Instruction/ maintenance manual of the product TSTATBBPQ501 Bryant
Go to page of 21
72 72 I2:00 SET AM Tu USERS INFORMA TION MANUAL MODEL TST ATBBPQ501 5+2 DA Y PROGRAMMABLE DIGIT AL THERMOSTA T Heating & Cooling Systems NOTE TO INST ALLER: This manual must be left with the equipment user .
Ta ble Of Content s LOCA TION OF CONTROLS DISPLAY NORMAL OPERA TION Manual Thermost at Operation Time Period O peration CLOCK SET ADV ANCED SETUP P age 1 3 4 5 6 8 PROGRAMMING Setup Overview Program S.
Safety W arnings P age 2 TST A TBBPQ501 CAUTION Follow Installation Instructions carefully . DISCONNECT POWER T O THE HEATER - AIR CONDITIONER BEFORE REMOVING THE OLD THERMOST AT AND INST ALLING THE NEW THERMOST AT . W ARNING The 2 Alkaline “AA” batteries must be replaced at least every 12 months to assure proper operation.
Location of Controls P age 3 72 72 I2:00 SET AM Tu MODE SWIT CH On or Auto FAN SWIT CH UP & DOWN BUTTONS HEA T/COOL INDICA TOR Heat, Cool or Off PROGRAM SWIT CH RUN program Program OFF SET program.
Display P age 4 88 88 I2:00 SET PM AM MT uWThF SaSuHeatCool Morning Evening Night Day Day of the week. When programming, MT uWThF represents the 5 weekdays, SaSu represent the 2 weekend days. Heat and Cool indicators. In normal operation, Heat or Cool appears, reflecting the mode switch position.
P age 5 Normal Operation 72 72 I2:00 SET AM Tu Manual Operation (program switch OFF) Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand. When Fan On is selected, the fan will run continuously .
Normal Operation P age 6 72 72 I2:00 SET AM Tu MODE SWIT CH Programmed Operation (program switch RUN) Select heat or cool with the mode switch. Normally leave the fan switched to auto. In fan auto, the fan will turn on only with a heat or cool demand.
P age 7 Clock Set 6:00 PM NEXT Use these buttons to adjust the current time. Use these buttons to adjust the current day . Su Slide the program switch to the SET position. 6:00 PM Pushing and holding the Up or Down buttons will slew the time by 10s of minutes.
P age 8 Time Period Programming Program Switch RUN OFF SET PROGRAM SWIT CH Overview Slide the program switch to the SET position. The blinking icon(s) on the display may be changed by pressing the Up or Down buttons. After the blinking icon is changed how you want it, press the Next button.
P age 9 Time Period Programming Slide the program switch to the SET position. The 1st 2 steps are clock and day set, see page 7. Program RUN OFF SET Next P age 6:00 AM MT uWThF Morning NEXT Use these buttons to adjust the start time for the morning time period.
Time Period Programming P age 10 Next P age 85 8:00 SET AM MT uWThF Cool Use these buttons to adjust the cool setpoint for the day time period. Day NEXT 62 8:00 SET AM MT uWThF Heat Use these buttons to adjust the heat setpoint for the day time period.
P age 11 Time Period Programming Next P age 70 6:00 SET MT uWThF Heat Use these buttons to adjust the heat setpoint for the evening time period. Evening PM NEXT MT uWThF Use these buttons to adjust the start time for the night time period.
P age 12 Time Period Programming Next P age SaSu Use these buttons to adjust the start time for the morning time period. 6:00 Morning AM NEXT 78 SET SaSu Cool Use these buttons to adjust the cool setpoint for the morning time period.
P age 13 Time Period Programming Next P age 85 8:00 SET AM Cool Day SaSu Use these buttons to adjust the cool setpoint for the day time period. NEXT 62 8:00 SET AM Day SaSu Heat Use these buttons to adjust the heat setpoint for the day time period. NEXT 6:00 PM SaSu Use these buttons to adjust the start time for the evening time period.
P age 14 Time Period Programming Next P age 70 6:00 SET Heat Use these buttons to adjust the heat setpoint for the evening time period. Evening PM SaSu NEXT Use these buttons to adjust the start time for the night time period. Night I0:00 PM SaSu NEXT 82 SET SaSu Cool Use these buttons to adjust the cool setpoint for the night time period.
P age 15 Time Period Programming Program Switch RUN OFF SET After completion of setting the time period programming, you have 2 options: 1) Run the time period program by sliding the Program Switch to the RUN position. Or , 2) Do not run the time period program.
P age 16 Advanced Setup This is normally done by the installer at initial installation. Use these buttons to adjust the deadband from 1 to 6 degrees. Use these buttons to adjust the cycles/hour from 2 to 6. d=no limit (zoning) d1=d+no compressor lockout.
P age 17 Battery Replacement The top of the thermostat housing has two (2) screw- driver slots to assist when seperating. Repeat the procedure in the other screw driver slot. Separate the housing halves by pulling the top forward until the pins release, and then lift the bottom out.
P age 18 Battery Replacement REPLACE WITH A LKALINE BA TTERIES A T LEAST ONCE EVER Y YEAR, OR WHEN THE “LOW BA TTERY” ICON APPEARS (pages 2,17). USE “ AA ” SIZE ALKALINE BA TTERIES USE “ AA .
P age 19 W arranty THIS WARRANTY DOES NOT INCL UDE LABOR OR OTHER COSTS incurred for diagnosing , repairing, removing, installing, shipping , ser vicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer .
Programming Worksheet see page 8 Printed on recycled paper . P/N 88-403 Rev . 2 DA Y PERIOD HEA T ST ART TIME COOL Morning Morning Day Day Evening Evening Night Night Monday T uesday Wednesday Thursda.
An important point after buying a device Bryant TSTATBBPQ501 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bryant TSTATBBPQ501 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bryant TSTATBBPQ501 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bryant TSTATBBPQ501 you will learn all the available features of the product, as well as information on its operation. The information that you get Bryant TSTATBBPQ501 will certainly help you make a decision on the purchase.
If you already are a holder of Bryant TSTATBBPQ501, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bryant TSTATBBPQ501.
However, one of the most important roles played by the user manual is to help in solving problems with Bryant TSTATBBPQ501. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bryant TSTATBBPQ501 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
