EN
Whirlpool logo
Official user manual

Whirlpool COMPACTOR

16 pages·748 KB·Household Appliance·PDF·ENDEFRITNLJA
Whirlpool COMPACTOR
Table of Contents 21 sections COMPACTOR USER INSTRUCTIONS · FOR CONSOLE MODELS · W11034804A · COMPACTOR SAFETY · … ShowHide
Page 1 of the Whirlpool COMPACTOR user manual — W11034804A
Page 1 · click to enlarge
Page 1

COMPACTOR USER INSTRUCTIONS

FOR CONSOLE MODELS

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in the TROUBLESHOOTING section, please visit our website at www.whirlpool.com or call us at 1-800-253-1301. You will need your model and serial number, located on the right-hand side, behind the compactor drawer.

TABLE OF CONTENTS COMPACTOR SAFETY 2 INSTALLATION REQUIREMENTS 3 INSTALLATION INSTRUCTIONS 4 COMPACTOR USE 8 COMPACTOR CARE 10 TROUBLESHOOTING 12 WARRANTY 15

W11034804A

Page 2 of the Whirlpool COMPACTOR user manual — with a grounded receptacle. SAVE THESE INSTRUCTIONS
Page 2 · click to enlarge
Page 2

COMPACTOR SAFETY

Whirlpool COMPACTOR — COMPACTOR SAFETY diagram (page 2)
Fig. 1
  • Read all instructions before using the compactor.
  • Do not compact toxic or volatile flammable material such as
  • Close supervision is necessary when used by or near

oily rags and insect sprays. Do not compact lighted cigarettes, cigars, or other hot or burning items. Do not overload the compactor.

children. Do not allow to be used as a toy, or to run unattended at any time. Lock Key Switch when not in use and store key out of reach of children.

  • Do not take apart the compactor. Incorrect reassembly can

cause electric shock when subsequently used.

  • Do not touch moving parts.
  • Handle a loaded trash bag with care. Sharp objects can
  • Do not operate with a damaged cord set, plug, motor, or

after damage in any manner. Have the compactor examined, repaired or adjusted by an authorized serviceperson.

pierce the bag and cause injury. Do not overload trash bag with heavy material such as glass.

  • This compactor is intended for household use only.
  • Use only for intended use as described in this manual. Do
  • Unplug the compactor before servicing.

not use other than manufacturer's recommended attachments.

  • Do not modify the plug attached to the compactor; use only

with a grounded receptacle. SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

Page 3 of the Whirlpool COMPACTOR user manual — Electrical Requirements
Page 3 · click to enlarge
Page 3

INSTALLATION REQUIREMENTS

Location Requirements

Whirlpool COMPACTOR — INSTALLATION REQUIREMENTS diagram (page 3)
Fig. 2
Whirlpool COMPACTOR — INSTALLATION REQUIREMENTS diagram (page 3)
Fig. 3
341/8" 6.7 cm) 24" (8341/ 6.7 (61.0 cm

A. Leave 6" (15.2 cm) of clearance space to the right side of the compactor in order to remove the compactor bags. B. Leave 23" (58.4 cm) of clearance in front of the compactor in order to fully open or remove the compactor drawer.

Whirlpool COMPACTOR — INSTALLATION REQUIREMENTS diagram (page 3)
Fig. 4

Electrical Requirements

Whirlpool COMPACTOR — Electrical Requirements diagram (page 3)
Fig. 5 · Electrical Requirements

A 341/4" min. (87.0 cm)

A. Grounded electrical outlet must be a minimum of 3" (7.6 cm) away from surrounding cabinets or nearby walls as shown. It can be placed either to the left or the right side of the compactor.

This compactor is for use on a single phase, 115 volt, 60 Hz, AC only, 15 or 20 amp fused and properly grounded circuit, and is equipped with a grounding plug as shown below. It is recommended that a separate circuit serving only this appliance be provided. This compactor must be grounded while in use to reduce the risk of electric shock. The compactor is equipped with a three-conductor cord and 3 prong grounding-type plug to fit the proper grounding-type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Do not connect the green (or green and yellow) wire to a live terminal. Do not modify the plug attached to the compactor; use with a grounded receptacle.

