



Leveling the Build Plate 57
Emptying the Filament Waste Bin 59
Welcome. Let’s get started.

WELCOME.
Welcome to the User Manual for the MakerBot® Replicator® Z18 3D Printer. With the MakerBot Replicator Z18 you can print high-resolution, industrial-quality prototypes bigger than ever, but it also requires care and attention, so please be sure to read this manual all the way through.

The MakerBot® Replicator® Z18 3D Printer is covered by a limited warranty. For terms and conditions, see makerbot.com/legal
All information in this user manual (“Manual”) is subject to change at any time without notice and is provided for convenience purposes only. MakerBot Industries, LLC and our respective affiliates and suppliers (“MakerBot”) reserves the right to modify or revise this Manual in its sole discretion and at any time and makes no commitment to provide any such changes, updates, enhancements, or other additions to this Manual in a timely manner or at all. You agree to be bound by any modifications and/or revisions. Contact the MakerBot Support Team for up-to-date information.
In order to protect MakerBot proprietary and confidential information and/or trade secrets, this document may describe some aspects of MakerBot technology in generalized terms.
The design of this Manual and all text, graphics, information, content, and other material are protected by copyright and other laws. The contents are copyright 2009, 2010, 2011, 2012, 2013, 2014 MakerBot. All rights reserved. Certain trademarks, trade names, service marks, and logos (the “Marks”) used in this Manual are registered and unregistered trademarks, trade names, and service marks of MakerBot and its affiliates. Nothing contained in this Manual grants or should be construed as granting, by implication, estoppel, or otherwise, any license or right to use any Marks without the written permission of MakerBot. Any unauthorized use of any information, materials, or Marks may violate copyright laws, trademark laws, laws of privacy and publicity, and/or other laws and regulations.
WELCOME.

MakerBot does not warrant the accuracy or completeness of the information, products, or services provided by or through this Manual and assumes no assume no responsibility for any typographical, technical, or other inaccuracies in this Manual, which is provided “as is” and without any express or implied warranties of any kind, including warranties of merchantability, fitness for a particular purpose, or non-infringement of intellectual property. In connection with your use of this Manual, MakerBot shall not be liable to you for any damages whatsoever, be they direct, economic, commercial, special, consequential, incidental, exemplary, or indirect damages, even if MakerBot has been advised of the possibility of such damages, including without limitation, loss of business revenue or earnings, lost data, or lost profits. MakerBot assumes no responsibility, nor will be liable, for any damages to, or any viruses or malware that may infect, your computer, telecommunication equipment, or other property caused by or arising from your downloading of any information or materials related to this Manual. The foregoing exclusions do not apply to the extent prohibited by law; please refer to your local laws for any such prohibitions. MakerBot makes no warranties to those defined as “consumers” in the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act.
WELCOME.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington, D.C. 20402.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under FCC rules.
One MetroTech Center, 21st Floor
347.334.6800
MakerBot Industries, LLC · Brooklyn, NY 11201

Safety alert symbols precede each safety message in this manual. These symbols indicate potential safety hazards that could harm you or others or cause product or property damage.
There is a risk of shock. The MakerBot Replicator Z18 is not user serviceable. Warning:
Do not print using materials that have not been approved by MakerBot for use with the MakerBot Replicator Z18. Refer to the Specifications section on page 61 for more information.
There is a risk of shock. The MakerBot Replicator Z18 is not user serviceable.
The socket outlet must be located near the machine and must be easily accessible.
Children under 12 should be supervised by an adult.
melts plastic during printing. Plastic odors may be emitted during this operation. Make sure to set up the MakerBot Replicator Z18 in a well- ventilated area.
The MakerBot Replicator Z18
Z18
Z18
printer.
Dust generation and accumulation should be minimized. Some dust and dry powders can build static electricity charges when subjected to friction and create an ignition hazard.
•


The MakerBot Replicator Z18 makes solid, three-dimensional objects out of melted filament. First, use MakerBot Desktop to translate 3D design files into instructions for the MakerBot Replicator Z18. Then transfer those instructions to the MakerBot Replicator Z18 via USB drive, USB cable, ethernet, or Wi-Fi.
The MakerBot Replicator Z18 will melt filament and squeeze it out onto the build plate in thin lines to build your object layer by layer. With the huge build volume of the MakerBot Replicator Z18, this part of the process can take a long time. The method of 3D printing used by the MakerBot Replicator Z18 is called fused deposition modeling.





