



This section mainly introduces functions and installation guidelines of EX3 and lists the components of the aircraft and remote controller.
The Aircraft is folded inside the package. Follow the steps as below to unfold the aircraft. Step 1: Unfold the rear arms (Pic. 1). Step2: Repeat again to unfold front arms (Pic. 2).
Pic. 1 Pic. 2
Unfold the aircraft

Slide the battery into the battery compartment at the rear of the aircraft by pushing with appropriate force. Make sure that you hear a click sound indicating the battery is firmly installed.
Install the battery of remote controller
Pic. 1 Pic. 2 Pic. 3
Battery installation





This section introduces functions and features of the EX3.
Slide the button up at the right side to position “ON” (Pic.1), the aircraft is in GPS mode and can precisely position and hover by the assistance of the GPS module. When GPS signal is weak or the aircraft’s compass is interfered, the aircraft will automatically enter into Gesture Mode.
Gesture mode: OFF Slide the button down to “OFF” (Pic.2), the aircraft is in Gesture mode that GPS is not used for positioning, and the aircraft only uses the barometer to maintain altitude. The aircraft will not fly with precise positioning and hovering. Gesture mode requests pilot with good skill. In Gesture Mode, the aircraft cannot position itself or brake automatically, which increases the risk of potential flight hazards. The aircraft will be also more easily affected by its surroundings. Environmental factors such as wind can result in horizontal shifting, which may present hazards, especially when flying in confined spaces.
Pic. 1 Pic. 2



The Return-to-Home(RTH) function brings the aircraft back to the last recorded Home Point. There are 3 types of RTH: smart RTH, low battery RTH and failsafe RTH. This section describes these 3 scenarios in detail.
If a strong GPS signal (satellites over 7) was acquired before takeoff, the Home Point is the location from which the aircraft launched. The GPS signal strength is indicated by the GPS icon( ). The aircraft rear indicator lights will blink rapidly from yellow color to green color when the home point is recorded.
GPS Description · Home Point

Use the RTH button on the remote controller or tap the RTH button in the “X-DRONE” APP and follow the on-screen instructions when GPS(more than 7 satellites is presented) is available to initiate Smart RTH. During the smart RTH, you can use the remote controller to guide the aircraft around obstacles. You can press the RTH button again to exit RTH procedure and regain control of the aircraft.
The low battery level failsafe is triggered when the Eachine intelligent battery is depleted to a point that may affect the safe return of the aircraft. Users are advised to return home or land the aircraft immediately when prompted.
2. When the aircraft rear lights flash slowly, battery icon “ ” is shown on the remote controller or on the “X-DRONE” APP. And steady “beep..beep...beep” sound is heard. At this moment, the aircraft will automatically return to the Home Point if the flying altitude is beyond 15 meters or the flying distance against the home point is beyond 15 meters. If the aircraft flying altitude is less than 15 meters or the flying distance is less than 15 meters, the aircraft will automatically land to the ground.
! Attention: When the aircraft is automatically return home with Low Battery RTH function activated, you can not cancel the RTH procedure by pressing the RTH button to regain control of the aircraft.
If the Home Point was successfully recorded and the compass is functioning normally, Failsafe RTH will be automatically activated if the remote controller signal is lost beyond 6 seconds. Return-to-Home can be cancelled by the pilot, allowing them to regain control when the remote controller signal connection is re-established.
Smart RTH · Low Battery RTH · Failsafe RTH

Made up by camera ①, camera ② and ultrasonic sensor ③, the Vision System locates at front bottom of your EX3. It is a positioning system that is combined by image sensor and ultrasonic sensor. Your EX3 acquires its location and perceives obstacles through using the camera sensor to detect the ground texture and visible features. Meanwhile, assisted by the ultrasonic sensor, your EX3 could determine the altitude where it stays, which could better insure the fly safety and gain precise positioning.
Detection range Detection range of Vision System indicates as below. Your EX3's detection function will be not so effective that it could not avoid the obstacles that is out of its detection range. You have to be careful once you fly when your EX3 is not flying within its detection range.
Positioning System function The Positioning System is typically used in indoor environment when GPS is weak or unavailable. It works best when the aircraft altitude is less than 10 meters.

! The precision of the vision system is easily affected by the light strength and features of the surface textures. It would happen that the ultrasonic sensor could work normally to detect the altitude when it is flying over objects that is made by sound-absorbing materials. Once the image sensor and ultrasonic sensor are both not available, your aircraft will switch to Gesture mode automatically. Be cautious to operate the aircraft in the following situation: 1. Fly fast at an altitude below 0.5m. 2. Fly over monochrome surfaces (like pure black, pure red, pure red and pure green). 3. Fly over strong light reflective surfaces or surfaces prone to reflection. 4. Fly over water or transparent object surfaces. 5. Fly over moving object surfaces (such as crowds, swaying juggles and glass). 6. Fly over an area where light changes dramatically and rapidly. 7. Fly over surfaces extremely dark (lux10,000). 8. Fly over material surfaces that is good at absorbing ultrasonic waves (like thick carpet). 9. Fly over surfaces without clear textures. 10. Fly over surfaces with highly repeating textures (small grid brick in the same color). 11. Fly over surfaces that are tilting over 30 degrees (could not receive the echo of the ultrasonic wave). 12. Flying speed should be controlled not to be too fast. When the aircraft is 1 meter against the ground, the flying speed should not be over 5m/s; When the aircraft is 2 meter against the ground, the flying speed should not be over 14m/s.
! Attention: Keep animals away from the aircraft when the vision system is activated. The ultrasonic sensor emits high frequency sounds that are audible to some animals.