Show 4 more labels / short text on this page
Clearance Dimensions · Product Dimensions · Cutout Dimensions · Recommended Grounding Method
Page 4 of the Whirlpool COMPACTOR user manual — Unpacking
Page 4 · click to enlarge
Page 4

INSTALLATION INSTRUCTIONS

Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 4)
Fig. 6

Tools Installer: Leave User Instructions with the homeowner. Homeowner: Keep User Instructions for future reference and for local electrical inspector’s use if required.

Gather the required tools and parts before starting installation:

Level Phillips No. 2 screwdriver

Tape measure Flat-head screwdriver

Pliers 5/16" box-end wrench

10. Place the drawer on the two corner posts.

Unpacking

11. Place the other two corner posts on the floor to the side of the compactor.
Whirlpool COMPACTOR — Unpacking diagram (page 4)
Fig. 7 · Unpacking
12. Grasp the sides of the compactor cabinet and place compactor on its side on top of the second set of corner posts.
13. Remove the shipping base from the bottom of the compactor.

Use two or more people to move and install compactor.

Failure to do so can result in back or other injury.

Whirlpool COMPACTOR — Unpacking diagram (page 4)
Fig. 8 · Unpacking
2. Remove all packaging materials, such as tape and shipping pads.
3. Use a mild detergent and warm water to remove waxy residue caused by shipping material.
4. Dry thoroughly with a soft cloth. For more information, see “Cleaning” in the “Compactor Use” section.
5. Be sure the power cord is attached to the cord clip on the rear of the compactor.
Whirlpool COMPACTOR — Unpacking diagram (page 4)
Fig. 9 · Unpacking

Height Adjustment Height adjustment of the rear rollers is not required for a freestanding installation. You can install a freestanding unit undercounter. For non-undercounter installation, you only need to adjust the front leveling legs and level the unit. 1. Measure the height of your cabinet opening. The top of the compactor mounting screw head should be at least 1/8" (3 mm) from the top of the cabinet opening.

The rear wheels are preset for a cabinet height of 341/4" (87 cm). See “Position 1” in the following picture. To adjust for cabinet opening heights greater than 341/4":

Loosen self-tapping screw just enough to clear stud from hole in Position 1.

6. Place two of the four corner posts from the packaging on the floor near the compactor.

Move the rear wheel and stud to Position 2 or 3 as needed for your cabinet opening measurement: Position 2: 347/16" to 3411/16" (87.5 to 88.1 cm) Position 3: 3413/16" to 35" (88.4 to 88.9 cm) NOTE: To level the compactor in position 3, you may need to add shims under the front leveling legs. The shims should be approximately 1/4" (6 mm) thick.

7. Press the foot pedal or use the handle to open the compactor drawer and remove any shipping materials or other items from the drawer.

Tighten screw.

9. Grasp the drawer handle or sides of drawer and lift drawer out of compactor.

Tools needed · Scissors Utility knife

Page 5 of the Whirlpool COMPACTOR user manual — INSTALLATION INSTRUCTIONS
Page 5 · click to enlarge
Page 5
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 5)
Fig. 10

Undercounter Installation Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and local codes and ordinances. NOTE: Installation hardware is not provided for the freestanding models. See the “Accessories” section to order a conversion kit. IMPORTANT:

Do not grasp control panel to move the compactor.

To avoid damaging floor covering, slide compactor onto cardboard or hardboard before moving compactor across floor.

2. Stand the compactor upright. Move the corner posts to the opposite side and lay the compactor on its other side. Adjust the other rear wheel.

Do not allow the rear frame of the compactor to touch the floor covering when lifting or moving compactor. 1. Move the compactor close to its final location.

3. Use pliers to lower the front leveling legs away from the compactor cabinet. Adjust the leveling legs to match the position of the rear wheels.
2. Remove cord clip from the back of the compactor. Plug into a grounded 3 prong outlet.
3. Determine if you want the compactor cabinet frame or drawer front flush with the kitchen cabinet face.

