELECTRICAL REQUIREMENTSp.4FIELD WIRING TERMINAL BLOCK DIAGRAMp.4Models without Master ON/OFF Switchp.4Models with Master ON/OFF Switchp.4REDp.4ON/OFF SWITCHp.4BLACKp.4PLUMBING REQUIREMENTSp.5INITIAL SET-UPp.5ELECTRICAL HOOK-UPp.5PLUMBING HOOK-UPp.5SETTING DISPENSER FLOW RATEp.6SELECTING THE CORRECT PUMP TUBINGp.7OPERATING CONTROLS AND INTERFACEp.8BUNN ICED COFFEEp.8AMBIENT UNITp.8INITIAL FILL & HEATp.9FlavorGard™ Featurep.10Rinse Alarm Featurep.10BIB Empty Lockout Featurep.11Brew Temperature Lockout Featurep.11PROGRAMMING THE DISPENSERp.12MENU SCREEN ACTION DESCRIPTIONp.12TANK TEMP XXXp.12TANK TEMP XXX CABINET TEMP XXp.12L DISPENSE RATIOp.12SET LF TUBE SIZEp.121/8 EXIT 3/16p.12R DISPENSE RATIOp.12SET RT TUBE SIZEp.12FLAVOR GUARD ?p.12NO EXIT YESp.12LF TASTE OK ? NO EXIT YESp.12FIND LF TARGET PULL DISPENSEp.12RT TASTE OK ? NO EXIT YESp.12FIND RT TARGET PULL DISPENSEp.12LOCK FLAVOR ?p.13EXIT YESp.13FLAVORS LOCKEDp.13NONEp.13EXITp.13LF DISP VOLUMEp.13RT DISP VOLUMEp.13LF DISP VOLUME 1p.13LF DISP VOLUME 2p.13RT DISP VOLUME 1p.13RT DISP VOLUME 2p.13WATER DISP VOL 1p.13WATER DISP VOL 2p.13TANK TEMP 180p.14(-) EXIT (+)p.14READY TEMP 175p.14CABINET TEMP 65p.14LF PRODUCT DISPp.14.0GAL RESET?p.14.0GALp.14RT PRODUCT DISPp.14ENTER PASSWORDp.14SET PASSWORD ?p.14SELECT UNITS ENG EXIT METRICp.14CHILLED UNIT ? NO EXIT YESp.14RINSE ALARM ?p.14RINSE LOCKOUT ?p.15BIB EMPTY LOCKOUTp.15BREW LOCKOUT ?p.15DLY REPEAT DISPp.15(-) 0 SEC (+)p.15CAL LEFT SIDE ?p.15CAL LEFT PUMP ?p.15PULL DISPENSEp.15CAL LF PUMP VOLp.15CAL LF WTR FLOW ?p.15PULL DISPENSERp.15CAL LF WTR VOL (-) 36.0OZ (+)p.15
Page 1 of the Bunn LCA-2 user manual — BUNN-O-MATIC CORPORATION
Page 1 · click to enlarge
Page 1

LCA-2 LCA-2 PC

Bunn LCA-2 — LCA-2 LCA-2 PC diagram (page 1)
Fig. 1
Bunn LCA-2 — LCA-2 LCA-2 PC diagram (page 1)
Fig. 2

INSTALLATION & OPERATING MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644

To obtain the Illustrated Parts Catalog, visit the Bunn-O-Matic website, at www.bunn.com This is absolutely FREE, and the quickest way to obtain the catalog. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.

www.bunnomatic.com 34766.0000J 01/07 ©2002 Bunn-O-Matic Corporation

Page 2 of the Bunn LCA-2 user manual — Table of Contents
Page 2 · Contents
Contents

Contents

LCA-2 LCA-2 PCp.1INSTALLATION & OPERATING MANUALp.1BUNN-O-MATIC CORPORATIONp.1CONTENTSp.2BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYp.2USER NOTICESp.3ELECTRICAL REQUIREMENTSp.4FIELD WIRING TERMINAL BLOCK DIAGRAMp.4Models without Master ON/OFF Switchp.4Models with Master ON/OFF Switchp.4REDp.4ON/OFF SWITCHp.4BLACKp.4PLUMBING REQUIREMENTSp.5INITIAL SET-UPp.5ELECTRICAL HOOK-UPp.5PLUMBING HOOK-UPp.5SETTING DISPENSER FLOW RATEp.6SELECTING THE CORRECT PUMP TUBINGp.7OPERATING CONTROLS AND INTERFACEp.8BUNN ICED COFFEEp.8AMBIENT UNITp.8INITIAL FILL & HEATp.9FlavorGard™ Featurep.10Rinse Alarm Featurep.10BIB Empty Lockout Featurep.11Brew Temperature Lockout Featurep.11PROGRAMMING THE DISPENSERp.12MENU SCREEN ACTION DESCRIPTIONp.12TANK TEMP XXXp.12TANK TEMP XXX CABINET TEMP XXp.12L DISPENSE RATIOp.12SET LF TUBE SIZEp.121/8 EXIT 3/16p.12R DISPENSE RATIOp.12SET RT TUBE SIZEp.12FLAVOR GUARD ?p.12NO EXIT YESp.12LF TASTE OK ? NO EXIT YESp.12FIND LF TARGET PULL DISPENSEp.12RT TASTE OK ? NO EXIT YESp.12FIND RT TARGET PULL DISPENSEp.12LOCK FLAVOR ?p.13EXIT YESp.13FLAVORS LOCKEDp.13NONEp.13EXITp.13LF DISP VOLUMEp.13RT DISP VOLUMEp.13LF DISP VOLUME 1p.13LF DISP VOLUME 2p.13RT DISP VOLUME 1p.13RT DISP VOLUME 2p.13WATER DISP VOL 1p.13WATER DISP VOL 2p.13TANK TEMP 180p.14(-) EXIT (+)p.14READY TEMP 175p.14CABINET TEMP 65p.14LF PRODUCT DISPp.14.0GAL RESET?p.14.0GALp.14RT PRODUCT DISPp.14ENTER PASSWORDp.14SET PASSWORD ?p.14SELECT UNITS ENG EXIT METRICp.14CHILLED UNIT ? NO EXIT YESp.14RINSE ALARM ?p.14RINSE LOCKOUT ?p.15BIB EMPTY LOCKOUTp.15BREW LOCKOUT ?p.15DLY REPEAT DISPp.15(-) 0 SEC (+)p.15CAL LEFT SIDE ?p.15CAL LEFT PUMP ?p.15PULL DISPENSEp.15CAL LF PUMP VOLp.15CAL LF WTR FLOW ?p.15PULL DISPENSERp.15CAL LF WTR VOL (-) 36.0OZ (+)p.15
Page 3 of the Bunn LCA-2 user manual — USER NOTICES
Page 3 · click to enlarge
Page 3

INTRODUCTION The Liquid Coffee Ambient Dispenser (LCA-2) and the Liquid Coffee Chilled Dispenser (LCC-2) delivers two types of coffee plus hot water. The dispenser can be set up for continuous draw (by the cup) for self-serve ap plications, or portion-control to fill carafes and decanters for wait staff. Product Flavor Profile is extended with chilled product storage cabinet featured in the LCC-2.

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protec tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

Bunn LCA-2 — USER NOTICES diagram (page 3)
Fig. 3
Bunn LCA-2 — USER NOTICES diagram (page 3)
Fig. 4

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). For models installed outside the U.S.A., comply with the applicable Plumbing /SanitationCode.

00656.0000

00986.0002

Bunn LCA-2 — USER NOTICES diagram (page 3)
Fig. 5
Bunn LCA-2 — USER NOTICES diagram (page 3)
Fig. 6

To reduce the risk of electric shock, do not remove or open cover. No user-serviceable parts inside. Authorized service personnel only. Disconnect power before servicing.

208-240 V, 25.8 A, 6200 W 1PH, 2-Wire + GND, 60HZ or 120/208-240 V, 25.8 A, 6200 W 1PH, 3-Wire + GND, 60HZ

37881.0000

28181.0003

11646.0002

· 34766 010407

Page 4 of the Bunn LCA-2 user manual — RED
Page 4 · click to enlarge
Page 4

ELECTRICAL REQUIREMENTS

Up.

The LCA-2 and LCC-2 dispensers are supplied with a 120-volt / 15 Amp cord set and require a 2-wire, grounded, individual branch circuit rated for 120 volts AC, 15 amp, single phase, 60Hz. The mating connector must be a NEMA 5-15R. The LCA-2C and LCC-2C dispensers are supplied with a 120-volt / 20 Amp cord set and require a 2-wire, grounded, individual branch circuit rated for 120 volts AC, 20 amp, single phase, 60Hz. The mating connector must be a NEMA 5-20R. These dispensers can be Field Wired for 208 or 240 volt applications. This requires a 2 or 3-wire, grounded, individual branch circuit rated for 208/240 volts AC, 30 amp, single phase, 60 Hz.

