EN
Eaton logo
Official user manual

Eaton Crimp Machine (ET4001)

12 pages·363 KB·Power Tools·PDF·ENDEFRITNLJA
Eaton Crimp Machine (ET4001)
Table of Contents 8 sections Eaton ET4001 Crimp machine operator's manual · Specifications and equipment · CAUTION · Shop/Work table mounting · … ShowHide
Page 1 of the Eaton Crimp Machine (ET4001) user manual — Eaton ET4001 Crimp machine operator's manual
Page 1 · click to enlarge
Page 1

Eaton ET4001 Crimp machine operator's manual

Eaton Crimp Machine (ET4001) — Eaton ET4001 Crimp machine operator's manual diagram (page 1)
Fig. 1 · Eaton ET4001 Crimp machine operator's manual
Page 2 of the Eaton Crimp Machine (ET4001) user manual — Eaton ET4001 Crimp machine operator's manual
Page 2 · click to enlarge
Page 2
Page 2 of the Eaton Crimp Machine (ET4001) user manual — Eaton ET4001 Crimp machine operator's manual
Page 3 of the Eaton Crimp Machine (ET4001) user manual — CAUTION
Page 3 · click to enlarge
Page 3

Specifications and equipment

ET4001 Crimp machine and accessories

Eaton Crimp Machine (ET4001) — Specifications and equipment diagram (page 3)
Fig. 2 · Specifications and equipment

ET4001 is ideal for factory high performance machine operations, construction and mine locations. The ET4001 press offers crimping capabilities through 2” I.D. six spiral hose.

Weight 500 lbs.

Size 30”high, 22”deep, 12”wide

The Eaton ET4001P-002 power unit is ideally suited for use with the ET4001 press. It features a two-stage pump providing high flow at low pressure for fast ram approach and low flow at high pressure for actual crimping.

Dimensions 7½” high, 10” wide, 22” long

Weight 75 lbs.

Reservoir capacity 6 Quarts

Outlet port size ¾-16 Straight thread O-ring

Motor 1HP, 3450 RPM, 220 volts, 60 cycle, Single Phase

Hydraulic oil ISO 32 (SAE 10W)

Flow 2.6 GPM to 900 psi. 0.6 GPM above 900 psi

CAUTION

The ET4001P-002 Electric pump has the relief valve set at 5,000 psi. Damage to the press will result and the warranty may be voided if higher pressures are used. Requires individual 20 amp service breaker (220 v).

Components neededT-410-22 hose assembly (1) included in ET4001-004 package

3 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

ET4001 Crimp machine · Pressure 5000 psi

Page 4 of the Eaton Crimp Machine (ET4001) user manual — Shop/Work table mounting
Page 4 · click to enlarge
Page 4

Shop/Work table mounting

ET4001 Press and pump

Shop/Work table mounting instructions*

The following methods are offered as a guide and may be varied to suit your particular needs.

which may be used for lifting purposes (Figure 2). If these tapped holes are used, it is recommended that a minimum of two be utilized, preferably four. If two holes are used for lifting, use holes directly across from each other on the center line and not two on a diagonal. This will prevent press from tilting as it is raised.

Washers and nuts are installed from underneath. TIGHTEN.

4. Place the ET4001P-002 pump on the mounting surface to the right and slightly behind the ET4001 press. (Reference figure 8, Page 5)

Bench layout for ET4001 press

1. Prepare mounting surface for ET4001 press and pump. Refer (Figure 1) for bolt hole layout and optimum height.
Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 3 · Shop/Work table mounting
5. Mark power unit base plate hole pattern on mounting surface. Remove power unit and drill holes.

be taken to insure that the surface to which the press is bolted is capable of supporting the weight of the press (approximately 500 lbs.) and pump (approximately 75 lbs).