Rear Wheel position:

Position 1: 3/16" (4 mm) from bottom plate Position 2: 9/16" (14 mm) from bottom plate Position 3: 3/4" (19 mm) from bottom plate

4. Rotate the two top retaining brackets (supplied with conversion kit) 180°.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 5)
Fig. 11

3/16" (4 mm) at default position 1

The screws are supplied in position 2. If desired, adjust the brackets to position 1 or 3 as described below:

If the compactor frame is to be flush with the cabinet front, place retaining bracket screws through 1.

If the compactor drawer front is to be flush with the cabinet front, place retaining bracket screws through 3.

If the compactor is to be midway between 1 and 3, leave the retaining bracket screws through 2.

4. Stand the compactor upright. Dispose of/recycle all packaging materials.

Freestanding Installation 1. Move the compactor close to its final location.

2. Plug into a grounded 3 prong outlet.
3. Slowly move compactor into its final position.
4. Adjust the front leveling legs until the compactor is level. Repeat Step 1 if necessary.
5. Slowly lift the front slightly and roll compactor into the cabinet opening.
5. Grasp sides of compactor drawer and place the wheels of the drawer into the tracks.
6. Adjust the leveling legs until the compactor is level and stable. Place a level inside the bottom of the cabinet as shown. Check the compactor leveling side to side and front to rear.
6. Lift at the handle so drawer will go over drawer stops.
7. Close the drawer.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 5)
Fig. 12
8. Make sure the drawer opens and closes freely. If the toe plate rubs against floor, see the “Adjusting the Toe Plate” section for further instructions.
Show 4 more labels / short text on this page
Leveling leg · Bottom plate · Countertop · Retaining bracket
Page 6 of the Whirlpool COMPACTOR user manual — INSTALLATION INSTRUCTIONS
Page 6 · click to enlarge
Page 6
7. Using the two #8-18 x 1/2" (13 mm) screws (provided), fasten the retaining brackets to the countertop with the mounting screws.
3. Use a ruler and a pencil or chalk to draw a line between the marks on each side of toe guard. Use scissors or utility knife to cut toe guard along line.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 6)
Fig. 13
8. Grasp sides of compactor drawer and place the wheels of the drawer into the tracks. Lift at the handle so drawer will go over drawer stops. Close the drawer. Make sure the drawer opens and closes freely. If the toe guard rubs against floor, see “Adjusting the Toe Guard” for further instructions.
4. Replace drawer. If toe guard still rubs floor covering, repeat steps 1-3.

Custom panel thickness should be 1/2" (13 mm) to 5/8" (16 mm). A panel thicker than 5/8" will interfere with the foot pedal operation. Dimensions shown are for the short panel.

Cabinet-face Mounting (Use if countertop mounting is not possible.)

Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 6)
Fig. 14

If the toe guard rubs the floor covering, the toe guard clearance may be changed as follows: 1. Mark on each side of the toe guard the amount of toe guard that rubs the floor covering.

Dimensions shown are for the long panel. The long panel cannot use the supplied handle.

2. Remove the drawer from the compactor. (See steps 8 and 9 in the “Unpacking” section.)
Page 7 of the Whirlpool COMPACTOR user manual — INSTALLATION INSTRUCTIONS
Page 7 · click to enlarge
Page 7

Bend this tab 90 degrees as shown.

Preparing for Custom Panel Installation

Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 15
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 16

Tab orientation as supplied Tab bent 90 degrees to stop custom panel from

going below this point.

8. Place the custom panel against the container front and rest it on the tab.
9. Use 4 #8 x 1" wood screws to attach the custom panel as shown below. If you are installing the long panel (handle removed) you will have three holes available, for a total of seven screws to attach the custom panel.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 17
1. If installing the longer panel, remove the handle by removing the three screws.
2. Turn the drawer upside down for this procedure. Do not put too much pressure on the handle if turning the drawer over. It is best to place the drawer on a bench or elevated item to avoid putting pressure on the handle.
3. Remove foot pedal by removing the two screws.
10. Long Panel Only: A 3/4" quarter round molding with the following dimensions is suggested to fill the gap left by the removed handle.
4. Remove toe guard by removing the two screws.
5. Remove the four front panel screws.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 18
6. Slide the front panel out and place aside.
7. Locate the rest tab on the bottom of the drawer front panel.
Whirlpool COMPACTOR — INSTALLATION INSTRUCTIONS diagram (page 7)
Fig. 19