FIELD WIRING TERMINAL BLOCK DIAGRAM

Models without Master ON/OFF Switch

Bunn LCA-2 — FIELD WIRING TERMINAL BLOCK DIAGRAM diagram (page 4)
Fig. 7

LIMIT SW. - BLACK For all 208 - 240 Volt Connections: Use No. 10 AWG Wires suitable for 90°C (194 °F) 1. Unit shipped per Fig. 1, wired for 120V A.C./2-Wire. 2. For 208 - 240V A.C./2-Wire per Fig. 2: Move both the Red-Heater wire and the White-Fuse wire to the Top Red Terminal as shown. 3. For 120/208 - 240V A.C./3-Wire per Fig. 3: Move the Red Heater wire to the Top Red Terminal as shown.

FIELD WIRING TERMINAL BLOCK DIAGRAM

Models with Master ON/OFF Switch

RED ER F H208 240V BLACKFig.
RED ER F H120V A.C. 208 240V 120V A.C. BLACKFig. 3

RED

ON/OFF SWITCH

BLACK

For all 208 - 240 Volt Connections: Use No. 10 AWG Wires suitable for 90°C (194°F) 1. Unit shipped per Fig. 1, wired for 120V A.C./2-Wire. 2. For 208 - 240V A.C./2-Wire per Fig. 2. 3. For 120/208 - 240V A.C./3-Wire per Fig. 3.

· 34766 010407

Page 5 of the Bunn LCA-2 user manual — PLUMBING HOOK-UP
Page 5 · click to enlarge
Page 5

PLUMBING REQUIREMENTS

The dispenser may be connected to a cold or hot water system (140°F Max.) with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1/2” or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 3/8” flare. Dispensers set up to deliver to 1.8 Oz./sec. (53.2 ml/sec) per dispense tip, require a water supply source that can deliver a minimum of 1.7 gpm (6.4 lpm) at the inlet fitting. Dispensers set up to deliver 2.6 Oz./sec. (76.9 lpm) per dispense tip, require a water supply source that can deliver a minimum of 2.4 gpm (9.2 lpm) at the inlet fitting. NOTE: Bunn-O-Matic recommends 3/8” tubing from the 1/2” water supply line. At least 18 inches of FDA approved flexible beverage tubing, such as reinforced braided polyethylene or silicone, before the dispenser will facilitate movement to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). For models installed outside the U.S., you must comply with the applicable Plumbing/Sanitation Code for your area.

INITIAL SET-UP

1. Locate and remove the information packets and tube kits from top of packaging and set aside. 2. Remove foam packing and cut around the bottom of box. 3. Remove the box and the rest of the foam packing. 4. Open the dispenser door and remove the drip tray and the lower splash guard panel. 5. Set dispenser on the counter where it is to be used. CAUTION: DO NOT LIFT ON THE DOOR. 6. Confirm the dispenser is level on the counter.

ELECTRICAL HOOK-UP

1. An electrician must provide electrical service as specified in conformance with all local, state and federal electrical codes. 2. Using a voltmeter, check the voltage and color-coding of each conductor at the electrical source. 3. Connect the dispenser to the power source. 4. If plumbing is to be hooked up later, be sure the dispenser is disconnected from the power source. If plumbing has been hooked up, the dispenser is ready for Initial Fill & Heat.

PLUMBING HOOK-UP

1. Flush the water line to remove any debris or foreign material. 2. Securely attach the water line to the 3/8” flare fitting, on bottom right side of the dispenser. 3. Turn on the water supply and check for leaks.

· 34766 010407

Page 6 of the Bunn LCA-2 user manual — SETTING DISPENSER FLOW RATE
Page 6 · click to enlarge
Page 6

SETTING DISPENSER FLOW RATE

The dispenser comes from the factory with flow restrictors in the mix chambers. With the restrictors in place the dispense rate is about 1.8 oz./sec (53.2 ml/sec) and is used primarily for cup at a time dispensing. The flow restrictors can be removed to increase the dispense rate to about 2.5 oz./sec (74 ml/sec) for larger volume dispensing (airpots, carafes, etc.). NOTE: The hot water FlowRate is fixed at approximately 1.7 oz/sec. and can not be adjusted.

Removing the restrictors: 1. Disconnect the dispenser from the AC power source. 2. Open the Product Cabinet door. 3. Remove the concentrate tube, vent line and grommet from mix chamber ports in side the product cabinet. 4. Remove the two screws that fasten mix chamber to the control panel. 5. Gently pull mix chamber away from dispenser to expose water line connection, (you may have to rotate it slightly). 6. Disconnect FlavorGard™ sensor wire and hot water tubing from the mix chamber. 7. Remove the flow restrictor from the inlet to the mix chamber. 8. Reconnect FlavorGard™ sensor wire and hot water tubing to the mix chamber. 9. Place mix chamber back into position in the dispenser, (you may have to rotate it slightly) and secure it with the two screws 10. Reposition the grommet, vent line and pump tubing onto the mix chamber ports. Caution: Failure to properly replace and secure any of the above components may result leaks and/or cause damage to the dispenser.

If you changed the Dispenser Flow Rate, you will need to reprogram the dispenser to the new rate, see Programming the Dispenser. CAUTION: Failure to reprogram the Dispenser Flow Rates will result in inaccurate Mix Ratios.

Reprogramming the Dispenser Flow Rate: 1. Remove the lower splash guard panel and locate the Programming module. 2. Use the Down Arrow key to enter into the programming function and scroll through the menu’s to the “CAL LEFT SIDE?” menu and select “YES”. 3. Scroll down to the “CAL LF WTR VOL” menu 4. Use the (+) & (-) keys to enter a volume of 50 Oz. (1478 mL). This will recalibrate the Left dispenser to the new rate. 5. Scroll down to the “CAL RT WTR VOL” menu 6. Use the (+) & (-) keys to enter a volume of 50 Oz. (1478 mL). This will recalibrate the Right dispenser to the new rate. 7. Select “Exit” to leave the programming menu. Note: The default volume of 50 Oz (1478 mL), is the typical Cal Volume for a 2.5 Oz/sec Flow Rate Test, see Field Calibration of the Concentrate Pumps / Dispenser Flow Rates.

· 34766 120105

Page 7 of the Bunn LCA-2 user manual — SELECTING THE CORRECT PUMP TUBING
Page 7 · click to enlarge
Page 7

SELECTING THE CORRECT PUMP TUBING

There are two pump tube sizes available for use with this dispenser. To determine the correct tubing for you application, first determine the dispenser flow rate you intend to use, refer to Setting Dispenser Flow Rate. Then look up the recommended tube size for the mix ratio of your concentrate, refer to the Tube Selection Chart.

TUBE SELECTION CHART Dispense Concentrate Ratios Rate 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 1.8 Oz/sec. 3/16” I.D. TUBING 1/8” I.D. TUBING (53 ml/sec.) 2.5 Oz/sec. 3/16” I.D. TUBING 1/8” I.D. TUBING (74 ml/sec.)

Examples:

1. For a Dispenser Flow Rate of 2.5 Oz./sec (74 mL/sec) and a Mix Ratio of 35:1 – use 3/16” I.D. Tubing. 2. For a Dispenser Flow Rate of 1.8 Oz./sec (53 mL/sec) and a Mix Ratio of 60:1 – use 1/8” I.D. Tubing.

Tube kits can be purchased from BUNN-O-MATIC. Part # 34727.1000 for 3/16” I.D. Tubing or #34728.1000 for 1/8” I.D. Tubing.

INSTALLING THE PUMP TUBING (Refer to the Tubing Installation Instructions in side the cabinet door for details.) 1. Loosen the thumbscrew securing the tubing retainer plate to the pump housing. Set it and the retainer plate aside. 2. Depress the tension screw and remove it from the notch in the pump body, releasing the spring tension on the pump band. 3. Apply lubricant (BUNN-O-MATIC part number M2531.0001) to the new pump tubing. 4. Insert the tubing onto the mix chamber port and wrap the tubing around the pump rotor, making sure that the elbow and clamps end up on the bottom side of the pump body. 5. Close the compression band reinsert the tension screw into the notch in the pump housing. 6. Replace the tubing retainer plate and tighten the thumbscrew. 7. Reconnect bag connector to the product box. 8. Repeat steps 1 through 7 for the other pump. 9. Prime the pumps. Refer to Priming the Concentrate Lines section.

Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 8
Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 9
Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 10
Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 11

2.0” 2.0” Tension Screw

Remove Retaining Plate Release Spring Tension Remove Tubing Lubricate New Tube

Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 12
Bunn LCA-2 — SELECTING THE CORRECT PUMP TUBING diagram (page 7)
Fig. 13

Install New Tubing Completed Installation

Show 6 more labels / short text on this page
Thumbscrew · Lubricate between arrows · Tension Screw · Tube Clamp · · 34766 112502
Page 8 of the Bunn LCA-2 user manual — BUNN ICED COFFEE
Page 8 · click to enlarge
Page 8

OPERATING CONTROLS AND INTERFACE

1a. Dispense Handles: Pull and Hold to dispense product. 1b. Dispense Switches: Push and Release to dispense product for Portion Control Models. 2. Stop Switch: Momentary switch stops all dispense functions. 3a. Hot Water Switch: Push and Hold switch to dispense hot water from the center dispense tip. 3b. Push and Release switch for Portion Control Models. 4. Alternate Portion Control Switch: Momentarily pushed to select the Alternate Portion Control Volume #2. 5. Function Selector Switch: Allows the user to set the dispenser into different dispensing modes. a. Rinse: Dispenses hot water only- Flushes the mix chamber and dispense tip. b. Prime: Dispenses concentrates only – Primes the concentrate pump. c. Normal: Normal dispense mode - Dispenses mixed product (concentrate and water). 6. Mode Selector Switch: Allows the user to set the dispenser into different operating modes. a. Run: Normal operating position. b. Off: Turns off all functions including tank heater and chiller. WARNING - The OFF Mode does not remove AC power from the dispenser. Disconnect power source before servicing the dispenser

c. NightAnti-pilfering mode that disables dispensing, but keeps the tank heater and chiller (if applicable)

operational. 7. Door Interlock Switch: Unit will not dispense product if the door is open. 8. Power LED: Red - illuminates when AC power is applied to dispenser. 9. Ready LED: Green - illuminates when the water is at the preset ready temperature. 10. Portion LED: Yellow - illuminates when the portion dispense option has been selected, (5 second delay). 11. Rinse LED: Yellow - illuminates when the optional preset rinse alarm time has elapsed. 12. Left Refill LED: Yellow - illuminates when the Left Concentrate BIB needs replaced. 13. Right Refill LED: Yellow - illuminates when the Right Concentrate BIB needs replaced. 14. Programming Keypad: Used in conjunction with the LCD display to program and calibrate the dispenser to customer specific requirements. (Located behind the splash guard panel) 15. LCD Display: Displays programming menus and fault messages. (Located behind the splash guard panel)

Bunn LCA-2 — OPERATING CONTROLS AND INTERFACE diagram (page 8)
Fig. 14
Bunn LCA-2 — OPERATING CONTROLS AND INTERFACE diagram (page 8)
Fig. 15

BUNN ICED COFFEE

AMBIENT UNIT

12 15 14 · · 34766 120105

Page 9 of the Bunn LCA-2 user manual — INITIAL FILL & HEAT
Page 9 · click to enlarge
Page 9

INITIAL FILL & HEAT

1. Select Normal on the Function Selector Switch and Run on the Mode Selector Switch. 2. Confirm the water supply is on. 3. Connect the dispenser to the power source. The Red POWER LED will illuminate and water will begin flowing into the tank. The dispenser will automatically stop filling when the tank is full. The dispenser will not begin heating the water until after the tank is filled. Dispenser models with product chillers will begin to cool the cabinet at this time. 4. The Green READY LED will illuminate when the tank temperature reaches the preset ready temperature. Note: The time required to heat the water initially will vary depending on the AC Power supplied to the dispenser.

While the tank is heating, the dispenser may be readied for use as described in Programming Functions & Basic

Bunn LCA-2 — INITIAL FILL & HEAT diagram (page 9)
Fig. 16

· 34766 112502

Page 10 of the Bunn LCA-2 user manual — Rinse Alarm Feature
Page 10 · click to enlarge
Page 10

FlavorGard™ Feature

FlavorGard™ is a patented feed back control loop that monitors the mixed product and adjusts the concentrate delivery rate to maintain a consistent mix profile, i.e. Flavor Profile. The system consists of a conductance probe mounted in the final stages of the mixing chamber, a metering pump with RPM sensor and a digital controller. Once you have completed the installation of the dispenser, entered the desired mix ratio for your concentrate, dispensed several cups of the mixed product, and are satisfied with the Flavor and Strength being delivered, simply enable FlavorGard™, (refer to FlavorGard™ in Programming the Dispenser).

The dispenser will automatically calibrate the system to all the factors that make up your particular mix profile, (e.g. water source, filtration system, Brand of concentrate and mix ratio selected, etc.). NOTE: It is very important that you have dispensed enough product to insure that the dispenser is fully functional and you are satisfied with the Flavor Profile of the mix product before enabling FlavorGard™.

Once FlavorGard™ is enabled, the dispenser will continuously monitor the mix product as it is being dispensed and adjust the metering pump speed to maintain a consistent mixed product, thus eliminating factors such as (settling of the concentrate, tube wear, viscosity changes, liming, etc.).

The system is designed to work with in the range of variations that can be caused by these factors. The factory preset range is (+/- 10 %) and is adjustable to a Max of (+/- 15%). This insures that the FlavorGard™ system is not responding to factors that cannot be corrected by minor adjustments to the speed of the metering pump, (e.g. kinked hoses, low water pressure, severely worn tubes, empty BIB’s, etc). NOTE: Changes to Concentrate Ratios or Dispenser Flow Rates will automatically disable FlavorGard™. You will need to re-enable FlavorGard™, once you are satisfied with the new Flavor Profile.

Rinse Alarm Feature

Periodic rinsing of the mix chambers and dispense tips is essential for proper maintenance and optimum performance of the dispenser. The automated Rinse Alarm feature has three levels of operation, Disabled, Warning Only and Warning with Brew Lockout, see chart for details.

Alarm Level Selected Alarm Mode Disabled None Warning Only Rinse LED will come on 4 hrs prior to the selected time interval and remain on until the Rinse procedure has been performed. The dispenser will continue to serve product. Warning w/ Brew Lockout Rinse LED will come on 4 hrs prior to the selected time interval and remain on until the Rinse procedure has been performed. The dispenser will Lockout and not continue to serve product once the selected time interval has elapsed. NOTE: The time interval between Rinses is adjustable from 8 to 24 hrs.

The dispenser is shipped with the automated Rinse Alarm disabled, (No Alarm). It is up to the user to determine the Rinse time interval and the level of warning required, based on their application and maintenance procedures. To enable the automated Rinse Alarm feature, refer to RINSE ALARM ? in Programming the Dispenser.

34766 050103

Page 11 of the Bunn LCA-2 user manual — Brew Temperature Lockout Feature
Page 11 · click to enlarge
Page 11

Rinse Procedure:

1. Open the cabinet door and select Rinse on the Function Selector switch – close the door. 2. Place a 2 Liter (1/2 Gal) container under the Left dispense tip. 3. Activate the Left dispenser until water flow stops automatically, approximately 20 sec. 4. Repeat Steps 2 & 3 for the Right dispense tip. The Rinse LED will turn OFF, when the Rinse procedure has been satisfied for both sides. 5. Open the cabinet door and select Normal on the Function Selector switch – close the door.

BIB Empty Lockout Feature

The dispenser can be set to not dispense product when the concentrate BIB is empty. To enable this feature, first calibrate the Empty BIB Threshold (refer to Field Calibrating the Empty BIB Warning). Then enable the BIB Empty Lockout feature (refer to the BIB Empty Lockout menu in Programming the Dispenser). The dispenser will now Lockout dispensing and flash the Right or Left “REFILL LED” corresponding to the empty BIB. Once the BIB has been replaced, PRIME the concentrate line (refer to Priming the Concentrate Lines) and then dispense mixed product until the “REFILL LED” goes out. NOTE: If the dispenser fails to clear the BIB Empty Lockout, repeat the Priming operation a second time to insure the concentrate is flowing properly.

Brew Temperature Lockout Feature

The dispenser can be set to not dispense product if the hot water is not up to the preset READY temperature. To enable this feature set the READY temperature to the minimum allowable dispense temperature. Then enable the Brew Lockout feature, refer to READY TEMP and BREW LOCKOUT, in Programming the Dispenser.

34766 042304

Page 12 of the Bunn LCA-2 user manual — FIND RT TARGET PULL DISPENSE
Page 12 · click to enlarge
Page 12

PROGRAMMING THE DISPENSER

Remove the lower splash guard assembly to access the digital programming module with LCD display. Press the Down Arrow key to inter the programming menu. Use the Up and Down Arrow keys to scroll through the menu screens. Select Exit to leave the programming function and return to normal operations. NOTE 1: Flashing menu items indicate which selection is active. NOTE 2: Values shown below are the factory default values for English units. NOTE 3: Values in [X - X] are the Min. and Max. for that function.

MENU SCREEN ACTION DESCRIPTION

TANK TEMP XXX

Use the Down Arrow Key to enter Programming Functions

Normal Display for LCA models, (No Chiller)

AMBIENT UNIT

TANK TEMP XXX CABINET TEMP XX

Use the Down Arrow Key to enter Programming Functions

Normal Display for LCC models, (with Chiller)

L DISPENSE RATIO

Enter the desired Mix Ratio for the concentrate used in the Left dispenser. [20:1 - 100:1]

Use the (+) or (-) buttons to adjust the Mix Ratio

(-) 35:1 (+)

SET LF TUBE SIZE

Select tube size.

Enter Pump Tube Size to be used in the Left metering pump, (see Tube Selection Chart)

1/8 EXIT 3/16

R DISPENSE RATIO

Use the (+) or (-) buttons to adjust the Mix Ratio

Enter the desired Mix Ratio for the concentrate used in the Right dispenser. [20:1 - 100:1]

(-) 35:1 (+)

SET RT TUBE SIZE

Select tube size.

