EN
Bunn logo
Official user manual

Bunn DV

25 pages·3.1 MB·Beverage Dispenser·PDF·ENDEFRITNLJA
Bunn DV
Table of Contents 25 sections H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control Board · SERVICE MANUAL · BUNN-O-MATIC CORPORATION · 42311.0000E 09/13 © 2011 BUNN-O-MATIC CORPORATION · … ShowHide
Page 1 of the Bunn DV user manual — 42311.0000E 09/13 © 2011 BUNN-O-MATIC CORPORATION
Page 1 · click to enlarge
Page 1

H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control Board

Bunn DV — H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control Board diagram (page 1)
Fig. 1 · H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control B…

SERVICE MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644

To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www.bunn.com This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.

42311.0000E 09/13 © 2011 BUNN-O-MATIC CORPORATION

Page 2 of the Bunn DV user manual — H10X/H5X H5E/DV PC H5 ELEMENT With Digital Control Board
Page 2 · click to enlarge
Page 2

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor. 2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below: a) Electronic circuit and/or control boards - parts and labor for 3 years. b) Compressors on refrigeration equipment - 5 years parts and 1 year labor. c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts and labor for 4 years or 40,000 pounds of coffee, whichever comes first.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality, damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty. THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EX- PRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive op- tion while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment. THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

392, A Partner You Can Count On, Air Infusion, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, Brew- WISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic, Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design, Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, trifecta, Velocity Brew, Air Brew, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brew- er Control, Element, Milk Texturing Fusion, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Sure Tamp, Tea At Its Best, The Horizontal Red Line, Ultra are either trademarks or registered trademarks of Bunn-O-Matic Corporation. The commercial trifecta® brewer housing configuration is a trademark of Bunn-O-Matic Corporation.

2 42311 070913

Page 4 of the Bunn DV user manual — Probable Cause
Page 4 · click to enlarge
Page 4

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.

  • Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel.
  • All electronic components have 120 – 240 volt ac and low voltage dc potential on their terminals. Shorting of terminals or the application of external voltages may result in board failure.
  • Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a terminal or crimp.
  • Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water.
  • The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help to avoid twists and kinks in the tubing.
  • Make certain that all plumbing connections are sealed and electrical connections tight and isolated.
  • This dispenser is heated at all times. Keep away from combustibles.
  • WARNING
  • Exercise extreme caution when servicing electrical equipment.
  • Disconnect dispenser from the power source when servicing, except when electrical tests are specified.
  • Follow recommended service procedures
  • Replace all protective shields or safety notices

When a fault occurs (failure to the unit) the POWER lamp will

flash to identify the problem (early models)

FAULT CODES

Flashes Description of Failure 1 Temperature Sensor (short) 2 Temperature Sensor (open) 3 Refill Fault (continuous refill for 15 minutes) 4 Heater Fault (heater relay on for 120 minutes) 5 Boil Thermistor (short) H5X/H10X only 6 Boil Thermistor (open) H5X/H10X only

Er1 Temperature Sensor (short) Er2 Temperature Sensor (open) Er3 Refill Fault (continuous refill for 15 minutes) Er4 Heater Fault (heater relay on for 120 minutes) Er5 Boil Thermistor (short) H5X/H10X only) Er6 Boil Thermistor (open) H5X/H10X only)

Probable Cause

Remedy

Problem

Equipment will not operate.

1. No power or incorrect voltage

(A) Check the terminal block for the cor- rect voltage. It should be: a.) 100 to 120 volts ac across the black and white terminals for 100 to 120 volt models or, b.) 200 to 240 volts ac across the red and black terminals for 200 to 240 volt models or, c.) 230 volts ac across the red and black terminals for 230 volt models.

(B) Check circuit breakers or fuses.

42311 071310

Page 5 of the Bunn DV user manual — TROUBLESHOOTING (cont.)
Page 5 · click to enlarge
Page 5

TROUBLESHOOTING (cont.)

Problem Probable Cause Remedy

Equipment will not operate (cont.)

2. Safety overflow switch

Refer to Service – safety overflow switch for testing procedures.

Automatic refill will not oper- ate after drawing hot water.

1. No water

Check plumbing and shut-off valves.

2. Water strainer/flow control

(A) Direction of flow arrow must be point- ing towards dispenser.

(B) Remove the strainer/flow control and check for obstructions. Clear or replace.