0.75” (19 mm) 0.75" (19 mm)

0.63" (16 mm)

0.63” (16 mm)

11. Reattach the toe guard with the two screws.
12. Reattach the foot pedal with the two screws.
Show 12 more labels / short text on this page
Handle · Front panel screws · Handle Screws · Front panel · Panel removal · in this direction · Foot pedal screws · Toe guard · Foot pedal · Toe guard scews · 3/4" Quarter round · Rest tab
Page 8 of the Whirlpool COMPACTOR user manual — Starting Your Compactor
Page 8 · click to enlarge
Page 8

COMPACTOR USE

WARNING

How Your Compactor Works The compacting ram is the part of the compactor which compresses the trash. IMPORTANT: The compacting ram stops 7" (18 cm) from the bottom of the drawer. You will not see compacting of trash until the drawer is more than half full. You may hear a noise when glass breaks. Strong glass bottles may not break. The trash in a full compactor bag will be about a quarter the size of its original bulk.

Cover glass items when compacting to better contain fragments.

Whirlpool COMPACTOR — COMPACTOR USE diagram (page 8)
Fig. 20

Failure to do so can result in cuts.

2. Place trash in compactor.
Whirlpool COMPACTOR — COMPACTOR USE diagram (page 8)
Fig. 21

Loading WARNING

Wrap or cover wet or messy trash.

Do not compact items that may develop offensive odors, such as raw meat, fish, grapefruit rinds, disposable diapers, or personal hygiene items.

Load bulky trash in the center of the drawer.

Load bottles and cans on their sides in the center of the drawer. Do not load bottles in an upright position. 3. Close the drawer.

Cut Hazard Do not push items down into compactor with hands

Starting Your Compactor

or feet.

Doing so can result in cuts.

1. Turn the Key-knob, located behind the drawer, to the On position.
Whirlpool COMPACTOR — Starting Your Compactor diagram (page 8)
Fig. 22 · Starting Your Compactor
Whirlpool COMPACTOR — Starting Your Compactor diagram (page 8)
Fig. 23 · Starting Your Compactor
2. Push the ON button.
Whirlpool COMPACTOR — Starting Your Compactor diagram (page 8)
Fig. 24 · Starting Your Compactor
3. Press the START button and a compression cycle will complete.

Cut Hazard

Page 9 of the Whirlpool COMPACTOR user manual — WARNING
Page 9 · click to enlarge
Page 9

Removing a Filled Bag

Installing a New Bag Do not use any kind of bag other than those designed specifically for use in your compactor. Order replacement compactor bags through your local dealer or by calling the toll-free number on the cover or in the “Accessories” section. IMPORTANT: Before installing a new bag, be sure:

Whirlpool COMPACTOR — Removing a Filled Bag diagram (page 9)
Fig. 25 · Removing a Filled Bag

Two people may be required to remove and transport compacted bag.

The drawer latch is securely locked.

Unlock latch to assist in the removal of the bag.

Whirlpool COMPACTOR — Removing a Filled Bag diagram (page 9)
Fig. 26 · Removing a Filled Bag

Failure to do so can result in back or other injury.

When the trash is compacted to the top of the drawer, remove the bag. If the bag is too heavy, compact less trash before emptying it in the future.

WARNING

The drawer is clean and free of debris. NOTE: An unlatched drawer can cause the drawer monitor switch to stay open. This will make the ram return and the compactor will continue to run. Attempt to push the drawer inwards to stop the compactor. The continuous running of the compactor can also be attributed to debris in the drawer area. If it is difficult to open or close the drawer, this may be due to either the drawer latch not being locked, or debris in the drawer area. 1. Place folded bag into the drawer. Open bag and pull top edges over the drawer top.

Cut Hazard Do not push items down into compactor with hands

or feet.

Doing so can result in cuts.