Enter Pump Tube Size to be used in the Right metering pump, (see Tube Selection Chart)

1/8 EXIT 3/16

FLAVOR GUARD ?

Select (YES) to activate. Select (NO) to deactivate.

Select Yes, if you are ready to calibrate the Flavor Guard sensor. Select NO, if you do not wish to use this feature, (see Flavor Guard)

NO EXIT YES

If NO - go to LF DISP VOLUME menu.

LF TASTE OK ? NO EXIT YES

Select (YES) or (NO)

Select YES, if you have dispensed several cups and are satisfied with the Left dispenser flavor. Select NO, if you have not run taste test.

FIND LF TARGET PULL DISPENSE

Place a 16 Oz. (500 mL) cup under the Left dispense tip, then activate the Left dispenser

Calibrates the Left FlavorGard™ sensor to the current MixProfile. The dispenser will shut OFF automatically when finished.

RT TASTE OK ? NO EXIT YES

Select (YES) or (NO)

Select YES, if you have dispensed several cups and are satisfied with the Right dispenser flavor. Select NO, if you have not run taste test.

FIND RT TARGET PULL DISPENSE

Place a 16 Oz. (500 mL) cup under the Right dispense tip, then activate the Right dispenser

Calibrates the Right FlavorGard™ sensor to the current MixProfile. The dispenser will shut OFF automatically when finished.

34766 042304

Page 13 of the Bunn LCA-2 user manual — WATER DISP VOL 2
Page 13 · click to enlarge
Page 13

MENU SCREEN ACTION DESCRIPTION

LOCK FLAVOR ?

Select (YES) or (EXIT)

Select YES, to Lock In sensor calibration. NOTE: Display will return to “Find LF Target” if sensor calibration is out of range.

EXIT YES

FLAVORS LOCKED

NONE

Confirms that sensor calibration was in range and accepted. Scroll down to continue.

EXIT

Portion Control Settings for Pull and Hold Dispensers For Portion Control Dispensers (LCA-2 PC, LCA-2C PC, LCA-2A PC) go to Full Time Portion Control Settings

LF DISP VOLUME

Use the (+) or (-) buttons to adjust the Left portion volume

Set the volume to be dispensed during a Left Portion controlled dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 4.0oz (+)

RT DISP VOLUME

Use the (+) or (-) buttons to adjust the Right portion volume

Set the volume to be dispensed during a Right Portion controlled dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 4.0oz (+)

Full Time Portion Control Settings

LF DISP VOLUME 1

Use the (+) or (-) buttons to adjust the Normal Left volume

Set the desired portion control volume to be dispensed during a Normal Left dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 4.0oz (+)

LF DISP VOLUME 2

Use the (+) or (-) buttons to adjust the Alternate Left volume

Set the desired portion control volume to be dispensed during a Alternate Left dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 0.0oz (+)

RT DISP VOLUME 1

Use the (+) or (-) buttons to adjust the Normal Right volume

Set the desired portion control volume to be dispensed during a Normal Right dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 4.0oz (+)

RT DISP VOLUME 2

Use the (+) or (-) buttons to adjust the Alternate Right volume

Set the desired portion control volume to be dispensed during a Alternate Right dispense to: [0 - 640 Oz.] or [0 - 18.93L]

(-) 0.0oz (+)

WATER DISP VOL 1

Use the (+) or (-) buttons to adjust the Normal Hot Water volume

Set the desired portion control volume to be dispensed during a Normal Hot Water dispense: [0 - 640 Oz.] or [0 - 18.93L]

(-) 0.0oz (+)

WATER DISP VOL 2

Use the (+) or (-) buttons to adjust the Alternate Hot Water volume

Set the desired portion control volume to be dispensed during a Alternate Hot Water dispense: [0 - 640 Oz.] or [0 - 18.93L]

(-) 0.0oz (+)

34766 120105

Page 14 of the Bunn LCA-2 user manual — NO EXIT YES
Page 14 · click to enlarge
Page 14

MENU SCREEN ACTION DESCRIPTION

TANK TEMP 180

Use the (+) or (-) buttons to adjust the target Temp.

Sets the water Tank temperature [120 - 200°F] or [49 - 93°C]

(-) EXIT (+)

READY TEMP 175

Use the (+) or (-) buttons to adjust the target Temp.

Sets the hot water Ready temperature. Typically set to the minimum desired dispense temp.

(-) EXIT (+)

CABINET TEMP 65

Use the (+) or (-) buttons to adjust the target Temp.

LCC Models OnlySets the Chilled Cabinet target temperature [50 - 75°F] or [4 - 24°C]

(-) EXIT (+)

LF PRODUCT DISP

Select (RESET) to clear total

Selecting Reset will clear the Current accumulated volume of concentrate dispensed through the Left dispenser. Gal (Liters)

.0GAL RESET?

LF PRODUCT DISP

NONE

Displays the Total accumulated volume of concentrate dispensed through the Left dispenser. Not Re-settable. Gal (Liters)

.0GAL

RT PRODUCT DISP

Select (RESET) to clear total

Selecting Reset will clear the Current accumulated volume of concentrate dispensed through the Right dispenser. Gal (Liters)

.0GAL RESET?

RT PRODUCT DISP

NONE

Displays the Total accumulated volume of concentrate dispensed through the Right dispenser. Not Re-Settable. Gal (Liters)

.0GAL

The following functions can be Password Protected. If you wish to prevent others from accessing these functions, enter a 4 digit code of your choice. Record your password code [ ], as you will need it to access these functions in the future.

ENTER PASSWORD

Use the (+) or (-) buttons to enter password.

Enter the access Code to view the remaining functions. Factory Default = 0.

SET PASSWORD ?

Use the (+) or (-) buttons to change the password.

Enter your own Code to prevent access to the remaining functions. [0 to 9999]

SELECT UNITS ENG EXIT METRIC

Select the preferred units

Used to select the preferred units of measurement. (Oz., Gal, deg F) or (mL, L, deg C)

CHILLED UNIT ? NO EXIT YES

Select (YES) or (NO)

LCA Models without Chiller select (NO) LCC Models with Chiller select (YES)

RINSE ALARM ?

Select (YES) or (NO)

Selecting Yes will enable the Rinse Alarm function, (see Rinse Alarm)

NO EXIT YES

If NO - go to BIB EMPTY LOCKOUT menu.

(-) 0 (+) · (-) 0 (+) · 34766 120105

Page 15 of the Bunn LCA-2 user manual — CAL RIGHT SIDE ?
Page 15 · click to enlarge
Page 15

MENU SCREEN ACTION DESCRIPTION

RINSE TIME ? (-) 12 Hrs (+)

Use the (+) or (-) buttons to adjust Rinse Alarm delay

Enter the desired time between required Rinse Cycles in hours, [8 - 24 hrs.]

RINSE LOCKOUT ?

Select (YES) to enable

Select YES to Lockout dispensing until the Rinse Alarm has been cleared. Default is NO

NO EXIT YES

Select (YES) to enable

Select YES to Lockout dispensing until the Concentrate BIB has been replaced. Default is NO

BIB EMPTY LOCKOUT

NO EXIT YES

BREW LOCKOUT ?

NO EXIT YES

Select (YES) to enable

Select YES to Lockout dispensing until the hot water tank is at READY Temp. Default is NO

DLY REPEAT DISP

(-) 0 SEC (+)

Use the (+) or (-) buttons to adjust the Delay Time

Enter the desired time delay before allowing the next dispense to take place, [0 - 10 sec.]

The following functions are for diagnostic and troubleshooting purposes and typically do not have to be adjusted. Contact your local service agent for assistance before making changes to these functions.

CAL LEFT SIDE ?

Select (YES) to enable

Selecting Yes will enable the Left Dispenser Calibration routine, (see Field Calibration before attempting to calibrate the dispenser).

EXIT YES

If NO - go to CAL RIGHT SIDE menu.

Place a 50 mL (#34843.1000) graduated cylinder under the Left dispense tip, then activate the Left Dispenser

The Left Pump will dispense concentrate for 20 seconds, then shut off automatically. Collect and measure the concentrate dispensed.

CAL LEFT PUMP ?

PULL DISPENSE

Use the (+) or (-) buttons to enter volume collected

Enter the volume of concentrate measured from the Left Pump in mL, (not Oz.) regardless of Preferred Units selected.

CAL LF PUMP VOL

Place a 64 Oz. (2000 mL) container under the Left dispense tip, then activate the Left Dispenser

The Left Dispenser will dispense hot water for 20 seconds, then shut off automatically. Collect and measure the water dispensed.

CAL LF WTR FLOW ?

PULL DISPENSER

Use the (+) or (-) buttons to enter volume collected

Enter the volume of the water measured from the Left dispenser in Oz. (mL).

CAL LF WTR VOL (-) 36.0OZ (+)

NONE

Scroll down to bypass this screen.

CAL LEFT SIDE ?

EXIT YES

Select (YES) to enable Calibration routine.