3. Using an adequate lifting device, raise the press to the mounting surface. Align holes in press support brackets with holes in mounting surface. Insert four ½” bolts from top of mounting surface.
6. Replace pump and align holes on mounting surface with base plate of pump. Insert bolts from top of mounting surface. Washers and nuts are installed from underneath. TIGHTEN.
2. Remove shipping carton from ET4001 press. There are four 5 / 8 -18 tapped holes in the top plate

Lifting hole layout on ET4001 press top plate

Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 4 · Shop/Work table mounting

Figure 4 Connection at top plate

7. Standing behind the press, install the # 8ORB x ORFS fitting into the top port of the crimper (Figure 4).
11. Tighten all fitting connections.
Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 5 · Shop/Work table mounting
12. Remove the tank plug and screw in reservoir vent cap. Screw black cord into switch on shroud (Figure 3). Plug electrical plug into 220 volt 20 amp circuit.
8. Screw the 90º end of the T-410-22 hose loosely onto the adapter installed in the top port (Figure 4).

Figure 5 Gauge installation

9. Remove the 08ORB plug from the D05 valve manifold mounted on the pump. Install the 90º ORB x ORFS adapter. Loosely install the straight end of the T-410-22 hose assembly. Note, you will need to orient the elbow fitting in a slight angle so the hose assembly clears the D05 valve (Figure 6).
*NOTEWhen using

Cart (part number FF 91042) holes are pre- drilled. See page 5 for photo.

Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 6 · Shop/Work table mounting
Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 7 · Shop/Work table mounting

Figure 6 Hose connection

10. Standing at the back of the machine, remove the #4 pipe plug from the center of valve manifold. Install the straight pipe nipple into the pump. Then install the #4 size, 90º elbow onto the straight adapter and the gauge into the female port of the 90º elbow fitting (Figure 5).
Eaton Crimp Machine (ET4001) — Shop/Work table mounting diagram (page 4)
Fig. 8 · Shop/Work table mounting

IT IS RECOMMENDED THAT THE PUMP BE ON AN INDIVIDUAL 20 AMP SERVICE OUTLET.

4 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Instructions · ET4001P-002 Outlet port

Page 5 of the Eaton Crimp Machine (ET4001) user manual — WARNING
Page 5 · click to enlarge
Page 5

Shop/Work table mounting and check-out procedure

Refer to safety information regarding Eaton hose, hose fittings and assembly equipment compatibility on page 2.

Figure 8 Typical ET4001 equipment set-up on shop/work table

ET4001 on FF91042 cart

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 5)
Fig. 9 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 5)
Fig. 10 · Shop/Work table mounting and check-out procedure

Cart, FF91042, holes are pre-drilled for ET4000, ET4001 or T-420 crimp machines

Check-out procedure for using electric pump ET4001P-002.

CAUTION

Throughout the Check-out procedure, check hose assembly/ adapter connections for any leaks. TIGHTEN if necessary. For-seal swivel nut torque for hose assembly; 32-35 ft. lbs.

1. Plug electric cord into a grounded (4 wire connection), 220 volt, 60 cycle, single phase outlet. IT IS RECOMMENDED THAT THE PUMP BE ON AN INDIVIDUAL 20 AMP SERVICE OUTLET.

Check oil level in power unit. The oil reservoir was filled at the factory; however, if oil is required, use ISO 32 (SAE 10W).

2. Close pusher halves on press. Due to safety interlock switch, power unit will operate only when pusher halves are closed.

WARNING

3. Hold switch until pusher touches the base adapter ring.

Do not cycle without base adapter ring in place.

4. RELEASE SWITCH. Pump and pusher will stop.
5. Move switch to the RETRACT position. The pusher will retract fully in approx. 12 to 14 seconds.
6. REPEAT STEPS 3 & 5 APPROXIMATELY SIX TIMES. This will purge the hydraulic system.

WARNING

Do not attempt to disconnect the hose sssemblies when the pusher is not fully retracted.

5 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Check out procedure

Page 6 of the Eaton Crimp Machine (ET4001) user manual — Shop/Work table mounting and check-out procedure
Page 6 · click to enlarge
Page 6

Eye protection required when press and pump are in use.