When you set up your MakerBot® Replicator® Z18 3D printer, remember that it was built and packaged very carefully at the MakerBot factory. We hope you’ll take your time and be just as careful unpacking it and getting it set up.

Inside your MakerBot Replicator Z18 you’ll find everything you need to get started, including a spool of MakerBot PLA filament and a sheet of build plate tape. To order more build plate tape or filament, go to store.makerbot.com

LARGE MAKERBOT PLA FILAMENT SPOOL

POWER CORD BUILD PLATE TAPE USB CABLE 5 MM HEX WRENCH


Cut the straps holding the MakerBot Replicator Z18 box in place and lift off the cardboard lid and sleeve.

Remove the tape and foam holding the door and filament drawer of the MakerBot Replicator Z18 open.
Peel the film off the outside of the MakerBot Replicator Z18.


Take the accessory and filament boxes out of the MakerBot Replicator Z18 and set them aside.

4 TAKE THE MAKERBOT REPLICATOR Z18 OFF OF THE PALLET
Lift the MakerBot Replicator Z18 off of the pallet and place it on a stable surface.
You will need to remove the lid of the MakerBot Replicator Z18 in order to load filament, so make sure the surface is low enough to allow you to access the top of your 3D printer.
alone. To prevent injury, lift with your legs,
not your back.


If the MakerBot Replicator Z18 shows any tendency to wobble, stabilize it using the adjustable leveling feet.
To adjust one of the feet, tilt the MakerBot Replicator Z18 up at one corner and rotate the foot to raise or lower that corner of your 3D printer.


Use a tool to unlock the lid of the MakerBot Replicator Z18. Pull the lid off and set it aside.


Remove the orange plastic clips from the top compartment of the MakerBot Replicator Z18. There are two clips, one on the belt at each side.


Locate and unwrap the Smart Extruder+ and press it against the back of the extruder carriage, with the connector pins facing the front of the MakerBot Replicator Z18. Magnets will lock the Smart Extruder+ into place.
again at any time, go to the control panel and
immediately after printing. Always allow the Smart Extruder+ to cool to 50° C completely
before removing it from the MakerBot Replicator Z18.

2a. Locate the Large MakerBot PLA Filament spool and remove it from its plastic bag.
2b. Push the right side of the filament drawer to open it.
2c. Place the spool in the drawer with the MakerBot logo facing up.


3a. Detach the free end of the filament from the spool and insert it into the hole at the back left corner of the filament drawer.
3b. Continue to feed the filament by hand into the slot at the side of the filament drawer. The filament will move up through the MakerBot Replicator Z18 to the top compartment. Stop feeding the filament when you see it emerge from the end of the filament guide tube.

4a. The build plate on the MakerBot Replicator Z18 has two parts: a removable plastic top plate, and a flat, sturdy aluminum base. Turn the latches on the front of the build platform and slide the top plate forward to release it. Then lift the top plate out of the MakerBot Replicator Z18.
4b. Peel the backing off of the sheet of build plate tape and lay the tape flat on the top plate, with the sticky side facing down.
4c. Smooth down the build plate tape so that it is stuck securely to all parts of the top plate.
4d. Fit the top plate onto the projections on the aluminum base and slide it back to snap it into place. Turn the build plate latches to secure the plate.

5a. Make sure the power switch is in the Off position.
5b. Locate the power cord and plug it into the power input port at the back of the MakerBot Replicator Z18.
5c. Plug the power cord into an electrical outlet.
located near the equipment and must
be easily accessible.
5d. Switch the power on and wait for the MakerBot Replicator Z18 to boot up. This will take several minutes.