Whirlpool COMPACTOR — WARNING diagram (page 9)
Fig. 27
1. To open the drawer, lift and pull the handle or press the foot pedal. 2. Remove top of bag from bag retainer buttons. Pull up all four bag cuffs. Close bag with a twist tie.
Whirlpool COMPACTOR — WARNING diagram (page 9)
Fig. 28
2. Lock bag in place by pulling the four pre-punched holes over the bag retainer buttons. Holes will expand over the buttons without damaging the bag.
3. Release drawer side latch. Tilt drawer to the right. This releases pressure on the bag, making it easier to remove the bag.
3. Press inside of bag against the drawer bottom, sides and corners for a smooth fit.
Whirlpool COMPACTOR — WARNING diagram (page 9)
Fig. 29
5. Latch the drawer if it was unlatched.
Page 10 of the Whirlpool COMPACTOR user manual — Cleaning WARNING
Page 10 · click to enlarge
Page 10

COMPACTOR CARE

Remove the drawer side by lifting it out of the drawer.

Whirlpool COMPACTOR — COMPACTOR CARE diagram (page 10)
Fig. 30

Your new compactor is designed to give you many years of dependable service. However, there are a few things you are expected to do in order to properly maintain your compactor. This section will tell you how to clean and care for your compactor. NOTE: Any services other than those outlined in this section should be performed by an authorized service representative.

Cleaning WARNING

4. Wash the interior of the drawer with a clean sponge or soft cloth and a mild detergent in warm water. Rinse and dry thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted position.
6. Press the drawer latch down while pushing the drawer side to the upright position.
7. Latch the drawer side.

Wear gloves when cleaning inside the drawer or cabinet, or the ram.

8. Close the drawer.

Failure to do so can result in cuts.

Cleaning Inside the Cabinet

1. Pull the drawer out until it stops.

Before cleaning the compactor, open the drawer and turn the Key-knob to the OFF position and remove it.

Whirlpool COMPACTOR — Cleaning WARNING diagram (page 10)
Fig. 31 · Cleaning WARNING
1. Wash exterior surfaces (including stainless steel) with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Rinse and dry thoroughly with a soft cloth.
2. Wipe up spills immediately. Some foods can damage the finish if left on the compactor surface.

Cleaning Inside the Drawer

1. Pull drawer out until it stops.
2. Remove the bag. See the “Removing a Filled Bag” section.
3. Optional: Remove the drawer side. Hold the drawer latch open and tilt the side of the drawer out until the latch clears the drawer front.
3. Grasp the handle or drawer on the sides and pull it out the rest of the way. Set the drawer down gently.
Whirlpool COMPACTOR — Cleaning WARNING diagram (page 10)
Fig. 32 · Cleaning WARNING

Cut Hazard · Cleaning Exterior Surfaces

Page 11 of the Whirlpool COMPACTOR user manual — COMPACTOR CARE
Page 11 · click to enlarge
Page 11
4. Vacuum the inside of the cabinet. Liquid spills or wet trash should be cleaned up by hand, or by using a vacuum designed to pick up liquids.

Accessories To order, contact your local authorized dealer. In the U.S.A. visit our webpage www.whirlpool.com or call 1-800-253-1301. In Canada, visit our webpage www.whirlpoolparts.ca or call: 1-800-807-6777. Replacement bags 15-pack - Part Number W10165295RP 60-pack - Part Number W10165294RB 180-pack - Part Number W10165295BU Bag Carrier Service - Part Number 13030RP Installation Hardware Freestanding to Undercounter: Conversion Kit - Part Number 9870118A

Whirlpool COMPACTOR — COMPACTOR CARE diagram (page 11)
Fig. 33
5. Wash the inside of the cabinet with a clean sponge or soft cloth and a mild detergent in warm water. Rinse and dry thoroughly with a soft cloth.
6. To replace the drawer, grasp it by the sides and insert the rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
1. Wipe glass particles off of the ram cover with a cloth or paper towel. Throw the towel away.
Whirlpool COMPACTOR — COMPACTOR CARE diagram (page 11)
Fig. 34
2. Remove foods with a clean sponge or soft cloth and a mild detergent in warm water. Rinse and dry thoroughly with a soft cloth.

Cleaning Before a Vacation

If you will be away for more than a few days, remove the compactor bag. Remove the Key-knob and store it out of children’s reach.

