





SELECT MODE SELECT TEMPERATURE

NOT SURE WHAT A FUNCTION DOES? Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.
• · •

NOTES FOR USING REMOTE CONTROL
Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.
The device could comply with the local national regulations. In Canada, it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
For optimum product performance: • Do not mix old and new batteries, or batteries of different types.
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

Scrolls through operation modes as follows: AUTO COOL
Increases temperate in 0.5°C (1°F) increments. Max. temperature is 30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.
Used to detect the people activities in the room to save energy.
Used to confirm the selected functions.
Set timer to turn unit on or off
Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%)
The selected symbol will flash on the display area, press the OK button to confirm.
mode ECO
Adjust the room humidity during Dry operation in a range of 35%~85%. Press this button to increase the humidity in 5% increments. NOTE: After setting, the humidity settings will display on the screen.
LED
urns indoor unit’s LED display and air conditioner buzzer on and off, which create a comfortable and quiet environment.
Press the TEMP or button to increase/decrease the fan speed in 1% increments.
Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.
Enables unit to reach preset temperature in shortest possible time.
Model:
RG10L(G2HS)/BGEF and RG10L(G2HS)/BGEFU1(Fresh feature is not available) RG10L1(G2HS)/BGEF,RG10L1(G2HS)/BGEFU1 RG10L10(G2HS)/BGEF(20-28 C/68-82 F)
Eco Intelligent eye · Previous setting


Scrolls through operation modes as follows: AUTO COOL
Increases temperate in 0.5°C (1°F) increments. Max. temperature is 30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.
Used to select wind flow follow people feature or wind flow away from people feature.
OK Used to confirm the selected functions.
Set timer to turn unit on or off
Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%)
The selected symbol will flash on the display area, press the OK button to confirm.
mode ECO
Adjust the room humidity during Dry operation in a range of 35%~85%. Press this button to increase the humidity in 5% increments. NOTE: After setting, the humidity settings will display on the screen.
Turns indoor unit’s LED display and air conditioner buzzer on and off, which create a comfortable and quiet environment.
Press the TEMP or button to increase/decrease the fan speed in 1% increments.
Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.
Enables unit to reach preset temperature in shortest possible time.
Model:
RG10P(G2HS)/BGEF and RG10P(G2HS)/BGEFU1(Fresh feature is not available) RG10P1(G2HS)/BGEF,RG10P1(G2HS)/BGEFU1
Intelligent eye function · Previous setting

ON/OFF Turns the unit on or off. MODE
Scrolls through operation modes as follows: AUTO COOL
Increases temperate in 0.5°C (1°F) increments. Max. temperature is 30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.
Used to detect the people activities in the room to save energy.
Used to confirm the selected functions.
SET Scrolls through operation
Set timer to turn unit on or off
clean( ) Fresh( )
Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%)
Sleep( ) Follow Me( )
AP mode ( ) Breeze
away( )
The selected symbol will flash on the display area, press the OK button to confirm.
mode ECO
Adjust the room humidity during Dry operation in a range of 35%~85%. Press this button to increase the humidity in 5% increments. NOTE: After setting, the humidity settings will display on the screen.
Decreases temperature in 0.5 C(1 F) increments.
O O Min. temperature is
O O 16 C(60 F).
Selects fan speeds in the following order: AU
20% 60% 40% 80% 100%.
Turns indoor unit’s LED display and air conditioner buzzer on and off, which create a comfortable and quiet environment.
Press the TEMP or button to increase/decrease the fan speed in 1% increments.
Enables unit to reach preset temperature in shortest possible time.
Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.
Model:
RG10L(D2HS)/BGEF and RG10L(D2HS)/BGEFU1(Fresh feature is not available) RG10L1(D2HS)/BGEF,RG10L1(D2HS)/BGEFU1
Eco Intelligent eye · Active · Previous setting

Information are displayed when the remote controller is power up.

Wireless control feature display (some units) Low battery detection display(If flashes)
Lights up when remote sends signal to indoor unit
Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.
This fan speed can not be adjusted in AUTO or DRY mode.
35% -85% This display is blank when operating in FAN mode.