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 6)
Fig. 11 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 6)
Fig. 12 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 6)
Fig. 13 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 6)
Fig. 14 · Shop/Work table mounting and check-out procedure
1. OPEN the pusher halves. Select the proper tooling for hose type being crimped as referenced in the Eaton crimp specifications manual or chart and insert the collet assembly into the base adapter ring.
2. INSERT the hose assembly through the bottom of the base adapter ring and between the two collet assembly halves. Align the fitting with the top of the collet halves as referenced in Eaton crimp specifications.
3. PLACE the spacer ring (if applicable) in the appropriate position on top of the collet assembly (either flatside up or flat-side down as referenced in Eaton crimp specifications).
4. CLOSE the pusher halves and begin crimping by activating the pump with turning on the switch. When the pusher halves or spacer ring (if applicable) contact the base adapter ring, the crimp is complete.
5. RELEASE the switch and the pusher will stop. Move the switch to the RETRACT position to return the pusher. OPEN the pusher halves and remove the crimped hose fittings.
6. Visually inspect the crimp and verify the correct crimp diameter and crimp length.

6 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Using ET4000AR-001

Page 7 of the Eaton Crimp Machine (ET4001) user manual — Shop/Work table mounting and check-out procedure
Page 7 · click to enlarge
Page 7

Using ET4000AR-002 for heavy 4-wire and 6-wire fittings (-24 thru -32 collets)

Eye protection required when press and pump are in use.

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 15 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 16 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 17 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 18 · Shop/Work table mounting and check-out procedure
1. OPEN the pusher halves.
2. PULL the pusher tab upward. The pusher tab is located behind the top of the pushers at the back of the machine.
3. SLIDE pushers to side while holding the pusher tab up.
5. REMOVE the base adapter ring from base plate and PLACE the ET4000AR-002 base adapter ring inside the base plate.
4. PULL spacer ring locator bracket upward. TURN the locator bracket 90˚.
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 19 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 20 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 21 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 7)
Fig. 22 · Shop/Work table mounting and check-out procedure
6. TURN locator bracket 90˚ until aligned properly.
7. SELECT the proper collet assembly for hose type being crimped as referenced in the crimp specifications manual or chart and insert the collet assembly into the base adapter ring.
8. INSERT the hose assembly through the bottom of the base adapter ring and between the two collet assembly halves. To achieve a full flat crimp for 4SP/6SP fittings, locate the bottom of the socket approximately 1 / 8 " (3mm) from the bottom edge of the collet halves as referenced in Eaton crimp specifications.
9. CLOSE the pusher halves and begin crimping by activating the pump with turning on the switch. When the pusher halves or spacer ring (if applicable) contacts the base adapter ring, the crimp is complete.
10. RELEASE the switch and the pusher will stop. Move the switch to the RETRACT position to return the pusher. OPEN the pusher halves and remove the crimped hose assembly.
11. Visually inspect the crimp and verify the correct crimp diameter and crimp length.

7 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Page 8 of the Eaton Crimp Machine (ET4001) user manual — Shop/Work table mounting and check-out procedure
Page 8 · click to enlarge
Page 8

Using T-410-25 adapter ring

Eye protection required when press and pump are in use.

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 8)
Fig. 23 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 8)
Fig. 24 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 8)
Fig. 25 · Shop/Work table mounting and check-out procedure
Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 8)
Fig. 26 · Shop/Work table mounting and check-out procedure
1. OPEN pusher halves and place T-410-25 adapter ring in the base adapter ring (ET4000AR-001).
2. SELECT proper size collet (referenced in the crimp specifications manual) for hose type and size being crimped. INSERT collet halves into adapter ring. PLACE proper size hose end on hose. Be sure to bottom the hose.
3. SELECT PROPER spacer ring referenced in the crimp specifications manual. INSERT hose assembly from below, between collet halves.
4. CLOSE pusher halves. HOLD SWITCH ON. When spacer ring (shown in step 3 in black) bottoms on adapter ring below it, the crimp is complete.

PLACE appropriate side of spacer ring on top of collet with uncrimped hose assembly held in place.