The first time you turn on your MakerBot® Replicator® Z18 3D Printer, it will run a setup assistant that will introduce you to the control panel and walk you through everything you need to do to start your first print. Press the dial to begin the setup assistant.

The MakerBot Replicator Z18 is operated by means of a control panel at the lower right of the 3D printer. The control panel includes a color LCD screen, a rotary/push dial, and two buttons. See chapter 5 for more on the control panel and its menus.


Your MakerBot Replicator Z18 uses 1.75 mm diameter PLA filament to create 3D printed objects. Once your spool of MakerBot PLA Filament is loaded into the filament drawer and routed up to the top of the MakerBot Replicator Z18, all you have to do is load the free end of the spooled filament into the heated MakerBot Smart Extruder+.


Once you’ve loaded filament into your extruder, you’re ready to print something. The LCD panel will display the test prints we’ve loaded onto your MakerBot Replicator Z18 for you.
Replicator Z18 immediately after
completing a print. Always allow the
extruder to cool to 50° C before powering
down.
When your print is finished, you will need to remove it from the build surface.
Then lift the top plate out of the MakerBot Replicator Z18.

There are four ways to move files from your computer to your MakerBot Replicator Z18: Wi-Fi, Ethernet, USB cable and USB drive. Before you proceed, set up your computer to connect using one of these methods.
To connect via Ethernet: 1. Locate an Ethernet cable (not included).
To connect via USB cable: 1. Locate the included USB cable.
To connect via Wi-Fi: 1. Locate the included USB cable.
To transfer files via USB drive: No additional setup will be required. See Chapter 4 for instructions on exporting print files.

MakerBot® Desktop is a free app for preparing 3D prints and managing your 3D content. Whether you print directly to the MakerBot Replicator® Z18 3D Printer via USB cable, Wi-Fi or Ethernet, or you export your print files to a USB drive, MakerBot Desktop is where all your prints will begin.


You can connect to your MakerBot Replicator via USB cable, Ethernet or Wi-Fi at any time.
WI-FI 1. Connect the USB cable to your MakerBot Replicator Z18 and to your computer. MakerBot Desktop will automatically connect to your MakerBot Replicator Z18.
USB Connect the USB cable to your MakerBot Replicator Z18 and to your computer. MakerBot Desktop will automatically connect to your MakerBot Replicator Z18.

HOW IT WORKS MakerBot Desktop consists of four sections: Explore, Library, Prepare and Store.
Explore gives you access to Thingiverse and the hundreds of thousands of free 3D printable objects designed by the Thingiverse community. Use Explore to search Thingiverse for inspiration or new things to print, then save them to your collections or prepare them for printing.
Library gives you access to your MakerBot Cloud Library and helps you organize your 3D model files. Use it to store things you’ve collected on Thingiverse or bought from the MakerBot Digital Store as well as your own models.
Prepare is where you will turn 3D models into print files. Bring 3D models into the Prepare view to manipulate them on a virtual build plate. Then specify print options and send print files to your MakerBot Replicator Z18.
Store lets you buy print files for premium 3D models. When you buy a model in the MakerBot Digital Store, a print file for your MakerBot Replicator Z18 will be added to your MakerBot Cloud Library.
Learn provides video tutorials on common processes such as exporting files, preparing to print, and exploring Thingiverse. New tutorials will be added in future versions of MakerBot Desktop.
Use Store and Explore to find things to print, Library to keep them organized, and Prepare to send them to your MakerBot Replicator Z18 for printing.

Every 3D print starts with a 3D model. If you design a 3D model yourself, export it from your 3D modeling application in STL or OBJ format. If you don’t have a 3D model, download one from Thingiverse, either through the website at Thingiverse.com or through the Explore view in MakerBot Desktop.
DOWNLOADING AND PRINTING A MODEL FROM THINGIVERSE 1. Click Explore at the top of the MakerBot Desktop screen.

You should now see your model or models at the center of a gray rectangle. This is MakerBot Desktop’s representation of your 3D printer’s build plate. Let’s take a look at the other features visible in the Prepare view.