Once battery is installed firmly, press on the power switch for 3 seconds, the aircraft makes beep sounds and the lights keep flashing.
Press on the power switch for 3 seconds, the aircraft lights go off and the EX3 turns off.

! ● Need adult supervision when this aircraft is being played by children.
potential hazard, such as damage to the cable or cord, plug, enclosure of other
parts and that in the event of such damage, the product must not be used until that
damage had been properly removed.
Install propeller A and propeller B on the corresponding motor shaft and fix the rotor propellers tightly by rotating clockwise. (A/B mark are at the bottom of the propeller.)
B A
Attach the propellers

Detach the propellers Take out the screws by rotating counter-clockwise and then remove the propellers.



This section describes the features of the remote controller, including the instruction on controlling the EX3.
Choose the flight mode by switching the GPS button to ON/OFF position.

Remote controller battery level
No.
Signal strength indicator changes circularly from weak to strong.
The remote controller is under signal connection status.
Indicator lights flash slowly with steady “beep beep... beep beep” sound and the battery legend “ ” on LCD display flashing.
The remote controller is in low voltage status. Please change a full charged battery.
Battery legend “ ” on LCD display is as shown, with steady “beep beep beep...beep beep beep” sound.
Battery is running out “ ”; the aircraft will return when the altitude is over 100m or the distance is over 300m.
Battery is low “ ” ; the aircraft will return when the altitude is over 15m or the distance is over 15m; if either the flying altitude or flying distance is less than 15m, the aircraft will land to the spot.
Battery legend “ ” on LCD display is as shown, with steady long beep sound.
Signal strength on LCD display is less than two grids or no displaying, with steady long beep sound.

Gimbal trimmer The camera angle can be adjusted within a 90 degree range by operating the gimbal trimmer to obtain a better aerial experience. When scroll up the gimbal trimmer(upward to direction of “A”), the camera will tilt upward to the direction of A; when scroll down the gimbal trimmer(downward to direction of “B”), the camera will tilt downward to the direction of B.
B
A
B The camera can be rotated by 90 degrees.
Photo/Video Short-press the button indicated as below and the camera icon “ ” on the LCD screen flashes once, the camera takes one photo; Long-press the same button, the video icon “ ” on the LCD screen flashes slowly, the camera is taking video. Long-press again will exit shooting.
! Attention: When the aircraft is not inserted with TF card or the TF card is malfunction, photos and videos taking can not be done by pressing the button of the remote controller, but by the icon on the APP interface.
90° · One-key takeoff/landing

1. When the battery icon “ ” is shown on the LCD screen or on the “X-DRONE” APP, and the aircraft front lights glow solid on and the rear lights keep flashing slowly, it means that the battery is nearly low voltage. 2. When the battery icon “ ” is shown on the LCD screen or on the “X-DRONE” APP, and the aircraft front lights glow solid on and the rear lights keep flashing rapidly, it means that the battery is in low voltage.
Pic. 1 Pic. 2
Signal strength “ ” shows the strength of the received signal. The more, the better.
Smart RTH button · Low battery warning · Signal strength indicator

To obtain a satisfied flight experience, please make sure that your EX3 is flying ahead of the remote controller and no obstacles between the aircraft and the remote controller.
Leftward/ Rightward flight control Turn Left/ Right control
Leftward/ Rightward flight control
Turn Left/ Right control
Mode 2 Mode 1
Mode 1: The right stick serves as the throttle. Mode 2: The left stick serves as the throttle.
How to change throttle mode


! Attention: To change the stick mode of the remote controller, please make sure that the remote controller is under signal connection status (the indicator light keep flashing). If not, the stick mode could not be changed.


This section introduces how to download the “X-DRONE” APP and connect with mobile device.

How to link the “X-DRONE” to the camera
Power on the aircraft, then enter phone settings option. Turn on WiFi, find drone**** on the list and connect it. When “ ” legend is shown, it means WiFi connecting is successful. Exit settings and tap “X-DRONE” APP at your mobile device, then select your aircraft model on the home page; click “ ” to enter into the real-time image transmission interface.
Tap “X-DRONE” App Connect WIFI
Photos and video saving feature
Real-time image quality and FPV distance depend on your smart phone and flight environment. To obtain the best live view, please choose a wide open area to fly in. As tested, the EX3 could transmit 2K videos up to 800 meters (0.6 mile) in an environment with no interference.
Farther.Faster.Clearer