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 8)
Fig. 27 · Shop/Work table mounting and check-out procedure
5. RELEASE the switch and the pusher will stop. Move the switch to the RETRACT position to return the pusher. OPEN the pusher halves and remove the crimped hose fittings.
6. Visually inspect the crimp and verify the correct crimp diameter and crimp length.

8 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Page 9 of the Eaton Crimp Machine (ET4001) user manual — Shop/Work table mounting and check-out procedure
Page 9 · click to enlarge
Page 9

Spacer ring and nominal crimp diameter measurement

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 9)
Fig. 28 · Shop/Work table mounting and check-out procedure

Typical spacer ring illustrating both sides of ring

Flat side Counterbore side

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 9)
Fig. 29 · Shop/Work table mounting and check-out procedure

Nominal crimp diameter measurement

Eaton Crimp Machine (ET4001) — Shop/Work table mounting and check-out procedure diagram (page 9)
Fig. 30 · Shop/Work table mounting and check-out procedure

Measuring crimp diameters should be a part of the normal hose assembly procedure. To insure a proper crimp diameter reading, follow these steps:

1. Measure the diameter in the middle of the crimped portion of the hose end.
2. Place the caliper in a position to allow for a measurement across the pressed (flat) portion of the crimp.
3. See crimp diameters in crimp specifications.

Collet assembly lubrication Every 30 crimps = Re-lubricate sliding surfaces of dies

Every 250 crimps = Remove old grease and re-lubricate

Base adapter ring lubrication Every 250 crimps = Remove old grease and re-lubricate

Every 1,000 crimps = Remove old grease, inspect for

wear or damage and re-lubricate if okay.

9 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Spacer ring · Maintenance

Page 10 of the Eaton Crimp Machine (ET4001) user manual — Troubleshooting procedures
Page 10 · click to enlarge
Page 10

Troubleshooting procedures

Eaton Crimp Machine (ET4001) — Troubleshooting procedures diagram (page 10)
Fig. 31 · Troubleshooting procedures
Eaton Crimp Machine (ET4001) — Troubleshooting procedures diagram (page 10)
Fig. 32 · Troubleshooting procedures

Problem Cause Solutions (page 11)

Pump/motor does not start Blown fuse; Improper electrical hookup Step #1 (cut cord, loose wire, switch malfunctions) Motor starts but blows fuses High amps; Pusher doesn’t advance; Step #1 Pump binding or scored; cold oil Replace pump Motor runs - pusher does not advance Shuttle stuck open; Pump coupling sheared; Step #4 Pump unload valve stuck open Replace pump Check valve stuck shut Step #5 Motor runs - Pusher does not advance Solenoid malfunction Step #5 Motor runs - Pusher advances Pump unload valve stuck shut Replace pump but doesn’t develop final crimp pressure, blows fuse Motor runs - Pusher advances Relief valve leaking; Step #3 but doesn’t develop final crimp pressure Shuttle valve leaking; Step #4 Relief valve set low Step #3 Pusher won’t retract Shuttle valve stuck closed Step #4 Erratic pusher movement Low oil level; Step #2, Worn seal Replace pump Noisy pump; On start up only Low room temp. - Oil too thick; Use lighter weight oil (continuous) Air leaking - Low oil Level Step #2 Oil temperature hot Having unit operate at crimping psi too long; Operate for 3 seconds at crimp pressure; Low oil level: Step #2, Pump worn (longer cycle time); Replace pump, Leaking relief valve and /or shuttle valve Step #3, #4

10 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

Front view · Back view

Page 11 of the Eaton Crimp Machine (ET4001) user manual — Repair and replacement items
Page 11 · click to enlarge
Page 11

Troubleshooting procedures

1. Check – Look for fuse, loose wire connections, switch malfunctions or damaged cord. Check for proper installation of a 220 volt circuit.