Selecting Yes will enable the Right Dispenser Calibration routine, (see Pump Calibration) prior to calibrating the dispenser.

CAL RIGHT SIDE ?

EXIT YES

(-) 43mL (+) · 34766 120105

Page 16 of the Bunn LCA-2 user manual — NONE
Page 16 · click to enlarge
Page 16

MENU SCREEN ACTION DESCRIPTION

If NO - skip to next menu.

CAL RIGHT PUMP ?

Place a 50 mL (#34843.1000) graduated cylinder under the Right dispense tip, then activate the Right Dispenser

The Right Pump will dispense concentrate for 20 seconds, then shut off automatically. Collect and measure the concentrate dispensed.

PULL DISPENSER

CAL RT PUMP VOL

Use the (+) or (-) buttons to enter volume collected

Enter the volume of concentrate measured from the Right Pump in mL(not Oz.) regardless of Preferred Units selected.

CAL RT WTR FLOW

Place a 64 Oz. (2000 mL) container under the Right dispense tip, then activate the Right Dispenser

The Right Dispenser will dispense hot water for 20 seconds, then shut off automatically. Collect and measure the water dispensed.

PULL DISPENSER

CAL RT WTR VOL (-) 36.0OZ (+)

Use the (+) or (-) buttons to enter volume collected

Enter the volume of the water measured from the Right dispenser in Oz. (mL)

CAL RIGHT SIDE ?

NONE

Scroll down to bypass this screen.

EXIT YES

For Portion Control Dispensers (LCA-2 PC, LCA-2C PC, LCA-2A PC) only

CAL HOT WTR FLO ?

Place a 64 Oz. (2000 mL) container under the Hot Water dispense tip, then activate the Hot Water Dispenser

The Hot Water Dispenser will dispense for 20 seconds, then shut off automatically. Collect and measure the water dispensed.

PULL DISPENSE

CAL HOT WTR VOL

Use the (+) or (-) buttons to enter volume collected

Enter the volume of the water measured from the Hot Water Dispenser in Oz. (mL)

(-) 34.0OZ (+)

XXX CAL -> XXX

Use the (+) or (-) buttons to adjust temperature reading

Adjust the display reading to match a calibrated probe inserted next to the Tank Sensor, °F (°C).

Use the (+) or (-) buttons to adjust % value

Used to set the maximum adjustment the Flavor Guard feature is allowed to make, [3 - 15%].

(-) EXIT (+)

LfFlvrGrdTargets RPM XXX-CON XXX

NONE

Displays the Left Dispenser target RPM and Conductance Reading, (Diagnostics Only)

RtFlvrGrdTargets RPM XXX-CON XXX

NONE

Displays the Right Dispenser target RPM and Conductance Reading, (Diagnostics Only)

Show 4 more labels / short text on this page
(-) 43mL (+) · (-) TankTemp (+) · FlvrGrdRange 10% · 34766 120105
Page 17 of the Bunn LCA-2 user manual — NO YES
Page 17 · click to enlarge
Page 17

MENU SCREEN ACTION DESCRIPTION

BIB EMPTY -> 500

Use the (+) or (-) buttons to adjust empty BIB threshold

Used to set the Conductance Threshold for the Empty BIB warning. Default is 500

(-) EXIT (+)

XX REFILL -> 155

Use the (+) or (-) buttons to adjust Refill threshold

Used to set the Conductance Threshold for the Tank Refill Probe.

(-) EXIT (+)

WTR START DELAY

Use the (+) or (-) buttons to adjust delay time

Dispense Valve ON Delay. Eliminates weak mix at the beginning of a dispense.

(-) .15SEC (+)

WTR STOP DELAY

Use the (+) or (-) buttons to adjust delay time

Dispense Valve OFF Delay. Flushes the mix chamber at the end of a dispense.

(-) .15SEC (+)

TEST LED’S ? NO EXIT YES

Select (YES) or (NO)

LED diagnostics. Selecting YES will light all Front Door LED’s.

TEST SWITCHES ?

NONE

Switch Diagnostic: Activate switches separately to test. Display will indicate which Switch has been activated. NOTE: Door Interlock switch must be held closed.

TEST REFILL ? EXIT YES

Refill Valve Diagnostic: Press YES to momentarily energize the Solenoid. CAUTION: Inlet Valve will open and water will flow, if connected and turned ON.

TEST HEATER ?

Tank Heater Diagnostic: Press YES to momentarily energize the Tank Heater Circuit. CAUTION: AC power will be applied to the Tank Heater Circuit.

EXIT YES

ENTER ASSET #

Use the (+) or (-) buttons to adjust the ASSET NUMBER

Allows the user the option of entering an Asset Number. Default is 000000

SERIAL # LCA 0000000

NONE

Displays the manufacture’s Serial Number (should be identical to the Serial Number on the machine Data Plate)

FACTORY DEFAULTS

Select (YES) or (NO)

NO YES

Show 5 more labels / short text on this page
UseSwitchToTest · Momentarily depress (YES) · Momentarily depress (YES) · (-) 000000 (+) · 34766 061605
Page 18 of the Bunn LCA-2 user manual — RINSE LOCKOUT ?
Page 18 · click to enlarge
Page 18

LOADING THE CONCENTRATE 1. Thoroughly mix concentrate by vigorously shaking the product Bag-In-Box (BIB). 2. Pull the BIB connector through the hole provided in the box and place it on the drip tray with the connector facing up. (See Fig. 1) 3. Open the dispenser door and locate the appropriate left or right BIB Adapter fitting. 4. Pull the Adapter fitting down and connect it to the BIB. (See Fig. 2) 5. Place the BIB upright in the machine, rotating it into position with the connector facing forward. 6. Rotate the BIB Adapter to avoid sharp bends in the tubing and allow it to be routed between the two pumps. Refer to the Tube Installation Decal on the door for proper routing. (See Fig. 3) 7. Close the cabinet door.

Bunn LCA-2 — RINSE LOCKOUT ? diagram (page 18)
Fig. 17
Bunn LCA-2 — RINSE LOCKOUT ? diagram (page 18)
Fig. 18
Bunn LCA-2 — RINSE LOCKOUT ? diagram (page 18)
Fig. 19

Fig. 1 Fig. 2 Fig. 3

PRIMING THE CONCENTRATE LINES 1. Open the dispenser door. 2. Load concentrate per instructions in the section titled Loading the Concentrate. 3. Select Prime on the Function Selector Switch and Run on the Mode Selector Switch. 4. Close the dispenser door. 5. Place a container under the appropriate dispense tip. 6. Activate the appropriate dispenser until concentrate flows from the dispense nozzle. Priming may take 5 to 10 seconds. 7. Open the dispenser door, select Normal on the Function Selector Switch, and then close door. Note: Concentrate may continue to drip out of dispense tip. The user may wish to run a Rinse Cycle (refer to Rinsing) after Priming the dispenser to clean out the remaining concentrate.

Bunn LCA-2 — RINSE LOCKOUT ? diagram (page 18)
Fig. 20

34766 042304

Page 19 of the Bunn LCA-2 user manual — RINSE LOCKOUT ?
Page 19 · click to enlarge
Page 19

OPERATING THE PULL & HOLD DISPENSER (Models LCA-2, LCA-2C, LCA-2A, LCC-2, LCC-2C, LCC-2A) Set the Function Selector Switch to Normal and the Mode Selector Switch to Run. 1. Pull and Hold Dispense Mode (Cup at a time) a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up

and place the container on top of the drip tray. b. Pull and Hold the corresponding dispense handle until the cup or other container is full. c. Remove cup or container. 2. Portion Dispense Mode (Preset volume dispensing) Refer to Programming Functions on how to set this volume. a. Place the appropriate size container beneath the desired dispensing tip. For large containers, flip the cup

tray up and place the container on top of the drip tray. b. Momentarily press the Portion Switch. The Portion LED will illuminate for 5 seconds after the Portion

Switch is pressed. c. Momentarily pull the corresponding dispense handle, then release. If the user waits longer than 5 seconds

to pull the handle, the dispenser will default back to the Pull & Hold Mode. Portion Dispense Mode can be disabled at any time during the portion dispense by either momentarily pulling the Dispense Handle again or pressing the Stop button. d. Wait for container to fill and the dispenser to quit dispensing, then remove container. 3. Hot Water Dispense a. Place container under the hot water dispenser (center of machine). For large containers, flip the cup tray

up and place the container on top of the drip tray. b. Push and hold the Hot Water Switch until the water reaches the desired level, then release. c. Remove container.

Filling Cambros or other large containers: The dispenser is designed primarily for cups or other small containers that will fit under the dispense tips. However, it may be used to fill larger containers (up to 2 Gal) by use of an extension hose on the dispense tip. Removing the Flow Restrictors will increase the dispenser flow rate to 2.5 Oz/sec. (74 mL/sec.) and reduce the time to fill larger containers, (see Setting Dispenser Flow Rate.) Care must be taken to insure that the mixed product flows freely from the dispense tip into the container. 1. Use a 5/8” I.D. or larger, NSF (National Sanitation Foundation) approved hose. 2. Use as short a hose as possible with no loops, bends or kinks in it. 3. Insure that the outlet of the hose is below the dispense tip and that the mixed product flows freely into the container A properly sized and positioned hose will not run full or back up into the dispense tip. Failure to follow these directions can alter the mix ratio and/or cause flooding of the vent tube. NOTE: The temperature of the product being dispensed will start to drop after ~2 gal. continuous draw. Recovery time will be dependent on the temperature of the supply water and the voltage at which the heater coil is being operated.