9 10 11 7



If you want to change any settings before printing, click Settings. This is where you can specify options that will affect the quality of your printed object, like print resolution and object strength.
To print with standard or previously specified settings, skip this step and go straight to printing.


If you would like to turn the heated build chamber on, use the advanced settings to create a custom profile. Go to mbot.co/15pwxXo to see the specific custom profile settings needed to turn the heated build chamber on.
When you are ready to print, click Print to slice the model using the current settings and send a .makerbot print file to your MakerBot Replicator Z18.

A feed of images from the onboard camera is always available when you’re connected to your MakerBot Replicator Z18. To view the feed, click the menu icon at the right side of the status bar to open the monitor panel. As long as you are connected to your MakerBot Replicator Z18 via USB or a local area network, the camera image will refresh every few seconds.
To take a photo, open the print monitor panel in MakerBot Desktop, mouse over the camera view, and click Take a Photo. MakerBot Desktop will take a photo and let you save it to your local computer.

The control panel on the MakerBot® Replicator® Z18 3D Printer allows you to interact with your 3D printer. You can use it to initiate prints, edit settings, and access information. This chapter describes the different things you can do with the control panel.

Use the control panel to:


Select the Print icon to initiate a print stored on a USB drive or internal storage or synced from your MakerBot Cloud Library.
Turn the dial to scroll through the list of available locations. Push the dial to select the location of the file you want to print.

Select USB Storage to print a file stored on a USB drive inserted into the USB port.
Select Internal Storage to print a file stored on the MakerBot Replicator Z18. The internal storage has a capacity of about 2 GB.
Select Your Library to print a sliced file from your MakerBot Cloud Library. In the Library menu:
Press the dial to select a location. Turn the dial to scroll through the list of available files and press it again to select one.



PRINTING During a print, you will be able to view print progress information as well as other details about your print.


If you are printing a file from Thingiverse, you will be prompted to share a photo. Photos shared to Thingiverse will appear on the Thing page in the I Made one! section. Sharing a photo is a nice thing to do – other Thingiverse users will love to see how your prints of their designs come out.
To share a photo, click Share to Thingiverse in MakerBot Desktop. The MakerBot Replicator Z18 will take a photograph of your build area and post the photo to the Thing page.
If you do not wish to share a photo of your print to Thingiverse, select Back to Menu.

Select the Filament icon to load or unload filament.
To load filament: 1. Use the dial to select Load filament.

When filament is loaded, insert the end of the filament guide tube unto the Smart Extruder’s loading tube and replace and lock the lid of the MakerBot Replicator Z18.
To unload filament: 1. Use the dial to select unload filament.
When filament is unloaded, begin the steps to load filament or replace and lock the lid of the MakerBot Replicator Z18.

To change filament spools: 1. Unload filament.
you do not, the filament could unravel or tangle on the spool.

Select the Preheat icon to preheat the Smart Extruderr. When you select Preheat, the extruder will immediately start heating. The current and target temperatures will be visible on the main screen.
Use the Utilities menu to access plate leveling, diagnostics and other tools.
Level Build Plate Select to begin the assisted leveling process. For best results when leveling, make sure filament is unloaded and the extruder nozzle is clean, and wipe any plastic debris off of the build plate.
Camera Select to access options related to your 3D printer’s built-in camera. In the camera menu, you can:

Additional options are available under System Tools.
Home Position Select to move the build platform and extruder assembly to their home positions. The build
platform will move all the way down and the extruder carriage will move to the front left
corner of the MakerBot Replicator Z18.
Attach Extruder Select for assistance in attaching the extruder.
Diagnostics Select to run a diagnostic sequence or to copy recent diagnostics logs to the USB drive.
System Logs Select to clear the log files for your MakerBot Replicator Z18 or to copy them to a USB drive.
Restore Factory Settings Select to return all settings on your MakerBot Replicator Z18 to the factory defaults.
Power Off Select to turn your MakerBot Replicator Z18 off. After you turn the MakerBot Replicator Z18 off
by selecting this option, you will be able to turn it back on by pushing the control panel dial.