adjustment screw, spring and ball. Ball should be attached to spring. Check ball and seat for possible scoring. Replace spring and ball in cavity. Insert a small punch through spring against ball. Give punch a moderate tap to seat ball. Return adjustment screw to original position making sure adjustment screw is at least one turn from bottoming. Remove 1/4” NPTF plug from port above check valve and install a 6,000 psi pressure gage. With 6,000 psi pressure gauge in place, operate unit to full crimping position. Gauge should read approximately 5,000 psi. To raise setting, turn screw inward (clockwise); to lower, turn screw outward (counterclockwise) in ¼ turn increments. After each adjustment, recycle and read gauge for proper setting. Run a cycle of the crimping system for

final gauge reading before removing gauge and reinstalling pipe plug.

damage the O-ring seals. If cartridge disassembly is required use care in removing stem as it has a .0005 metal seal fit. Rotate stem in solvent and push from seat end to remove from cartridge. Do not lose the loose ball. Wash parts in clean solvent and examine for any surface markings. If necessary, polish with a fine crocus cloth. After final cleaning, reassembly cartridge. Shake cartridge and check for free movement of ball and stem. Replace cartridge if not functional at this point. Reassemble shuttle valve into its cavity and check crimping cycle prior to using system.

Step 4: Shuttle valve – If the shuttle valve is in a closed position and the ET4001 pusher will not retract, it may be helpful to tap the shuttle valve cap several times to dislodge any silt that may be causing the stem to bind. If this does not free the valve and allow the pusher to retract, use extreme caution prior to proceeding with shuttle valve removal as the system is still under pressure. It may be advisable to relieve pressure at a hose connection to avoid an oil bath. After pressure is removed from system, remove cap and valve cartridge. Soak cartridge in a PETROLEUM BASED SOLVENT ONLY (clean Stoddard solvent). Do not use Triethene, gasoline or paint thinner as they will

2. Check oil level – after assembly and system has been purged of air, the fluid level should be½” from top of reservoir. Clean, anti-wear type, having a 300 SSU/100˚ hydraulic oil is recommended (ISO 32 or SAE 10W). Oil is needed to:
1. Transmit power easily through system
2. Lubricate moving parts
3. Provide seal clearances between parts
4. Cool or dissipate heat
3. Clean or reset relief valve – a 6,000 psi pressure gauge, a 5/16” Allen wrench, a 1” socket and a screwdriver are required. Remove cap from relief valve. Remove

Repair and replacement items

Item Number Qty. Part number Description

1 1 T-410-1M Micro switch 2 1 ET4000AR-001 Base adapter ring 3 1 ET4000AR-002 Base adapter ring 4 1 ET4000TP-0001 Locator bracket kit 5 1 ET4000TP-0002 Wear plate kit 6 1 ET4001C-0015 Blue shroud 7 8 120-00429 Screw, hex head 8 1 ET4001C-0006* Left hand pusher assembly 9 1 ET4001C-0005* Right hand pusher assembly

* must be ordered as a pair

11 EATON ET4001 Crimp machine operator´s manual W-EQCR-TM022-E4 April 2021

ET4001 Crimp machine

Page 12 of the Eaton Crimp Machine (ET4001) user manual — Repair and replacement items
Page 12 · click to enlarge
Page 12

Eaton Hydraulics Group USA 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952-937-9800 Fax: 952-294-7722 www.eaton.com/hydraulics

Eaton Hydraulics Group Europe Route de la Longeraie 7 1110 Morges Switzerland Tel: +41 (0) 21 811 4600 Fax: +41 (0) 21 811 4601

Eaton Hydraulics Group Asia Pacific Eaton Building No.7 Lane 280 Linhong Road Changning District, Shanghai 200335 China Tel: (+86 21) 5200 0099 Fax: (+86 21) 2230 7240

© 2021 Eaton All Rights Reserved Printed in USA Document No. W-EQCR-TM022-E4 April 2021

Ask about the Eaton Crimp Machine (ET4001)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Eaton Crimp Machine (ET4001)

Be the first to ask — other owners or our team will answer.

Original document

Eaton Crimp Machine (ET4001) manual PDF

12 pages·363 KB·Power Tools·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…