3. Liquid level system

Refer to Service – electronic controls for testing procedures.

4. Solenoid valve

Refer to Service – solenoid valve for test- ing procedures.

Water flows into the tank con- tinuously (Dispenser discon- nected from power source).

1. Solenoid valve

Refer to Service – solenoid valve for test- ing procedures.

Water flows into the tank con- tinuously (Dispenser connect- ed to power source).

1. Liquid level system

Refer to Service – electronic controls for testing procedures.

Water is cold.

1. Safety overflow switch

Refer to Service – safety overflow switch for testing procedures.

Refer to Service – limit thermostat for testing procedures.

3. Tank heater

Refer to Service – tank heater for testing procedures.

4. Temperature control

Refer to Service – electronic controls for testing procedures.

42311 071310

Page 6 of the Bunn DV user manual — TROUBLESHOOTING (cont.)
Page 6 · click to enlarge
Page 6

TROUBLESHOOTING (cont.)

Problem Probable Cause Remedy

Water boils continuously.

1. Temperature control

Refer to Service – electronic controls for testing procedures.

2. Lime build-up

Inspect the tank assembliy for excess lime deposits. Delime as required.

Dispenser is making unusual noises.

1. Plumbing lines

Plumbing lines should not be resting on the counter top.

3. Water supply

(A) The dispenser must be connected to a cold water line.

(B) Water pressure to the dispenser must not be higher than 90 psi (620 kPa). Install a regulator if necessary to lower the work- ing pressure to approximately 50 psi (345 kPa).

Ready indicator will not light.

1. Temperature control

Refer to Service – electronic controls for testing procedures.

2. Ready Indicator LED

Replace the indicator LED.

42311 071310

Page 7 of the Bunn DV user manual — Component Access - H5E/DV-PC/X Component Access - H10X
Page 7 · click to enlarge
Page 7

SERVICE

WARNING – Disconnect the dispenser from the power source before the removal of any panel or the replacement of any component. WARNING - Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel. Disconnect the dispenser fromthe power source when servicing, except when electrical tests are required and the test procedure specifically states to connect the dispenser to the power source.

Component Access - H5E/DV-PC/X Component Access - H10X

Bunn DV — Component Access - H5E/DV-PC/X Component Access - H10X diagram (page 7)
Fig. 2 · Component Access - H5E/DV-PC/X Component Access - H1…
Bunn DV — Component Access - H5E/DV-PC/X Component Access - H10X diagram (page 7)
Fig. 3 · Component Access - H5E/DV-PC/X Component Access - H1…

The check valve, electronic control assembly, safety overflow switch, solenoid valve, overflow tube tempera- ture sensor and terminal block are located at the rear of the dispenser. Access is gained by removing the upper and lower rear panels. The upper is attached with six 8-32 slotted-head screws. The lower is attached with four 8-32 slotted-head screws. The middle panel must not be removed from the dispenser.

@ The check valve, electronic control assembly, over- flow protection switch, solenoid valve, overflow tube temperature sensor, triac assembly (EARLY MODELS ONLY) and terminal block are located on the side of the dispenser. Access is gained by removing the side panel. The panel is attached with eight 8-32 slotted- head screws.

Bunn DV — Component Access - H5E/DV-PC/X Component Access - H10X diagram (page 7)
Fig. 4 · Component Access - H5E/DV-PC/X Component Access - H1…

Faceplate Removal - H5 ELEMENT: After removing top cover, remove the two upper screws securing the faceplate. Carefully lift faceplate straight up until the three lower screws clear the key holes.

42311 022311

Page 8 of the Bunn DV user manual — BOARD AND TRIAC
Page 8 · click to enlarge
Page 8

SERVICE

Liquid Level Control Flow Charts

Electronic Controls

Bunn DV — Electronic Controls diagram (page 8)
Fig. 5 · Electronic Controls

H5E, H5X LIQUID LEVEL CONTROL

PROBLEMDoes Not Refill
Bunn DV — H5E, H5X LIQUID LEVEL CONTROL diagram (page 8)
Fig. 6

H5E, H5X LIQUID LEVEL CONTROL

PROBLEMOverflows
Bunn DV — H5E, H5X LIQUID LEVEL CONTROL diagram (page 8)
Fig. 7

BUNN 90 psig max operating pressure Strainer/Flow Control # 22300.0750 (Repl. Flow Washer #20526.0750) (Repl. Screen #23721.0000)

BOARD AND TRIAC

Location:

The electronic control board is located inside the rear of the dispenser. Access will also be needed to the temperature sensor, overflow tube temperature sensor, and liquid level probe located on the tank lid.