Use the Settings menu to edit network and sharing settings and to personalize your MakerBot Replicator Z18.
Network Settings · MakerBot Account · Other Settings

Use the Info menu to view your 3D printer’s history and statistics.
Firmware View the version number of the firmware currently installed on your MakerBot Replicator Z18.
Statistics Select to view printing statistics, including total print time and the amount of space available in internal storage.
History Select to view recently printed items. Select an individual item from the list to view the date, print time, and quantity of filament used. Press the menu button to change the order of the listed items or to export the list to a CSV file that can be saved to a USB drive.

As you get to know your MakerBot® Replicator® Z18 3D Printer, you may run into issues with different parts of the printing process. Here is a handy guide to some simple-to-fix problems. For help with issues not covered in this chapter, go to makerbot. com/support.

Can’t load filament into the extruder.
Try unloading and loading again. Hold the extruder in place and try pushing the filament through. Push hard; as long as you are holding the extruder in place, pushing on the filament will not damage it.
Can’t remove filament from the extruder.
Try running the filament load script and allowing plastic to extrude for a few seconds. Then try unloading again.
Filament won’t extrude from the extruder.
Try unloading and reloading the filament. You may be able to avoid jams in the future by allowing the extruder to cool to 50° C before turning off your MakerBot Replicator Z18.
Printed object is stuck to the build plate.
Remove the plastic top plate from your MakerBot Replicator Z18 if you have not already done so. If you are still not able to remove your print from the build plate, try flexing the plastic plate slightly.

Make sure that the build plate tape is clean and securely applied to the build plate. If prints contin ue to peel off the plate, your plate may no longer be level. Follow the instructions on page 57 to level the build plate. You can also try printing with a raft. See page 38 for more on printing with a raft.
Object peels off the build plate during printing.
Touchscreen doesn’t respond. The control panel screen on the MakerBot Replicator Z18 is not a touchscreen. Turn the dial to scroll through the available options on the screen. Press the dial to select.
Can’t access the Library, Explore and Store sections of MakerBot Desktop.
You may not be logged into your MakerBot account. These features are only accessible when you are logged in. If you are logged into your MakerBot account but are still unable to access the Library, Store and Explore sections, your computer may not be connected to the internet.
The MakerBot Replicator Z18 is connected to a network, but MakerBot Desktop will only allow you to export, not print.
You may not have established a connection between MakerBot Desktop and your MakerBot Replicator Z18. In MakerBot Desktop, go to Devices > Connect to a New Device. Choose your MakerBot Replicator Z18 from the list of MakerBot 3D printers on your network and click Connect. When prompted, push the dial on your MakerBot Replicator Z18 to confirm the connection.

The extruder is installed, but the MakerBot Replicator Z18 does not recognize it.
Remove the extruder and run the extruder attachment script by going to Utilities > System Tools > Attach Extruder.
A print pauses unexpectedly. Make sure the front door of the MakerBot Replicator Z18 is closed.
When the door is opened during a print, the print will automatically pause. When the door is opened while a print is being initiated or during a preheat, the print or preheat will be cancelled.
To ensure that this does not happen, make sure the front door of the Replicator Z18 is securely closed before beginning a print or preheat.
If these solutions don’t solve your issue, or if you are having a problem that doesn’t appear here, please visit makerbot.com/support

The build plate on your MakerBot Replicator Z18 is leveled at the MakerBot Factory and locked into place, but over time it might shift slightly. If you observe that your prints are consistently peeling off of the build plate, you may need to level the plate again.
Before leveling your build plate, unload any filament, clear debris from the extruder nozzle and build plate, and allow the extruder to cool.



as directed by the instructions on the
control panel.

Firmware is the software that runs on your MakerBot Replicator Z18. Keeping your firmware up to date will help ensure that your MakerBot Replicator Z18 is in the best possible working order. Firmware updates allow MakerBot to add new features to your MakerBot Replicator Z18 and improve old ones.
MakerBot Desktop will let you know if there’s a firmware update available. To upgrade to the new version, just select Upload Firmware from the Devices menu. The software will walk you through the steps to bring your MakerBot Replicator Z18 up to date.
At the beginning of each print, your extruder will purge some plastic into a small container inside the MakerBot Replicator Z18. This filament waste bin is located in the back right corner of your MakerBot Replicator Z18, and is held in place by a magnet. When the filament waste bin is full, pull it free and empty it of its contents. Then return it to its place inside the MakerBot Replicator Z18.