This section introduces safe flight requirements and basic aircraft operations.
1. Please don’t fly in such bad weather conditions as high temperature, snow, strong wind (≥level 5), rain or fog. 2. Always choose a wide open area for every flight. Tall structures and large metal structures may affect the accuracy of the onboard compass and GPS system. 3. Well away from people and property. Never fly directly over people or animals. 4. To minimize interference, please do not fly the aircraft in locations near power lines, base stations, electrical substations and broadcasting towers. 5. Aircraft and battery performance is subject to environment factors like temperature. Be very careful when flying over 6KM above sea level since the performance will be affected. 6. Your EX3 cannot use GPS within the polar regions.
Flight limits and GEO zones
Abide by all laws and regulations when flying your EX3. Flight limitations are applied by default to help users operate this product safely and legally. Flight limitations include altitude limits, distance limits and GEO Zones. Altitude limits, distance limits and GEO Zones function concurrently to manage flight safety when operating in GPS Mode.
All Flight Limits and GEO Zones are listed on Eachine official website www.mjxrc.net The Zones are divided into different categories and include locations such as airport, flying fields where manned aircraft operate at low altitude, border between countries, and sensitive location such as power plants.
The aircraft will be banned or restricted in the no-fly zone. “X-DRONE” APP will send out the corresponding warning. Please pay attention to it at all times.
No-fly zone

Signal connection between the aircraft and remote controller
Pic. 1 Pic. 2
After signal connection, the aircraft enters into initialization detection procedure with front and rear lights flashing red, green and yellow alternatively. Make sure that the aircraft is set on a flat and still surface for the initialization detection. The aircraft initialization detection takes about 8 seconds. Once the remote controller sends out “Di Di” sounds and the aircraft front and rear lights flash yellow alternatively, initialization detection is completed.
Aircraft initialization detection

! Attention: Make sure that the aircraft is set on a flat and still surface for the initialization detection.
Aircraft compass calibration 1. Compass calibration should be performed after successful aircraft initialization detection. 2. Aircraft compass calibration should be done for every flight. That is to say, if changing new battery or the battery is reinstalled, compass calibration should be done again.
Two steps of compass calibration: Step 1: Horizontal calibration After successful aircraft initialization detection, the aircraft front and rear lights flash yellow alternatively. Hold the aircraft horizontally and rotate it 360 degrees along the central axis for about 3 circles. The aircraft front and rear light will change from flashing yellow alternatively to flashing green alternatively when horizontal calibration is completed.

!
After the aircraft and the remote controller are banded, set the aircraft on flat ground and follow the indication photo as below to calibrate the gyro. Once the aircraft front lights turn from flashing to solid on, it means that the gyro calibration is succeeded.
How to lock and unlock the aircraft
Gyroscope calibration


Method 2: After the aircraft lands on the ground, pull down the throttle stick to the bottom position and keep for 3 seconds, the motors will stop rotating and the aircraft is locked.
Warm tips:Please do not lock the aircraft by pressing the “ ” button directly during the flight, or the aircraft will be crashed.

Basic flight operation steps
1. Place the aircraft in a wide open area that its front is your front. 2. Turn on the aircraft and remote controller. 3. Connect the remote controller with the aircraft and then proceed aircraft initialization detection. 4. Connect the EX3 with your phone and enter into the image transmission interface. 5. Unlock the aircraft after the gyro detection of the aircraft is completed. 6. Pull up the throttle stick then the aircraft takes off, and control the aircraft flight by left/right stick. 7. Pull down the throttle stick to land the aircraft. 8. Pull down the throttle stick to the bottom position and keep for 3 seconds to lock the aircraft. 9. Pull out the battery from the aircraft and then turn off the remote controller.
Video suggestion and tips
Please bear proper operation and flight safety guidelines in mind as it is very important for all of us. For more information, please turn to Appendix.



Operating Frequency 2.4-2.4835GHz 5.15-5.35GHz
Transmission Power (EIRP) 2.4GHZ≤20dBm 5GHz≤16dBm
Image Sensor 1/3 “ CMOS; Effective Pixel: 2 million
Electronic Shutter Speed Electronic Shutter: 1/30s-1/10000s
2K: 2048X1152
Color Mode RGB Mode
Supported File System FAT32
Video Format MP4, Compressed Format H.264
SD Cards Support Class 10 Micro SD card up to 32G. ≥ Class 10 Micro SD Cards
Operating Temperature 0℃-40℃
Operating Frequency 2.4-2.4835GHz
1.6km
Operating Temperature 0℃-40℃
Transmission Power (EIRP) 2.4GHz≤20dBm

Rated Power 15.2W
Operating Temperature LiPo 2S
Energy 25.84Wh
Net Weight about 297g
Charging Temperature Range 5℃-40℃
Charging Time 270 minutes
Image Transmission System WIFI 5GHz
Real-time Image Transmission 720p@20fps
Required Operating System iOS 9.0 or later Android4.4 or later


Aircraft *1 Remote Controller *1 Extra Propellers Set *1

Hobby grade radio control aircraft is somewhat considered to be the highest danger potential article. Users should firmly uphold the principle of “safety comes first”. Never fly the aircraft near airports, above crowds or in zones storing dangerous goods and understand the responsibility of the accident may cause by improper operations.


a) Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
b) This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.