General:

This system controls the liquid level and water temperature of the dispenser. These two functions act independently of each other and should be tested separately.

42311 071310

Page 9 of the Bunn DV user manual — Electronic Controls (cont.)
Page 9 · click to enlarge
Page 9

Electronic Controls (cont.)

4. Remove the pink wire from terminal 5 of the elec- tronic control assembly. 5. Check the voltage across terminals 1 & 4 of the electronic control board with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 voltmodels or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models after a delay of approximately 5 seconds. 6. Disconnect the dispenser from the power source.

Liquid Level Control Test Procedure

1. Disconnect the dispenser from the power source. 2. Check the voltage across terminals 3 & 4 of the electronic control board with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models. 3. Disconnect the dispenser from the power source. If voltage was present as described, proceed to #4. If voltage was not present as described, refer to the Wiring Diagrams and check the dispenser wiring harness.

If voltage was present as described, the liquid level con- trol of the system is operating properly, proceed to #7. If voltage was not present as described, replace the electronic control board and the temperature sensor in the tank lid.

SERVICE (cont.) Temperature Control Flow Charts

Bunn DV — Electronic Controls (cont.) diagram (page 9)
Fig. 8 · Electronic Controls (cont.)
Bunn DV — Electronic Controls (cont.) diagram (page 9)
Fig. 9 · Electronic Controls (cont.)

42311 071310

Page 10 of the Bunn DV user manual — H5E THERMOSTAT
Page 10 · click to enlarge
Page 10

Electronic Controls (cont.)

7. Reconnect the pink wire to terminal 5 of the elec- tronic control assembly. 8. Loosen the compression fitting, remove the probe from the tank lid, and inspect it for mineral depos- its. Replace it if necessary. Keep the exposed ends of the probe away from any metal surface of the dispenser. 9. Check the voltage across terminals 1 & 4 of the elec- tronic control assembly with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models after a delay of approximately 5 seconds. 10. Touch the screw head end of the probe to the dis- penser housing. The indication must be 0. 11. Move the probe away from the dispenser housing. The indication must again be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models after a delay of approximately 5 seconds. 12. Disconnect the dispenser from the power source.

If voltage was not present as described, check the pink probe wire and the green ground wire for continuity and/or replace the probe.

Temperature Control Test Procedure

1. Disconnect the dispenser from the power source. 2. Check the voltage across terminals 3 & 4 of the electronic control circuit board with a voltmeter. Connect the dispenser to the power source.The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models. 3. Disconnect the dispenser from the power source. 4. Check the voltage across the tank heater terminals with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models. 5. Disconnect the dispenser from the power source.

Temperature Control Flow Charts (cont.)

If voltage was present as described, reinstall the probe, the sensing function of the system is operating properly.

H5E THERMOSTAT

H5X THERMOSTAT

PROBLEMBoils Excessively - Fills Cup
PROBLEMBoils

Red Light On While

Red Light On While

Disconnect Blue Wire From

Disconnect Blue Wire From

Control Board Pin 7

Control Board Pin 7

Show 39 more labels / short text on this page
Drain cup · Drain cup · Retry · Retry · Yes · Yes · Boiling · Replace Steam Sensor · Boiling · Replace Control Assembly · ? · ? · No · No · Yes · Still Boiling · Replace Control Assembly · ? · Retry · Retry · No · Finished · Still Boiling · Yes · Still Boiling · Yes · ? · Replace Triac Assembly · ? · Replace Triac Assembly · Check For Split · Check For Split · No · Tank Heater · No · Tank Heater · Replace Control Board · Replace Control Board · 42311 071310
Page 11 of the Bunn DV user manual — Electronic Controls (cont.)
Page 11 · click to enlarge
Page 11
Bunn DV — H5E THERMOSTAT diagram (page 11)
Fig. 10

Electronic Controls (cont.)

If voltage was present as described, the temperature control of the system is operating properly. If voltage was not present as described, contact Bunn-O-Matic to order an electronic control board and temperature sensor for evaluation and proceed to #9.

