EN
Official user manual

CODE3 V2V Sync Module

4 pages·193 KB·Automotive·PDF·ENDEFRITNLJA
CODE3 V2V Sync Module
Table of Contents 14 sections Installation and Operation Instructions · V2V Sync Module · Specifications · Sytem Requirements · … ShowHide
Page 1 of the CODE3 V2V Sync Module user manual — Sytem Requirements
Page 1 · click to enlarge
Page 1

Installation and Operation Instructions

V2V Sync Module

Do not install and/or operate this safety product unless you have read and understood the safety information contained in this manual.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the safety of emergency personnel and the public. 2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical connections. 3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or severe vehicle damage, including fire. 4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without losing eye contact with the roadway. 5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact. 6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other obstructions. 7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal. Never take the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an intersection, drive against traffic, respond at a high rate of speed, or walk on or around traffic lanes. 8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.

Specifications

Size1.875” X 1.875” X 0.75”

Additional Matrix Resources Product Information: www.code3esg.com/us/en/products/matrix Training Videos: www.youtube.com/c/Code3Inc Matrix Software: http://software.code3esg.global/updater/matrix/downloads/Matrix.exe

Input Voltage12-24 VDC

*V2V is compatible with Matrix v3.5.0 or newer.

Temp. Range-40ºC to 65ºC [-40ºF to 149ºF]

Sytem Requirements

Firmware Requirements: Z3 Siren Firmware: Siren Node: v2.0 or newer (June 2021 or newer) Network Node: v2.0 or newer (June 2021 or newer) *Older sirens are not compatible and will need to be manually flashed.

Lightbar FirmwareLBC: v1.50 Light Engines: v1.37
Software RequirementsMatrix v3.5.0 or newer
Page 2 of the CODE3 V2V Sync Module user manual — Configuring the System
Page 2 · click to enlarge
Page 2

Unpacking and Pre-Installation

Carefully remove the product and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or parts are missing, contact the transit company or Code 3. Do not use damaged or broken parts.

Ensure the product voltage is compatible with the planned installation.

Installation and Mounting

Before proceeding with installation, plan all wiring and cable routing. Select the mounting location for the product on a flat, smooth surface.

Mount unit with a clear view of the sky on the inside of the vehicle. Possible locations are on top of the dashboard or attached to the vehicle’s windshield. The unit should not come in direct contact with water. Mount such that the operation of the vehicle is not impeded. Ensure that no part of this installation interferes with airbag operation.

The V2V unit can be installed using VHB or mounting with screws. VHB tape has been included to mount the system to a dashboard or interior windshield. Ensure the surface is cleaned first by using the supplied alcohol and primer. For screw-mounting, use the supplied screws and mount the V2V unit on a flat surface using the two flanges on each side of the housing.

Wiring Instructions

Notes: 1. Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g., 3M Scotchlock type connectors). 2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. All wiring should conform to the minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation hardware should be used to anchor and protect all wiring. 3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices. 4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these points from corrosion and loss of conductivity. 5. Ground termination should only be made to substantial chassis components, preferably directly to the vehicle battery. 6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot environments or operated close to their capacity.

The V2V Sync Module, when installed, allows for multiple vehicles to synchronize Matrix flash patterns, regardless of distance. This unit is not designed to work with with competitor products.

CODE3 V2V Sync Module — Wiring Instructions diagram (page 2)
Fig. 1 · Wiring Instructions

The V2V Sync Module will need to be connected to the central node of the Matrix system, such as be a SIB or Matrix Z3 siren. Connect the supplied cable to the AUX 4-pin connector on the central node.

If using multiple auxiliary devices, such as an OBDII unit, please use the V2V-SPLIT accessory.

If a longer cable is required to reach the desired mounting location, please use V2V-EXT - 2.5M extension accessory. Multiple V2V-EXT can be used in series if needed.

Configuring the System

After fully installing all Matrix devices intended to be used in the configuration, connect the Central Node (Z3 or SIB) to a computer and open the Matrix software. Ensure that all devices are detected. Use the software to build a configuration for the system and export to the devices. The synching feature will be handled by the software if the V2V module is present when the configuration is exported.

Page 3 of the CODE3 V2V Sync Module user manual — Troubleshooting
Page 3 · click to enlarge
Page 3

Troubleshooting

All products are thoroughly tested prior to shipment. However, should you encounter a problem during installation or during the life of the product, follow the guide below for troubleshooting and repair information. If the problem cannot be rectified using the solutions given below, additional information may be obtained from the manufacturer – contact details are at the end of this document.

ProblemPossible Cause(s)Comments / Response No powerFaulty wiringEnsure connector to the central node is secure. Ensure input voltage does not exceed the range of 10-32 VDC. No communicationConnectivityIt may take a few minutes for the V2V Sync Module to establish GPS communication. Communication with the GPS satellites can have interference with buildings. Ensure the unit has an unobstructed view of the sky. During this time, the Matrix system will be able to synchronize Matrix-controlled devices on the vehicle, but vehicle-to-vehicle synching will not operate. Once GPS communication is established, vehicle-to-vehicle synching will operate automatically without any input from the end user. Not synching flash patterns between vehiclesUser setupEnsure both vehicles have Matrix systems installed with V2V sync units. Ensure both Matrix systems have been configured with V2V device installed. If chosen flash patterns have different timings or number of steps, synching may not be possible.
Page 4 of the CODE3 V2V Sync Module user manual — Product Returns:
Page 4 · click to enlarge
Page 4

Warranty

Manufacturer Limited Warranty Policy:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specifications for this product (which are avail- able from the Manufacturer upon request). This Limited Warranty extends for Thirty-six (36) months from the date of purchase.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICA- TIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WAR- RANTY.

Exclusion of Other Warranties:

MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EX- CLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.

Remedies and Limitation of Liability:

MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFACTURER’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PROD- UCT. IN NO EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IM- PROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty defines specific legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdic- tions do not allow the exclusion or limitation of incidental or consequential damages.

Product Returns:

If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods Authorization Number (RGA number) before you ship the product to Code 3®, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you use sufficient packing materials to avoid damage to the product being returned while in transit.

*Code 3®, Inc. reserves the right to repair or replace at its discretion. Code 3®, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products returned to sender after the service has been rendered.

10986 North Warson Road St. Louis, MO 63114 USA

439 Boundary Road Truganina Victoria, Australia

Unit 1, Green Park, Coal Road Seacroft, Leeds, England LS14 1FB

(314) 996-2800 c3_tech_support@code3esg.com

+61 (0)3 8336 0680 esgapsales@eccogroup.com

+44 (0)113 2375340 esguk-code3@eccogroup.com

CODE3ESG.com

CODE3ESG.com/au/en

CODE3ESG.co.uk

An ECCO SAFETY GROUP™ Brand ECCOSAFETYGROUP.com

© 2022 Code 3, Inc. all rights reserved. 920-0953-00 Rev. C

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No powerFaulty wiring p.3
No communicationConnectivity p.3
Not synching flash patterns between vehiclesUser setup p.3

Ask about the CODE3 V2V Sync Module

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the CODE3 V2V Sync Module

Be the first to ask — other owners or our team will answer.

Original document

CODE3 V2V Sync Module manual PDF

4 pages·193 KB·Automotive·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…