34766 042304

Page 20 of the Bunn LCA-2 user manual — OPERATING THE PRESET PORTION CONTROL DISPENSER
Page 20 · click to enlarge
Page 20

OPERATING THE PRESET PORTION CONTROL DISPENSER

(Models LCA-2 PC, LCA-2C PC, LCA-2A PC) Set the Function Selector Switch to Normal and the Mode Selector Switch to Run.

Dispensing Preset Portions of Coffee or Hot Water 1. Primary Volume Portion Dispense Mode. (Volume 1) Refer to Programming Functions on how to set this amount. a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up

and place the container on top of the drip tray. b. Momentarily press the appropriate dispense switch. The dispenser will automatically dispense the beverage

at the preset amount. Allow the mix chamber to drain at the end of the cycle. c. Remove cup or container. 2. Alternate Volume Portion Dispense Mode. (Volume 2) Refer to Programming Functions on how to set this volume. a. Place the appropriate size container beneath the desired dispensing tip. For large containers, flip the cup

tray up and place the container on top of the drip tray. b. Momentarily press the Portion Switch. The Portion LED will illuminate for 5 seconds after the Portion

Switch is pressed. c. Momentarily press the corresponding Dispense Switch. If the user waits longer than 5 seconds to push

the switch, the dispenser will default back to the Primary Volume preset amount. Alternate Portion Dispense Mode can be disabled at any time during the portion dispense by either momentarily pushing the Dispense Switch again or pressing the Stop button. d. Wait for the container to fill and the dispenser to quit dispensing, then remove the container.

Push and Hold Dispensing of Coffee or Hot Water Push and Hold Dispense Mode. See Programming Functions on how to set the Preset Volume to Zero.

a. Place cup on the cup tray beneath the desired dispensing tip. For a large container, flip the cup tray up

and place the container on top of the drip tray. b. Push and hold the corresponding dispense switch until the container is full. c. Remove cup or container.

Filling Cambros or other large containers: The dispenser is designed primarily for cups or other small containers that will fit under the dispense tips. However, it may be used to fill larger containers (up to 5 Gal) by use of an extension hose on the dispense tip. Removing the Flow Restrictors will increase the dispenser flow rate to 2.5 Oz/sec. (74 mL/sec.) and reduce the time to fill larger containers, (see Setting Dispenser Flow Rate.) Care must be taken to insure that the mixed product flows freely from the dispense tip into the container. 1. Use a 5/8” I.D. or larger, NSF (National Sanitation Foundation) approved hose. 2. Use as short a hose as possible with no loops, bends or kinks in it. 3. Insure that the outlet of the hose is below the dispense tip and that the mixed product flows freely into the container A properly sized and positioned hose will not run full or back up into the dispense tip. Failure to follow these directions can alter the mix ratio and/or cause flooding of the vent tube. NOTE: The temperature of the product being dispensed will start to drop after ~2 gal. continuous draw. Recovery time will be dependent on the temperature of the supply water and the voltage at which the heater coil is being operated.

34766 120105

Page 21 of the Bunn LCA-2 user manual — CLEANING & PREVENTATIVE MAINTENANCE
Page 21 · click to enlarge
Page 21

CLEANING & PREVENTATIVE MAINTENANCE

General Cleaning and Sanitizing Procedures Note: The BUNN® Liquid Coffee Dispenser incorporates a “user selectable” rinse reminder feature, which lights the Rinse LED on the front panel and disables dispensing when it is time to rinse. See Programming Functions to activate this feature.

Daily: RINSING 1. Open the dispenser door. 2. Select Rinse on the Function Selector Switch and Run on the Mode Selector Switch. 3. Close the dispenser door. 4. Place a 1/2 gal (2 liter) container under the appropriate dispense nozzle or nozzles. 5. Activate the Dispenser of the appropriate side or sides for approximately twenty seconds or until the hot water is clear or has no concentrate coloring in it. 6. Open the dispenser door, select Normal on the Function Selector Switch, and then close door. Note: To clear the “Rinse” alarm, activate each dispenser until the flow stops automatically (approx. 20 seconds for each tip). The “Rinse” alarm LED will turn off when the Rinse Procedure has been satisfied for both sides.

Daily: PARTS WASHING 1. Remove and wash the drip tray, drip tray cover, and cup tray in a mild detergent solution. Rinse thoroughly. 2. Wipe splash panel, area around dispense nozzles, door, and cabinet with a clean damp cloth.

Weekly: SANITIZING 1. Open the dispenser door. 2. Select Prime on the Function Selector Switch and Run on the Mode Selector Switch. 3. Remove the bag connector from the product box and disassemble or prop open the internal valve to allow free flow of product through the connector. NOTE: Cutting the mating fittings from an empty bag makes an excellent “free flowing” connector for this purpose. 4. Place the bag connector into a one-gallon (3.8 liter) container of warm soapy tap water 140°F (60°C). 5. Place an empty container under dispense tip and activate the corresponding Dispenser until the clean soapy water is dispensed from the dispense tip. 6. Repeat steps 4 and 5 with warm tap water 140°F (60°C) to rinse the soapy water from the pump tubing. Continue dispensing until the water is clear, and no soapy water is being dispensed. 7. Prepare 2.5 gallons (9.46L) of sanitizing solution by dissolving 1 packet of Kay 5 sanitizer into 2.5 gallons (9.46L) of 120°F (48.9°C) water to ensure 100 ppm of available chlorine. 8. Again, repeat steps 4 and 5 with the sanitizing solution. Once sanitizing solution is being dispensed, stop dispensing and allow the solution to sit for 5 minutes. 9. Repeat step 6 to flush out the sanitizing solution from the pump tubing. 10. Remove the mating connector from the bag connector. 11. Reattach the bag connector to product box. 12. Select Normal on the Function Selector Switch and Run on the Mode Selector Switch. 13. Activate the Dispenser until concentrate/water mixture appears. Then dispense one 12 ounce (354.9 ml) glass of concentrate/water mixture and discard. 14. Repeat steps 1 through 13 for other dispense head. 15. Wipe internal and external surfaces with a clean, damp cloth.

34766 042304

Page 22 of the Bunn LCA-2 user manual — REPLACING THE PUMP TUBING
Page 22 · click to enlarge
Page 22

REPLACING THE PUMP TUBING

The pumps and tubing used in the dispenser are designed to give maximum performance and long life. However, the tubes are a wear item and must be replaced periodically. How long the tubes last is dependent on usage and properties of the concentrate. Excessive wear will reduce the output of the pumps resulting in a weak mixed beverage. Bunn-O-Matic recommends replacing the Pump Tubing a minimum of once every 6 months or sooner if warranted. Refer to the Tube Replacement Instruction on the Cabinet door for details. 1. Rinse the pump tubing with warm tap water (Refer to steps 1 - 5 of the Weekly Sanitizing instructions) prior to removing the tubes to avoid concentrate spills. 2. Loosen the thumbscrew securing the tubing retainer plate to the pump housing. Set it and the retainer plate aside. 3. Depress the tension screw and remove it from the notch in the pump housing, releasing the spring tension on the pump band. 4. Open the compression band and gently pull the pump tube from around the pump’s rotor. 5. Inspect the pump bands for signs of wear. Replace if necessary. 6. Apply lubricant (BUNN-O-MATIC part number M2531.0001) to the new pump tubing’s rotor side. 7. Insert the tube onto the mix chamber port, then wrap the new tubing around the pump rotor, making sure that the elbow and clamps end up on the bottom side of the pump housing. 8. Depress the tension screw and insert it in the notch in the pump body, reapplying spring tension on the pump band. 9. Replace the tubing retainer plate and tighten the thumbscrew. 10. Repeat steps 1 through 9 for the other pump.

2.0” 2.0” Tension Screw

Remove Retaining Plate Release Spring Tension Remove Tubing Lubricate New Tube

Install New Tubing Completed Installation

Show 5 more labels / short text on this page
Thumbscrew · Lubricate between arrows · Tension Screw · Tube Clamp · 34766 112502
Page 23 of the Bunn LCA-2 user manual — DRAINING THE HOT WATER TANK
Page 23 · click to enlarge
Page 23

DRAINING THE HOT WATER TANK

CAUTION: The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source. 2. Shut off and disconnect the incoming water supply. 3. Remove the front splash panel. 4. Pull out drain tube to empty into a sink or a container with a minimum of five-gallon capacity. 5. Make sure drain clamp is closed. Then, remove drain plug. 6. Direct tube into sink or container and open drain clamp. Continue draining tank until ALL of the water is out. Be very careful with the draining water because it can be very hot. 7. Close drain clamp, insert drain plug, place drain tube back into machine, and replace splash panel. Note: The dispenser must be refilled using the Initial Fill & Heat steps before reconnecting the power source.