6. Replace the electronic control board.
7. Check the voltage across the tank heater terminals with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models

T3 BLK to Overflow Safety Switch T2 GRN or GRN/YEL to Chassis Ground

8. Disconnect the dispenser from the power source.

If voltage was present as described, the temperature control of the system is operating properly. Return the new electronic control board or temperature sensor to Bunn-O-Matic for credit.

J3 PNK & GRY to Heater Indicator Refill Indicator Power Indicator Ready Indicator

Electronic Controls Removal and Replacement

1. Remove all wires from the electronic control board terminals. 2. Remove the six 6-32 screws holding the electronic control board to the component bracket. 3. Disconnect the temperature sensor, overflow tube temperature sensor, and indicator wires from the electronic control board. 4. Attach the temperature sensor, overflow tube temperature sensor, and indicator wires to the electronic control assembly. 5. Fasten the new electronic control board to its bracket. 6. Refer to Fig 2 when reconnecting the wires. 7. Review the initial set-up procedures on page 6.

The H5X/H10X dispensers hold the water tempera- ture at the threshold of boiling. It is not adjustable by the user. The H5E dispenser is factory calibrated for the temperature specified on the data plate. If adjustment is required, use the following procedure:

1. Fill the dispenser according to the steps in the Initial Set-up.
2. Take the temperature of the stream of water immediately below the faucet as it flows from the dispenser with an accurate thermometer. Do not take the temperature of water collected in a container.
3. If any adjustment is required, refer to LEVEL 1 PROGRAMMING in the Operating Manual.

Adjustments · 42311 071310

Page 12 of the Bunn DV user manual — H5E THERMOSTAT
Page 12 · click to enlarge
Page 12

If voltage was present as described, reconnect the black wire and proceed to #5. If voltage was not present as described, refer to the Wir- ing Diagrams and check the dispenser wiring harness.

Limit Thermostat Location: The limit thermostat is located on the tank lid. To test the limit thermostat, access will also be needed to the terminal block located at the rear of the dispenser.

5. Check for continuity across the terminals of the limit thermostat.
Bunn DV — H5E THERMOSTAT diagram (page 12)
Fig. 11

If continuity is not present as described, the circuit is broken. Press the reset button of the limit thermostat and recheck for continuity. If continuity is not present as described, replace the limit thermostat.

Removal and Replacement: 1. Remove both wires from the limit thermostat ter- minals. 2. Remove the two #10-32 nuts attaching the limit thermostat to the top of the tank. 3. Install the new limit thermostat and secure into place with two #10-32 nuts. 4. Refer to FIG. 4 when reconnecting the wires.

Bunn DV — H5E THERMOSTAT diagram (page 12)
Fig. 12

Test Procedure: 1. Disconnect the dispenser from the power source. 2. There are two black wires on the limit thermostat terminals. One comes from the terminal block. The other goes directly to the tank heater terminal. Re- move the black wire at the limit thermostat coming from the terminal block. 3. Check the voltage across the black wire removed from the limit thermostat and the white wire or red wire of the terminal block with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models. 4. Disconnect the dispenser from the power source.

42311 071310

Page 13 of the Bunn DV user manual — H5E THERMOSTAT
Page 13 · click to enlarge
Page 13
Bunn DV — H5E THERMOSTAT diagram (page 13)
Fig. 13

Removal and Replacement: 1. Disconnect the black wires from the safety overflow switch. 2. Remove the nut beneath the copper overflow cup. 3. Remove the entire switch assembly from the cup. 4. Place the new switch assembly into the cup, wires first. Make sure that a gasket is in place around the threaded switch stem.

5. Install the nut beneath the copper overflow cup. Be sure not to overtighten. 6. Reconnect the wires, FIG. 6.
Bunn DV — H5E THERMOSTAT diagram (page 13)
Fig. 14

Location: The safety overflow switch is located inside the rear of the dispenser inside the copper overflow cup. For testing or removal of the safety overflow switch, access may also be needed by removing the two screws attaching the electronic control assembly to its mount- ing bracket.

Test Procedure: 1. Once voltage is verified at the power source, check for continuity across the safety overflow switch red wires only until the plastic float is raised and check that continuity returns when the plastic float is again lowered.

If continuity is present as described, reconnect each of the red wires to the black wires, the safety overflow switch is operating properly. If continuity is not present as described, replace the safety overflow switch.

42311 071310

Page 14 of the Bunn DV user manual — Solenoid Valve (Late Models)
Page 14 · click to enlarge
Page 14

sound after approximately 5 seconds, as the coil magnet attracts the plunger. 8. Disconnect the dispenser from the power source. 9. Reconnect the pink wire to terminal 5 of the elec- tronic control board.

