Instruction/ maintenance manual of the product PSPHA732 Bryant
Go to page of 16
SMAR T TEMP ® ELECTRONIC THERMOST A T INST ALLA TION AND OPERA TING INSTRUCTIONS Mt. Laurel, New Jersey 08054, USA ● www .luxproproducts.com PSPHA732 52091 HEAT OFF COOL SET SUNDAY WEEKDAY PROGRAM .
5:36 72 T U 1. COMP A TIBILITY Y our PSPHA732 is compatible with Heat Pumps Up to 3 Stages of Heat and 2 Stages of Cooling. This includes Auxiliary and Emergency Heat. It cannot be used with 120 volt heating systems or 3 wire zone valves. Ask your dealer for other LUXPRO thermostats to control those systems.
C A U T I O N: Y our thermostat is protected against normal static electric discharges. T o minimize the risk of damaging the unit in extremely dry weather , touch a grounded metal object before touching your thermostat. 4. INST ALLATION 4.1 TOOLS REQUIRED • #1 Phillips screwdriver (small) • Drill with 3/16-in.
C A U T I O N: • Be careful not to drop the unit or disturb electronic parts. • Leave the door closed while the body is being removed from the base. 9. Route the wires through the open areas in the base plate above the terminals. Hold the base against the wall, with the wires coming through.
NOTE: If you have an electric system and the blower does not operate after installation, verify that the electric/gas option in installer set up is set to Electric, see SETUP OPTIONS. 18. Y our installation is now complete. 5. OPERA TING BASICS 5.1 UP/DOWN CHANGE KEYS • These are the two upper keys, just right of the units display .
• If a second stage of heat is called for , the flashing rate of HEA T increases • If the 3rd stage of heat activates, the display will also flash "AUX " in addition to HEA T flashing. 5.7 COOL • Use COOL mode to control your air conditioner , cooling your home.
5.12.3 CLEAN CYCLE ® • LUX’ s Clean Cycle ® allows you to program a forced air system to flow air through your system’ s filter , cleaning the air in your home, even when heating or cooling is not being utilized.
to accept the displayed start time and advance to the HEA T SET TEMPERATURE, it will flash to show that it may be edited. • The HEA T SET TEMPERATURE will be displayed on the right side of the display with the HEA T indicator visible.
0 to 60 minutes in increments of 3 minutes. Set 0 MIN/HR to allow AUTO control for particular periods while CLEAN is used in others. Set the fan duration to 60 MIN/HR to run the fan continuously for this period. • Press NEXT to advance to the next period.
• Use UP/DOWN keys to adjust the filter limit in 10-hour increments to the recommended value. • Rotate the dial to RUN to finish this setting. 7.3 ENERGY USAGE Y our thermostat records the total number of hours the thermostat has activated heating and cooling with six separate timers.
11 3 to 6 times per hour . A smaller swing number increases the number of cycles, so room temperature is more constant. A larger swing number decreases the number of cycles, saving energy in most cases. 7.6.1 SWING 1 – 1st ST AGE This setting controls when the first stage of heating or cooling turns on and off.
12 board. For reference, there are a table of settings and jumper positions printed there as well. They are described here from J3, the rightmost jumper , to J7, the leftmost jumper .
13 9.1 BA TTERY INST ALLA TION 1. Remove fresh batteries from their carton. 2. Remove body of thermostat from the wall as described in installation. 3. Remove the used batteries if present and replace them within 90 seconds to avoid having to reset the day and time.
14 12. WIRING DIAGRAMS WIRING DIAGRAM NOTES 1. Dashed wires are optional. 2. If an "E" wire was connected to your old thermostat, it should be re-connected to the "E" terminal on the new thermostat, and the optional jumper between "W" and "E" should not be used.
15 HEA T PUMP SYSTEM NEW THERMOST A T AND T APE OFF WITH COMMON TERMINAL CORRESPONDING TERMINALS NOT USED EG YY 2 R OW 1 W 2 B C L AMANA G Y1 RC-RH W1 W2 X1 AMANA PHD-2,-3,-4,or -5 G R W W1 C ARCO / F.
16 DA Y MON MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT TUES WED PERIOD HEA T TIME TEMP . TIME TEMP . COOL DA Y THURS MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT MORN DA Y EVE NIGHT FRI SA T SUN PERIOD HEA T TIME TEMP .
An important point after buying a device Bryant PSPHA732 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bryant PSPHA732 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bryant PSPHA732 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bryant PSPHA732 you will learn all the available features of the product, as well as information on its operation. The information that you get Bryant PSPHA732 will certainly help you make a decision on the purchase.
If you already are a holder of Bryant PSPHA732, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bryant PSPHA732.
However, one of the most important roles played by the user manual is to help in solving problems with Bryant PSPHA732. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bryant PSPHA732 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