Before operation, please ensure the unit is plugged in and power is available. ATTENTION
Select AUTO mode Set your desired temperature
Turn on the air conditioner
Select COOL/HEAT mode Set the temperature Turn on the air conditioner Set the fan speed
DRY Mode
Select DRY mode Set your desired temperature Turn on the air conditioner
Select FAN mode Turn on the air conditioner
Set the fan speed

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
Press TIMER button to initiate the ON time sequence. Press Temp. up or down button for for multiple times to set the desired time to turn on the unit.
Point remote to unit and wait 1sec, the TIMER ON will be activated.
ON/OFF
SLEEP
FAN
TIMER OFF TEMP
TIMER ON
SHORT CUT
TIMER OFF setting
Press TIMER button to initiate the OFF time sequence. Point remote to unit and wait 1sec, the TIMER OFF will be activated.
Press Temp. up or down button for for multiple times to set the desired time to turn off the unit.
ON/OFF
SHORT CUT
SLEEP
FAN
TIMER OFF TEMP
TIMER ON
NOTE: 1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24. 2. Cancel either function by setting its timer to 0.0h.
Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.
3:30PM

Current time 1PM


The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop.
Keep pressing this button more than 2 seconds, the vertical louver swing function is activated. (Model dependent)
If continue to press the SWING button, five different airflow directions can be set. The louver can be move at a certain range each time you press the button. Press the button until the direction you prefer is reached(some u nits only).

Press LED button Press this button more than 5 seconds(some units)
Keep pressing this button more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again will revert back to display the setting temperature.
Press this button to turn on and turn off the display on the indoor unit.

Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%) Previous setting mode ECO
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.
O
O O O
O
O
GEAR operation: Press the ECO/GEAR button to enter the GEAR operation as following: 75%(up to 75% electrial energy consumption)
50%(up to 50% electrial energy consumption)
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between electical energy consumption and set temperature.
Under ECO Intelligent eye mode, with the built-in infrared sensor, the unit can detect the people’s activities in the room. In Cooling mode ,when you are away for 30 minutes, the unit automatically lowers the frequency to save energy (for inverter models only). And the unit will automatically resume operation if sensing human activity again.
Press this button

2s Keep pressing Fan button for more than 2 seconds to activate/disable Silence function(some units).
Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.
O Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F(for models RG10L10(G2HS)/BGEF & RG10L10(D2HS)/BGEF only).
The unit will operate at high fan speed (while compressor on) with temperature automatically set to 8 C/46 F.
Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F(for model RG10L10(G2HS)/BGEF& RG10L10(D2HS)/BGEF) to activate FP function.Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
5s 5s
+
Press together Turbo button and Humidity button at the same time more than 5 seconds to activate Lock function. All buttons will not response except pressing these two buttons for two seconds again to disable locking.
When you select Boost feature in COOL mode, the unit will blow cool air with strongest wind setting to jump-start the cooling process.
When you select Boost feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.
Press Turbo button

Under Intelligent eye mode, with the built-in infrared sensor, the unit can detect the people’s activities in the room. The wind can flow away from people, but also can follow people.In Cooling mode ,when you are away for 30 minutes, the unit automatically lowers the frequency to save energy(for inverter models only). And the unit will automatically resume operation if sensing human activity again. For details, please see “ Intelligent Eye operation ” in “Owner’s Manual & Installation Manual” .

Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows: Breeze away ( ) Active clean/Self clean ( ) Fresh ( ) Sleep( ) Follow Me( ) AP mode ( ) Breeze away [ ]: Model dependent
*
Active clean function( ) (some units) :
This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.
The Active Clean Technology washes away dust, mold, and grease that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit will turn off automatically and cancel CLEAN function.
NTOE: This feature is available under cool, Fan and Dry mode only.
Press this button

Follow me function( ) : The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
Airborne bacteria can grow in the moisture that condenses around heat exchanger in the unit. With regular use, most of this moisture is evaporated from the unit. Under Self clean operation, the unit unit will clean itself automatically. After cleaning, the unit will turn off automatically. Note: You can only activate this function in COOL or DRY mode.
When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air
If the memory feature is activated, On displays for 3 seconds on the screen.
,
,
,
, If the memory feature is stopped, OF displays for 3 seconds on the screen. While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.
,
,
The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable). This function can only be activated via remote control.
,, ,,
For the detail, see sleep operation in USER S MANUAL. ,
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
in FAN or DRY mode.
,


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.