Solenoid Valve (Late Models)

Location: The solenoid valve is located inside the rear of the dispenser on the right side near the bottom. To test the solenoid valve, access will also be needed to the electronic control board.

If the sound was heard as described and water will not pass through the solenoid valve, there may be a blockage in the water line before or after the solenoid valve or the solenoid valve may require inspection for wear and removal of waterborne particles. If the sound was not heard as described, replace the solenoid valve.

Bunn DV — Solenoid Valve (Late Models) diagram (page 14)
Fig. 15 · Solenoid Valve (Late Models)

Fill water tank before turning -on thermostat or connecting appliance to power source.

Use only on a properly protected circuit capable of the rated load.

Do not use near combustibles. Follow national/local electrical codes.

READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT

Removal and Replacement: 1. Remove all wires from the solenoid valve coil. 2. Turn-off the water supply to the dispenser. 3. Disconnect the water line from the solenoid valve. 4. Remove the two 8-32 slotted-head screws holding the solenoid valve and mounting bracket to the back panel. 5. Lift-out the solenoid valve. 6. Securely install the new solenoid valve to the back panel. 7. Securely fasten the water line to the solenoid valve. 8. Reconnect the wires, FIG. 8.

Test Procedure: 1. Disconnect the dispenser from the power source and turn-off the water supply to the dispenser. 2. Remove the pink wire from terminal 5 of the elec- tronic control board. 3. Check the voltage across the solenoid valve coil terminals with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models after a delay of approximately 5 seconds. 4. Disconnect the dispenser from the power source.

Bunn DV — Solenoid Valve (Late Models) diagram (page 14)
Fig. 16 · Solenoid Valve (Late Models)

If voltage was present as described, proceed to #5. If voltage was not present as described, refer to the Wir- ing Diagrams and check the dispenser wiring harness.

5. Remove both wires from the solenoid valve coil terminals. 6. Check for continuity across the solenoid valve coil terminals.

If continuity is present as described, reconnect the wires and proceed to #7. If continuity is not present as described, replace the solenoid valve coil.

7. Check the solenoid valve for coil action. Connect the dispenser to the power source. Listen carefully in the vicinity of the solenoid valve for a “clicking”

42311 071310

Page 15 of the Bunn DV user manual — Solenoid Valve (Early Models)
Page 15 · click to enlarge
Page 15

Solenoid Valve (Early Models)

If continuity is present as described, reconnect the wires and proceed to #7. If continuity is not present as described, replace the solenoid valve coil.

Location: The solenoid valve is located behind the large access panel on the left side of the dispenser. To test the solenoid valve, access will also be needed to the electronic control board.

7. Check the solenoid valve for coil action. Connect the dispenser to the power source. Listen carefully in the vicinity of the solenoid valve for a “clicking” sound after approximately 5 seconds, as the coil magnet attracts the plunger. 8. Disconnect the dispenser from the power source. 9. Reconnect the pink wire to terminal 5 of the electronic control board.
Bunn DV — Solenoid Valve (Early Models) diagram (page 15)
Fig. 17 · Solenoid Valve (Early Models)

If the sound was heard as described and water will not pass through the solenoid valve, there may be a blockage in the water line before or after the solenoid valve or the solenoid valve may require inspection for wear and removal of waterborne particles. If the sound was not heard as described, replace the solenoid valve.

Removal and Replacement: 1. Remove all wires from the solenoid valve coil. 2. Turn off the water supply to the dispenser. 3. Disconnect the water lines to and from the solenoid valve. 4. Remove the two 8-32 slotted-head screws holding the solenoid valve and mounting bracket to the component bracket. 5. Lift out the solenoid valve. 6. Remove the two 10-32 slotted-head screws holding the solenoid valve to its mounting bracket. 7. Securely install the new solenoid valve to its mount- ing bracket. The direction of flow arrow must be pointing towards the tank lid. 8. Attach the solenoid valve and mounting bracket to the component bracket. 9. Securely fasten the water lines to and from the solenoid valve. 10. Reconnect the wires, FIG. 8.