34766 112502

Page 24 of the Bunn LCA-2 user manual — Front Panel LED Display Messages
Page 24 · click to enlarge
Page 24

Troubleshooting

  • A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.
  • Only qualified service personnel should perform inspection, testing, and repair of electrical equipment.
  • Shorting the terminals or the application of external voltages to electronic components may result in component or circuit board failure.
  • Intermittent operation of electronic circuit boards is unlikely. board failure will normally be permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or a loose wire connection at a terminal or crimp.
  • Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water.
  • The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help avoid twists and kinks in the tubing.
  • Make certain that all plumbing connections are sealed and all electrical connections are tight and isolated.
  • This dispenser is heated at all times. Keep away from combustibles. WARNING:
  • Exercise extreme caution when servicing electrical equipment.
  • Disconnect the brewer from the power source when servicing, except when electrical tests are specified. The red “Power LED” on the door indicates that the unit is connected to AC Power.
  • Follow recommended service procedures.
  • Replace all protective shields or safety notices.

Front Panel LED Display Messages

Dispenser Not plugged in. AC Circuit Breaker OFF Power LED “OFF”

Check Power Cord Check the AC Power Circuit Breaker Service Required

Usage has exceeded the capacity of the Tank Heater Ready LED “OFF” Water Temp. Too Low

Check Tank Temp Setting Check Ready Temp. Setting Service Required: Change the Supply Voltage, see Optional Field Wiring

Rinse Dispenser, see Rinse Procedure Rinse Cycle Required Rinse LED “ON”

Rinse Dispenser, see Rinse Procedure Dispenser Locked Out Rinse Cycle Required Rinse LED “FLASHING”

Alternate Portion Dispenser Volume #2 has been selected Portion LED “ON”

Activate the Dispenser within 5 sec. to dispense the pre-selected volume.

Show 6 more labels / short text on this page
No AC Power · Rinse Timer · Rinse Lockout Enabled · Portion Dispense · Enabled · 34766 042304
Page 25 of the Bunn LCA-2 user manual — Troubleshooting (Continued)
Page 25 · click to enlarge
Page 25

Troubleshooting (Continued)

Left Refill LED “ON”

Concentrate BIB is Empty. BIB Not properly connected Tubing kinked or blocked Empty BIB warning set too high

Replace BIB, see Loading the Concentrate Check BIB Connector Fittings Check Tubing Installation Check Threshold, see Field Calibrating the Emoty BIB Warning

Right Refill LED “ON”

Concentrate BIB is Empty. BIB Not properly connected Tubing kinked or blocked Empty BIB Warning set too high

Replace BIB, see Loading the Concentrate Check BIB Connector Fittings Check Tubing Installation Check Threshold, see Field Calibrating the Empty BIB Warning

Replace BIB, see loading the Concentrate Left Dispenser will not operate Left Refill LED

“FLASHING” Empty BIB Lockout

Left Dispenser will not operate

Replace BIB, see loading the Concentrate

“FLASHING” Empty BIB Lockout

The Dispenser has detected an Internal Fault

Remove the lower splash guard to view the Fault message, See Diagnostics. After the fault has been repaired or corrected - Hold the “Stop” button for 10 seconds to clear the message.

Show 8 more labels / short text on this page
Left BIB Empty · Right BIB Empty · Enabled · Left Refill LED · Enabled · All LED’s “FLASHING” · Fault Detected · 34766 102103
Page 26 of the Bunn LCA-2 user manual — CHECK THRESHOLD
Page 26 · click to enlarge
Page 26

Troubleshooting (Continued)

Screen Displayed Possible Cause Troubleshooting Procedures Dispenser Diagnostics-LCD Display

LF TARGET RPM TOO HIGH !!

1. The Tube Size selected for the Left Hand Dispenser is too small for the application.

Refer to “Selecting the Correct Pump Tubing” section of the manual.

TUBE TOO SMALL CHECK DISP RATIO

2. The Ratio selected for the Left Hand Dispenser is not correct for the application.

Refer to recommended Dispense Ratio on the product label.

RT TARGET RPM TOO HIGH !!

1. The Tube Size selected for the Right Hand Dispenser is too small for the application.

Refer to “Selecting the Correct Pump Tubing” section of the manual.

TUBE TOO SMALL CHECK DISP RATIO

2. The Ratio selected for the Right Hand Dispenser is not correct for the application.

Refer to recommended Dispense Ratio on the product label.

LF TARGET RPM TOO LOW !!

1. The Tube Size selected for the Left Hand Dispenser is too large for the application.

Refer to “Selecting the Correct Pump Tubing” section of the manual.

TUBE TOO LARGE CHECK DISP RATIO

2. The Ratio selected for the Left Hand Dispenser is not correct for the application.

Refer to recommended Dispense Ratio on the product label.

RT TARGET RPM TOO LOW !!

1. The Tube Size selected for the Right Hand Dispenser is too large for the application.

Refer to “Selecting the Correct Pump Tubing” section of the manual.

TUBE TOO LARGE CHECK DISP RATIO

2. The Ratio selected for the Right Hand Dispenser is not correct for the application.

Refer to recommended Dispense Ratio on the product label.

LEFT BIB EMPTY!

1. Concentrate BIB is Empty.

Replace BIB, see loading the Concentrate

2. BIB Not properly connected.

Check BIB Connector Fittings

REPLACE PRODUCT

3. Tubing kinked or blocked.

CHECK THRESHOLD

4. Empty BIB Warning set too high.

Check Threshold, see Field Calibrating the Empty BIB Warning

RIGHT BIB EMPTY!

1. Concentrate BIB is Empty.

Replace BIB, see loading the Concentrate

2. BIB Not properly connected.

Check BIB Connector Fittings

REPLACE PRODUCT

3. Tubing kinked or blocked.

CHECK THRESHOLD

4. Empty BIB Warning set too high.

Check Threshold, see Field Calibrating the Empty BIB Warning

Check Tubing installation · Check Tubing installation · 34766 011604

Page 27 of the Bunn LCA-2 user manual — CHECK WIRE FOR SHORTS
Page 27 · click to enlarge
Page 27

Troubleshooting (Continued)

Screen Displayed Possible Cause Troubleshooting Procedures

OVERFLOW CUP FULL. EMPTY CUP

1. Refill valve stuck open
2. Faulty refill probe
3. Faulty overflow switch

HEATING TIME TOO LONG CHECK HEATING CIRCUIT

1. Tank Heater failure
2. Triac failure
3. Tank Temp. sensor failure 1. Water shut off to dispenser

FILL TIME TOO LONG

Check water supply shut-off

CHECK WATER SUPPLY

2. Inlet Solenoid Valve failure

TANK TEMP SENSOR OUT OF RANGE CHECK FOR BAD CONNECTIONS

1. Corresponding Temperature Sensor Probe wire(s) broken or disconnected

COOL TEMP SENSOR OUT OF RANGE

1. Corresponding Temperature Sensor Probe wire(s) broken or disconnected.

CHECK FOR BAD CONNECTIONS

2. Product cabinet temperature too low.

EVAP TEMP SENSOR OUT OF RANGE

1. Corresponding Temperature Sensor Probe wire(s) broken or disconnected.

CHECK FOR BAD CONNECTIONS

2. Evaporator temperature too low.

TANK TEMP SENSOR OUT OF RANGE CHECK WIRE FOR SHORTS

1. Corresponding Temperature Sensor Probe wire(s) shorted to housing, or to each other.

COOL TEMP SENSOR OUT OF RANGE

1. Corresponding Temperature Sensor Probe wire(s) shorted to housing, or to each other.

CHECK WIRE FOR SHORTS

2. Product cabinet temperature too high.
Show 16 more labels / short text on this page
Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · 34766 011604
Page 28 of the Bunn LCA-2 user manual — CHECK J-18 ON CONTROL BOARD
Page 28 · click to enlarge
Page 28

Troubleshooting (Continued)

Screen Displayed Possible Cause Troubleshooting Procedures

EVAP TEMP SENSOR OUT OF RANGE

1. Corresponding Temperature Sensor Probe wire(s) shorted to housing, or to each other.

CHECK WIRE FOR SHORTS

2. Evaporator temperature too high.

LEFT PUMP FAULT! CHK PUMP WIRING CHK RPM SENSOR CHK TUBING AREA

1. Motor failure
2. RPM Sensor failure

RT PUMP FAULT! CHK PUMP WIRING

1. Motor failure
2. RPM Sensor failure

CHK RPM SENSOR CHK TUBING AREA

COOLER FAULT! EVAP TEMP TOO HI

1. Cabinet circulating fan failure
2. Ice build up on evaporator coils

CHECK EVAP FAN CHK EVAP SENSOR

3. Evaporator sensor failure

COOLING TIME TOO LONG

1. Air intake filter clogged
2. Wiring failure

Check wiring harness for breaks, shorts, open connectors

CHECK AIR FILTER CHECK COOLING UNIT

3. Compressor failure

COND PROBE FAULT CHECK COND PROBES

1. Tube leaking

Check pump & tubing for proper installation Service Required

2. Dispense switch failure

CHK DISP SWITCHES CHK CONNECTIONS

3. Dispense valve leaking

JUMPER FAULT! CONFIG NOT VALID

1. Invalid wire harness configuation

CHECK J-18 ON CONTROL BOARD

Show 14 more labels / short text on this page
Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Service Required · Clean Air Filter · Service Required · Service Required · Service Required · 34766 010407
Page 29 of the Bunn LCA-2 user manual — Field Calibration of the Concentrate Pumps / Dispenser Flow Rates
Page 29 · click to enlarge
Page 29

Field Calibration of the Concentrate Pumps / Dispenser Flow Rates

The factory set Default Values for the Pump & Dispenser Flow Rates are very accurate and typically do not need to be field calibrated. However, if the mix ratio accuracy is ever in question, this procedure can be used to recalibrate the unit in the field. Equipment Required: 50 to 100 ml graduated cylinder, with 1 ml graduations. 64 Oz (2000 ml) graduated container. Remove the lower splash guard assembly to access prior to starting this procedure NOTE: You can calibrate either the Concentrate Pump or the Dispenser Flow Rate independently. Simply scroll through the menu screen to the desired section and perform only those steps.