100 microns [0.0039 in] 1.75 mm [0.069 in] MakerBot PLA Filament>2_s}wÖTÇá2fÇàyz2 X{~sÄwÅá>2additional materials such as bronzeFill, copperFill and woodFill (see MakerBot Labs) 0.4 mm [0.015 in] .makerboá
.stl, .obj, .thing Windows (7+), Mac OS X (10.7+), Linux (Ubuntu 12.04+, Fedora 19+)
49.3 W x 56.5 D x 86.1 H cm [19.4 W x 22.2 D x 33.9 H in] 65.0 x 71.9 x 106.0 cm [25.6 x 28.3 x 41.75 in] 41 kg [90 lbs] 52 kg [115 lbs]
TEMPERATURE Ambient Operating Temperature: 15-24°C [60-75.2°F] Storage Temperature: 0-38° C [32-100° F]
MECHANICAL Construction: Powder-coated steel with PC-ABS and aluminum composite material Build Surface: Injection molded PC-ABS Stepper Motors: 1.8° step angle with 1/16 microstepping XY Positioning Precision: 11 microns [0.0004 in] Z Positioning Precision: 2.5 microns [0.0001 in]
Fused deposition modeling

BACK BUTTON: The button at the top right corner of the control panel’s LCD screen. The back button will often allow you to return to a previous screen or cancel an action.
ETHERNET CABLE: A Cat5e cable used to connect your MakerBot Replicator Z18 to a local area network.
EXTRUDER ASSEMBLY: The extruder installed in the extruder carriage.
BUILD PLATE: The plate on which your MakerBot Replicator Z18 prints an object. The build plate on the MakerBot Replicator Z18 has two parts: a removable plastic top plate, and a flat, sturdy aluminum base. Additional plastic top plates are available for purchase at store.makerbot.com.
EXTRUDER CARRIAGE: The part of the extruder assembly that sits on the gantry and moves back and forth. When the extruder is installed in the extruder carriage, the extruder assembly is complete.
EXTRUDER NOZZLE: The opening on the end of the extruder from which heated filament emerges to be spread onto the build plate.
BUILD PLATE LATCHES: Two latches on the front of the build platform that hold the build plate in place. Rotate the latches before removing the build plate.
FILAMENT DRAWER: The part of your MakerBot Replicator Z18 that slides out to allow you to load a spool of filament.
BUILD PLATE TAPE: The heavy tape used as a build surface for your MakerBot Replicator Z18. Sheets of build plate tape for the MakerBot Replicator Z18 are available for purchase at store.makerbot.com.
FILAMENT GUIDE TUBE: The plastic tube that guides the filament from the filament spool to the extruder.
BUILD PLATFORM: The support for the build plate. The build platform includes knobs for manual leveling.
FILAMENT WASTE BIN: A clear plastic container in the back right corner of the MakerBot Replicator Z18. The extruder purges some plastic into the wipe bucket before prints and after filament changes.
CONTROL PANEL: The LCD screen, dial and buttons at the upper right corner of the MakerBot Replicator Z18. The control panel allows you to start prints, change settings and view status information.
FIRMWARE: The software that runs on your MakerBot Replicator Z18.
DIAL: The rotary/push dial on the control panel. Rotate the dial to scroll through available options and push the dial to select.