BUNN 90 psig max operating pressure Strainer/Flow Control # 22300.0750

Test Procedure: 1. Disconnect the dispenser from the power source and turn off the water supply to the dispenser. 2. Remove the pink wire from terminal 5 of the elec- tronic control board. 3. Check the voltage across the solenoid valve coil terminals with a voltmeter. Connect the dispenser to the power source. The indication must be 200 to 240 volts ac for 200 to 240 volt models after a delay of approximately 5 seconds. 4. Disconnect the dispenser from the power source.

Bunn DV — Solenoid Valve (Early Models) diagram (page 15)
Fig. 18 · Solenoid Valve (Early Models)

RED to Terminal Block RED to Control Board T4

If voltage was present as described, proceed to #5. If voltage was not present as described, refer to the Wir- ing Diagrams and check the dispenser wiring harness.

5. Remove both wires from the solenoid valve coil terminals. 6. Check for continuity across the solenoid valve coil terminals.

42311 071310

Page 16 of the Bunn DV user manual — Solenoid Valve (Early Models)
Page 16 · click to enlarge
Page 16

Tank Heater Location: The tank heater is located in the tank lid.

4. Remove the tank heater from the tank lid and inspect it for cracks in the sheath.

If the sheath shows no sign of damage, proceed to #5. If the sheath is damaged, replace the tank heater.

Bunn DV — Solenoid Valve (Early Models) diagram (page 16)
Fig. 19 · Solenoid Valve (Early Models)
5. Check for continuity across the tank heater terminals.

If continuity is present as described, reinstall the tank heater. The tank heater is operating properly. If continuity is not present as described, replace the tank heater. Removal and Replacement: 1. Remove the wires to the tank heater. 2. Remove the 8-32 nuts from the tank heater flange. 3. Remove the tank heater. 4. Inspect the tank heater gasket and replace if neces- sary. 5. Securely install the new tank heater. Be certain of a watertight seal. 6. Reconnect the wires, FIG. 10.

Bunn DV — Solenoid Valve (Early Models) diagram (page 16)
Fig. 20 · Solenoid Valve (Early Models)

BLK to Limit Thermostat BLU to Control Board Relay

Test Procedure: 1. Disconnect the dispenser from the power source. 2. Check the voltage across the terminals of the tank heater with a voltmeter. Connect the dispenser to the power source. The indication must be: a.) 100 to 120 volts ac for 100 to 120 volt models or b.) 200 to 240 volts ac for 200 to 240 volt models or c.) 230 volts ac for 230 volt models. 3. Disconnect the dispenser from the power source.

Bunn DV — Solenoid Valve (Early Models) diagram (page 16)
Fig. 21 · Solenoid Valve (Early Models)

1800W-120V 07.44 - 08.67 4000W-240V 13.43 - 15.51 4000W-208V 10.09 - 11.99 6000W-240V 08.85 - 10.23 6000W-208V 06.67 - 07.70

If voltage is present as described, proceed to #4. If voltage is not present as described, replace the tank heater.

42311 071310

Page 17 of the Bunn DV user manual — NOTE: DO NOT TEST OPERATION WITH PANELS
Page 17 · click to enlarge
Page 17

Removal and Replacement: 1. Disconnect the dispenser from the power source. 2. Disconnect the thermistor from J5 on control board. 3. Loosen the set screw and the two screws securing the two half blocks together. Remove thermistor assembly from overflow tube. 4. Install new thermistor on tube and slide down until it contacts the flared end. NOTE: It’s critical that the thermistor be centered directly under the tube opening. 5. Snug the set screw so the block assembly does not move aroung easily. 6. Connect the thermistor to J5 on control board.

Steam Sensor (Thermistor)

Location: The thermistor is located on the end of the overflow tube above the overflow cup. To test the thermistor, access will also be needed to the electronic control board.

Bunn DV — Steam Sensor (Thermistor) diagram (page 17)
Fig. 22 · Steam Sensor (Thermistor)

NOTE: DO NOT TEST OPERATION WITH PANELS

REMOVED, AS AIR MOVEMENT CAN HINDER PROPER READINGS ON THERMISTOR.

Bunn DV — NOTE: DO NOT TEST OPERATION WITH PANELS diagram (page 17)
Fig. 23

Test Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the thermistor from J5 on control board. 3. Check the resistance across thermistor with a ohmmeter. The resistance range is approximately 9K @ room temperature to approximately 2K @ 200°F. 4. Disconnect the dispenser from the power source.