Cleaning the Ram

Page 12 of the Whirlpool COMPACTOR user manual — TROUBLESHOOTING
Page 12 · click to enlarge
Page 12

TROUBLESHOOTING

Whirlpool COMPACTOR — TROUBLESHOOTING diagram (page 12)
Fig. 35

Try the solutions suggested here first in order to possibly avoid the cost of an unnecessary service call.

PROBLEMPOSSIBLE SOLUTION COMPACTOR WILL NOT OPERATECheck that the power supply cord is plugged into a grounded 3 prong outlet. Check the type of wall plug the compactor is plugged into. It is possible the compactor power cord is plugged into an outlet controlled by a wall switch. This can occur when the wall switch was meant for a garbage disposal outlet. A household fuse may have blown, or a circuit breaker tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Check that the drawer completely closed. Open the drawer to ensure the latch is locked. Close the drawer firmly and start the compactor. Check that the Key-knob is set to ON. See the “Starting Your Compactor” section. TRASH IS NOT COMPACTING Drawer must be more than half full before trash is compacted. The ram stops 7" (17.8 cm) from the bottom of the drawer. DRAWER WILL NOT OPENPush on the drawer front in an attempt to raise the ram. Be sure the latch is locked. Press ON, then press START. THERE IS NOT ENOUGH COMPACTION OR FORCEPress OFF halfway through the cyle. Press ON, then START to complete the cycle. BOTTLES DO NOT BREAKBottles will not break every time. Factors that affect bottle breakage: The thickness of the bottle’s glass and the content of the trash load below it may keep the bottle from breaking. COMPACTOR WILL NOT TURN OFFPush on the drawer front to attempt to engage the drawer monitor switch. Open drawer and be sure the latch is locked. Debris in the drawer area will cause the door to disengage from the drawer monitor switch, causing the compactor to keep running. This can also keep the compactor from starting. DRAWER IS HITTING THE CABINETThe cabinet opening should be 151/4"(38.7 cm) minimum with at least a 1/8" (3.2 mm) clearance on either side. Check that the compactor is centered in the cabinet opening. Check that the latch is locked. An unlatched drawer will cause the front door to be wobbly and offset from center. Check for debris on the drawer tracks or under the drawer. Debris may cause the drawer to lean to one side or not sit properly on the tracks. The compactor may be set too high or not level. The compactor can be raised or lowered with front leveling. COMPACTOR MOVING DURING OPERATIONCheck that the retaining brackets are installed to the cabinet. See the “Countertop Mounting” or “Cabinet-face Mounting” sections. DRAWER IS WOBBLY OR LOOSENOTE: By design, it is normal for the drawer to move slightly side to side. An unlatched door will wobble more than normal. Check that the door latch is in the locked position. The screws on the drawer front (door) may be loose. With a Phillips screwdriver, check to ensure the screws holding the door to the drawer are secure. COMPACTOR IS NOISYThe noise could be normal operation: The compactor is driven by a steel chain and steel sprockets.
Page 13 of the Whirlpool COMPACTOR user manual — NOTES
Page 13 · click to enlarge
Page 13

NOTES

Page 14 of the Whirlpool COMPACTOR user manual — NOTES
Page 14 · click to enlarge
Page 14

NOTES

Page 15 of the Whirlpool COMPACTOR user manual — ONE YEAR LIMITED WARRANTY WHAT IS COVERED WHAT IS NOT COVERED
Page 15 · click to enlarge
Page 15

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE. Please have the following information available when you call the Customer eXperience Center:

WHIRLPOOL ® MAJOR APPLIANCE LIMITED WARRANTY

  • Name, address, and telephone number
  • Model number and serial number
  • A clear, detailed description of the problem
  • Proof of purchase, including dealer or retailer name and address

IF YOU NEED SERVICE: 1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.whirlpool.com. 2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

