Instruction/ maintenance manual of the product RS82 Bulldog Security
Go to page of 8
CONTENTS REMOTE ST AR TER MODEL RS82 INST ALL A TION GUIDE • O WNER’S GUIDE T echnical Assistance All tech personnel are expertly qualified to answer any technical questions. T echnicians are available Monday through Friday from 9:00 a.m. until 8:00 p.
SYSTEM FEA TURES SYSTEM COMPONENTS TECHNIC AL ASSIST AN CE Should you need help. F irst chec k our websit e at www .bulldogsecurity.com/wires.htm or call our toll-fr ee T ech Support Hotline Monda y through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-8 78-8007.
MAKIN G WIRIN G CONNECTIONS 1. S tr ip back two inches of insulation on the wir e from the k ey less entry . 2. Strip back one inch of insulation on t he wir e you need to connect to. One Inch of Bar e W ire T wo Inches of Bare Wire 3. Separ at e the v ehicle wir e as shown.
4. Insert the wir e from t he unit through the hole as shown. 6. Use electr ical tape to wr ap. Be sur e to co v er the wir e about two inches on either side of t he connection. First pull t he wir e that you ha ve just connect ed along side the wir e you connected to, tape and wire tie t hem toget her.
A CCESSOR Y WIRE(S) THA T POWER THE HEA TER/BLO WER MOTOR (+12V in run or on positions) This wire is also in t he main ignition switch har ness usuall y located in the st eer ing column. Make all connections as close t o the ignition switch har ness as possible.
5 Note: R emove an y paint below the spade connector . F actory Bolt Spade Connector Black Ground W ire CHASSIS GR OUND Locate an easy to ge t to bolt or scre w located under t he dr iver’s side of t he dash and attach the BLACK g round wire from the 11-pin har ness secur el y as pictured.
6 MECHANICAL NEUTRAL S AFET Y S WITCH (Rear Wheel Dr iv e Onl y) When installing a Bulldog remo t e starter on GM v ehicles or Dodge Dak otas built prior to 1996, you must: Use the diagr am below to cr eate a circuit that will pr e v ent t he r emote s tart er from starting the v ehicle unless t he k e y is r emov ed from t he ignition switc h.
7 FOR GENERAL MOTORS CARS ONL Y Syst em 1 : P ASSKEY I and II syst em (1985 and up). This system has a r esistor pill in t he ke y . Measure r esistance of the pill using a volt/ohm meter. A bypass module is a v ailable, part #V ATS- WR module. Syst em 2 : P ASSLOCK I and II syst em (1995 and up).
An important point after buying a device Bulldog Security RS82 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bulldog Security RS82 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bulldog Security RS82 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bulldog Security RS82 you will learn all the available features of the product, as well as information on its operation. The information that you get Bulldog Security RS82 will certainly help you make a decision on the purchase.
If you already are a holder of Bulldog Security RS82, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bulldog Security RS82.
However, one of the most important roles played by the user manual is to help in solving problems with Bulldog Security RS82. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bulldog Security RS82 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