Calibrating the Left Side Dispenser

Concentrate Pump Calibration 1. Select PRIME on the Function Selector Switch. (refer to Priming the Concentrate Lines). 2. Place a container under the Left Dispense Tip and prime the concentrate lines until a steady stream of concentrate comes out the tip (approximately 10 seconds). 3. Stop the Priming and allow the tip to stop dripping. Discard the concentrate collected. 4. Select NORMAL on the Function Selector Switch. 5. Locate the programming module and use the Arrow Down key to scroll through LCD screens until CAL LEFT SIDE appears and press the YES button. 6. The CAL LEFT PUMP menu screen will be displayed. Place a 50 ml graduated cylinder under Left Dispense Tip and activate the Left Dispenser momentarily. The dispenser will run the Left Concentrate Pump for 20 seconds and then shut OFF automatically. 7. Keep the graduated cylinder under dispense tip until all the concentrate has dripped out. 8. Measure the volume of concentrate collected in the graduated cylinder.

Acceptable ranges for the volume collected Tubing Size Volume Collected 3/16” tubing 40 - 47 ml. 1/8” tubing 17 - 22 ml

9. If the amount collected is not within the acceptable range, empty the graduated cylinder and repeat STEPS 6 – 8. 10. If the amount collected is still not within range, replace the pump tubing with a new Tube Kit, (refer to the Tube Replacement Instructions). 11. When satisfied with the volume of concentrate collected, press the Down Arrow Key 12. The CAL LF PUMP VOL menu screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the amount measured in STEP 8.

(Continued Next Page) · 34766 042304

Page 30 of the Bunn LCA-2 user manual — Field Calibration of the Concentrate Pumps / Dispenser Flow Rates
Page 30 · click to enlarge
Page 30

Field Calibration of the Concentrate Pumps / Dispenser Flow Rates

(Continued)

Dispenser Flow Rate Calibration 13. Press Down Arrow Key to display the CAL LF WTR FLO menu screen. 14. Place a 64 Oz (2000 ml) graduated container under Left Dispense Tip and Pull the Left Dispense Handle momentarily. The dispenser will dispense water for 20 seconds and then shut OFF automatically. 15. Keep the graduated container under dispense tip until all the water stops dripping. 16. Measure the volume of water collected in the graduated container.

Acceptable ranges for the volume collected Dispenser Flow Rate Volume Collected 1.8 Oz/sec (53 ml/sec) w/ flow restrictor 32 - 38 Oz, (946 - 1124 ml) 2.5 Oz/sec (74 ml/sec) w/o flow restrictor 46 - 52 Oz ,(1360 - 1538 ml)

17. If the amount collected is not within the acceptable range, empty the graduated container and repeat STEPS 14 – 16 18. If the amount collected is still not within range, inspect the dispense valves, tubing and mix chamber for lime, kinks or other obstructions. 19. When satisfied with the volume of concentrate collected, press the Down Arrow Key. 20. The CAL LF WTR VOL screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the amount measured in STEP 16. 21. Press Down Arrow Key again to exit the CAL LEFT SIDE functions.

Calibrating the Right Side Dispenser

Repeat STEPS 1-21 above for the “CAL RIGHT SIDE” menus.

Field Calibrating the Hot Water Flow Rate 1. Locate the programming module and use the Arrow Down key to scroll through the LCD screen until “CAL HOT WTR FLO?” appears. 2. Place a 64 Oz (2000 ml) graduated container under Hot Water Tip and press the hot water switch. The unit will dispense Hot Water for 20 seconds and then shut OFF automatically. Keep the graduated container under the dispense tip until all the water stops dripping. 3. Measure the volume of water collected in the graduated container. The acceptable range for the volume collected is 32 - 38 Oz. (946 - 1124 ml). 4. If the amount collected is not within the acceptable range, empty the container and repeat steps 2 & 3. 5. If the amount collected is still not within range, inspect the hot water valve, tubing and fittings for lime, kinks, or other obstructions. 6. When satisfied with the volume of concentrate collected, press the Down Arrow Key. 7. The “CAL HOT WTR VOL” screen will be displayed. Use the (-) / (+) keys to adjust number displayed to the ammount measured in step 3. 8. Press Down Arrow Key again to exit this function.

30 34766 120105

Page 31 of the Bunn LCA-2 user manual — RINSE LOCKOUT ?
Page 31 · click to enlarge
Page 31

Field Calibrating the Empty BIB Warning The dispenser will automatically turn on the Left or Right “REFILL LED”, see Operating Controls and Interface, when the corresponding BIB is Empty. The Refill message is triggered when the FlavorGardTM sensor reading drops below the minimum setting. The factory set minimum is 500 and should be correct for most locations. However, in some areas the hardness of the local water supply may effect this reading. If the Refill message doesn’t come on when the BIB is empty or the message comes on too early and there is still concentrate left in the BIB, use the following procedure to find the correct Empty BIB threshold.

Calibrating The Empty BIB Threshold 1. Remove the lower splash guard assembly to access the digital programming module with LCD display. 2. Open the cabinet door and set the Function Switch to the “Rinse” position. Close the door. 3. Place a large container under the Left dispenser tip, then activate and hold the left dispenser. 4. Dispense long enough to rinse all the concentrate out of the mix chamber and for the Conductance reading to stabilize and stop dropping. 5. Record the nominal Conductance value displayed. (NOTE: It is typical for this value fluctuate (+/- 25) points about the nominal value}. This is the conductance reading of the water in your area. 6. Repeat steps 3, 4 & 5 for the Right dispenser. 7. Add 100 points to the larger of the Left or Right side Conductance value. This is the new Empty BIB threshold value for your dispenser. 8. Enter this new value into the Empty BIB Alarm threshold, see Programming the Dispenser.

34766 120105

Page 32 of the Bunn LCA-2 user manual — Models without Master ON/OFF Switch
Page 32 · click to enlarge
Page 32

SCHEMATIC WIRING DIAGRAM LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C

N (120V 2-Wire) N (120/208-240V 3-Wire) L2 (208-240V 2-Wire)

Bunn LCA-2 — SCHEMATIC WIRING DIAGRAM LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C diagram (page 32)
Fig. 21

120 VOLTS AC 2 WIRE 120/208-240 VOLTS AC 3 WIRE 208-240 VOLTS AC 2 WIRE SINGLE PHASE 50/60HZ

Models without Master ON/OFF Switch

32 34766 010407

Page 33 of the Bunn LCA-2 user manual — SCHEMATIC WIRING DIAGRAM LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C
Page 33 · click to enlarge
Page 33

SCHEMATIC WIRING DIAGRAM LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C

Bunn LCA-2 — SCHEMATIC WIRING DIAGRAM LCA-2/LCA-2, PC/LCA-2C/LCA-2C, PC/LCC-2/LCC-2C diagram (page 33)
Fig. 22

120 VOLTS AC 2 WIRE 120/208-240 VOLTS AC 3 WIRE 208-240 VOLTS AC 2 WIRE SINGLE PHASE 50/60HZ

34766 010407

Page 34 of the Bunn LCA-2 user manual — SCHEMATIC WIRING DIAGRAM LCC-2A/LCA-2A/LCA-2A, PC
Page 34 · click to enlarge
Page 34

SCHEMATIC WIRING DIAGRAM LCC-2A/LCA-2A/LCA-2A, PC

L1 N

CAPACITOR .01uF CAPACITOR .01uF

Bunn LCA-2 — SCHEMATIC WIRING DIAGRAM LCC-2A/LCA-2A/LCA-2A, PC diagram (page 34)
Fig. 23

34 34766 092706

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Bunn LCA-2

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Bunn LCA-2

Be the first to ask — other owners or our team will answer.

Original document

Bunn LCA-2 manual PDF

34 pages·1.9 MB·Beverage Dispenser·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…