ONE YEAR LIMITED WARRANTY WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased or, at its sole discretion, replace the product. In the event of product replacement, your appliance will be warranted for the remaining term of the original unit’s warranty period.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user, operator, or installation instructions. 2. In-home instruction on how to use your product. 3. Service to correct improper product maintenance or installation, installation not in accordance with electrical or plumbing codes, or correction of household electrical or plumbing (e.g., house wiring, fuses, or water inlet hoses). 4. Consumable parts (e.g., light bulbs, batteries, air or water filters, preservation solutions). 5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories. 6. Conversion of products from natural gas or propane gas. 7. Damage from accident, misuse, abuse, fire, floods, acts of God, or use with products not approved by Whirlpool. 8. Repairs to parts or systems to correct product damage or defects caused by unauthorized service, alteration, or modification of the appliance. 9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance finishes, unless such damage results from defects in materials and workmanship and is reported to Whirlpool within 30 days. 10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive environments including, but not limited to, high salt concentrations, high moisture or humidity, or exposure to chemicals. 11. Food or medicine loss due to product failure. 12. Pickup or delivery. This product is intended for in-home repair. 13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool servicer is not available. 14. Removal or reinstallation of inaccessible appliances or built-in fixtures (e.g., trim, decorative panels, flooring, cabinetry, islands, countertops, drywall) that interfere with servicing, removal, or replacement of the product. 15. Service or parts for appliances with original model/serial numbers removed, altered, or not easily determined. The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service must be provided by a Whirlpool designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

03/17

Page 16 of the Whirlpool COMPACTOR user manual — W11034804A
Page 16 · click to enlarge
Page 16

W11034804A

®/™ ©2018 Whirlpool. Used under licence in Canada. All rights reserved. 03/18

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
COMPACTOR WILL NOT OPERATECheck that the power supply cord is plugged into a grounded 3 prong outlet. Check the type of wall plug the compactor is plugged into. It is possible the compactor power cord is plugged into an outlet controlled by a wall switch. This can occur when the wall switch was meant for a garbage disposal outlet. A household fuse may have blown, or a circuit breaker tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Check that the drawer completely closed. Open the drawer to ensure the latch is locked. Close the drawer firmly and start the compactor. Check that the Key-knob is set to ON. See the “Starting Your Compactor” section. p.12
TRASH IS NOT COMPACTING Drawer must be more than half full before trash is compacted. The ram stops 7" (17.8 cm) from the bottom of the drawer. p.12
DRAWER WILL NOT OPENPush on the drawer front in an attempt to raise the ram. Be sure the latch is locked. Press ON, then press START. p.12
THERE IS NOT ENOUGH COMPACTION OR FORCEPress OFF halfway through the cyle. Press ON, then START to complete the cycle. p.12
BOTTLES DO NOT BREAKBottles will not break every time. Factors that affect bottle breakage: The thickness of the bottle’s glass and the content of the trash load below it may keep the bottle from breaking. p.12
COMPACTOR WILL NOT TURN OFFPush on the drawer front to attempt to engage the drawer monitor switch. Open drawer and be sure the latch is locked. Debris in the drawer area will cause the door to disengage from the drawer monitor switch, causing the compactor to keep running. This can also keep the compactor from starting. p.12
DRAWER IS HITTING THE CABINETThe cabinet opening should be 151/4"(38.7 cm) minimum with at least a 1/8" (3.2 mm) clearance on either side. Check that the compactor is centered in the cabinet opening. Check that the latch is locked. An unlatched drawer will cause the front door to be wobbly and offset from center. Check for debris on the drawer tracks or under the drawer. Debris may cause the drawer to lean to one side or not sit properly on the tracks. The compactor may be set too high or not level. The compactor can be raised or lowered with front leveling. p.12
COMPACTOR MOVING DURING OPERATIONCheck that the retaining brackets are installed to the cabinet. See the “Countertop Mounting” or “Cabinet-face Mounting” sections. p.12
DRAWER IS WOBBLY OR LOOSENOTE: By design, it is normal for the drawer to move slightly side to side. An unlatched door will wobble more than normal. Check that the door latch is in the locked position. The screws on the drawer front (door) may be loose. With a Phillips screwdriver, check to ensure the screws holding the door to the drawer are secure. p.12
COMPACTOR IS NOISYThe noise could be normal operation: The compactor is driven by a steel chain and steel sprockets. p.12

Ask about the Whirlpool COMPACTOR

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Whirlpool COMPACTOR

Be the first to ask — other owners or our team will answer.

Original document

Whirlpool COMPACTOR manual PDF

16 pages·748 KB·Household Appliance·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…