Bunn DV — NOTE: DO NOT TEST OPERATION WITH PANELS diagram (page 17)
Fig. 24

If resistance was present as described, the thermistor is working. If resistance was not present as described, replace the control board.

42311 080510

Page 18 of the Bunn DV user manual — Steam Sensor (Thermistor)
Page 18 · click to enlarge
Page 18

Dispense Valve (PC Only) Location: The Dispense Valve is located behind control panel.

If voltage is not present as described, refer to Wir- ing Diagrams and check the dispenser wiring harness. Also check the control board for proper operation.

Bunn DV — Steam Sensor (Thermistor) diagram (page 18)
Fig. 25 · Steam Sensor (Thermistor)

Removal and Replacement: 1. Disconnect the dispenser from the power source and allow to cool. 2. Drain enough water from the tank so the water level is below the outlet. 3. Remove the nut and flare nut from the valve. 4. Remove the top cover, shroud, and bracket. 5. Disconnect wires from the valve. 6. Using a back up wrench to hold fitting in place, Remove the valve. 7. Wrap threads of fitting with Teflon tape and install new valve. 8. Install bracket, nut, flare nut, wires and covers.

Bunn DV — Steam Sensor (Thermistor) diagram (page 18)
Fig. 26 · Steam Sensor (Thermistor)

Test Procedures: 1. Check the valve for coil action. Turn on the valve with the dispense button. Listen carefully in the vicinity of the dispense valve for a click as the coil pulls the plunger in. If no sound is heard as described, proceed to #2. If the sound is heard as described, there may be a blockage in the valve. Disconnect the dispenser from the power source. Remove the valve and inspect for blockage, and de-lime all related areas.

2. Connect voltmeter leads to the coil terminals. Turn on the valve with the dispense button. NOTE: Due to the internally rectified coil, the indication will be 120VAC all the time. Set the meter to DC volts. The indication should be 170VDC when activated. If the polarity of meter leads are reversed, reading will indicate -170VDC. (Double these readings for 240 volt coils)

If voltage is present as described, but no coil action is observed, valve is defective. Replace valve and test again to verify repair.

FIG. 18c VALVE REPAIR KIT 18

42311 071310

Page 19 of the Bunn DV user manual — Steam Sensor (Thermistor)
Page 19 · click to enlarge
Page 19
Bunn DV — Steam Sensor (Thermistor) diagram (page 19)
Fig. 27 · Steam Sensor (Thermistor)

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

120V AC 2 WIRE + GND 120/208V AC 3 WIRE + GND 120/240V AC 3 WIRE + GND SINGLE PHASE

42311 071310 19

Page 20 of the Bunn DV user manual — Steam Sensor (Thermistor)
Page 20 · click to enlarge
Page 20
Bunn DV — Steam Sensor (Thermistor) diagram (page 20)
Fig. 28 · Steam Sensor (Thermistor)

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

42311 071310 20

Page 21 of the Bunn DV user manual — Steam Sensor (Thermistor)
Page 21 · click to enlarge
Page 21
Bunn DV — Steam Sensor (Thermistor) diagram (page 21)
Fig. 29 · Steam Sensor (Thermistor)

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

42311 121312 21

Page 22 of the Bunn DV user manual — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE
Page 22 · click to enlarge
Page 22
Bunn DV — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE diagram (page 22)
Fig. 30

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE

42311 071310 22

Page 23 of the Bunn DV user manual — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE
Page 23 · click to enlarge
Page 23
Bunn DV — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE diagram (page 23)
Fig. 31

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

100-120 VOLTS AC or 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE

42311 071310 23

Page 24 of the Bunn DV user manual — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE
Page 24 · click to enlarge
Page 24
Bunn DV — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE diagram (page 24)
Fig. 32

H5-PC NO JUMPER Early H5E, H5X, H10X Install jumper thru ver. 1.04

230 VOLTS AC 2 WIRE + GND SINGLE PHASE 40712.0000F 05/11 © 2008 BUNN-O-MATIC CORPORATION

42311 050511 24

Page 25 of the Bunn DV user manual — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE
Page 25 · click to enlarge
Page 25
Bunn DV — 200-240 VOLTS AC 2 WIRE + GND SINGLE PHASE diagram (page 25)
Fig. 33

42311 050511 25

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Bunn DV

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Bunn DV

Be the first to ask — other owners or our team will answer.

Original document

Bunn DV manual PDF

25 pages·3.1 MB·Beverage Dispenser·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…