GANTRY: The apparatus that allows the extruder assembly to move around.
Desktop, and log on to Thingiverse and other MakerBot sites.
HEATED CHAMBER: The interior chamber of the MakerBot Replicator Z18. For information on heating the chamber during a print, go to mbot.co/15pwxXo
MAKERBOT CLOUD LIBRARY: The part of MakerBot Desktop where you can access your MakerBot Cloud Library and organize your own design files, files downloaded from or collected on Thingiverse™, or files purchased from the MakerBot Digital Store.
INTERNAL STORAGE: The part of the internal storage on your MakerBot Replicator Z18 that you can use to store print files. The capacity of the internal storage is about 2GB.
MAKERBOT DESKTOP: Free software for use with your MakerBot Replicator Z18. MakerBot Desktop will help you discover, manage, share and print 3D models.
LAYOUT: An arrangement of 3D models on the build plate. Multiple layouts can be saved as part of any Thing in your Library.
MAKERBOT DIGITAL STORE: A digital store where you can download premium 3D content.
LEVELING KNOBS: The three thumbscrews on the underside of the build platform that allow you to adjust the angle of the build plate. Only adjust the leveling knobs as instructed during the assisted leveling process.
MAKERBOT PLA FILAMENT: Polylactic acid filament. PLA is a corn-based thermoplastic. MakerBot PLA Filament is the source material from which you make objects on the MakerBot Replicator Z18.
LOCKING BOLTS: The four bolts that secure the aluminum base of the build plate to the build platform. Only loosen the locking bolts during assisted leveling.
MAKERBOT REPLICATOR Z18: The MakerBot® Replicator® Z18 3D Printer.
MENU BUTTON: The button at the bottom right corner of the control panel’s LCD screen. The menu button will often allow you to open a menu containing additional options.
.MAKERBOT: The format of print files for your MakerBot Replicator Z18. Print files contain instructions for your MakerBot Desktop 3D Printer.
.OBJ: A file format used for 3D models.

PROFILE: The settings used to slice your 3D model and create a print file. MakerBot Desktop Software comes with preset profiles for Low, Standard and High resolution prints.
SUPPORTS: Automatically generated support structures used to prop up any sections of a print that will not stand alone.
.THING: A file format used by MakerBot Desktop that stores additional information about your 3D model files.
RAFT: A plastic base printed on the build plate and used as a printing surface for your printed object.
THING: A file or group of files saved to Thingiverse or to your MakerBot Cloud Library.
SETTINGS DIALOG: The dialog that allows you to change which print settings will be used when you create a print file.
THINGIVERSE: MakerBot Thingiverse, an online community for sharing 3D design files.
SETUP ASSISTANT: The set of tasks that runs when you turn on the MakerBot Replicator Z18 for the first time. The setup assistant helps you level the build plate, load filament and start a test print. You can access the setup assistant at any time through the Utilities menu.
TOP COMPARTMENT: The top chamber of the MakerBot Replicator Z18. It contains the extruder carriage and is separated from the heated chamber by a bellows. The top compartment should always be kept locked when you are using the MakerBot Replicator Z18.
SLICING: The process of turning a 3D model into a print file containing instructions for your MakerBot 3D printer. The MakerBot Replicator Z18 uses print files with the extension .makerbot.
USB CABLE: A cable that allows your computer to communicate with the MakerBot Replicator Z18.
USB DRIVE: A USB flash drive. You can use a USB drive to transfer print files to and from the MakerBot Replicator Z18.
EXTRUDER: The extruder draws the filament from the spool, melts it, and pushes it through a nozzle onto the build plate.
Includes Smart Extruder+, Tough Smart Extruder+ and Experimental Extruder.
.STL: A widely used file format for 3D models.

Support makerbot.com/support Our website has extensive documentation and troubleshooting information about your MakerBot Replicator Z18. It’s a great resource when you want to try to solve issues quickly on your own.
makerbot.com/support/new/support At MakerBot, we take pride in offering expert, responsive, friendly customer support to customers around the world. If you need help resolving an issue with the MakerBot Replicator Z18, visit the web address above for an overview of your support options.
Sales sales@makerbot.com To learn about other MakerBot products,
including MakerBot Filament, please
email the address above, or call our Sales
Team at 347. 334. 6800.
Feedback thoughts@makerbot.com For general questions, or to tell us what’s on your mind, send an email to the address above. We love to hear from you, and using this email address helps keep our Sales and Support lines free for customers in need.


MakerBot One MetroTech Center, 21st Floor, Brooklyn, NY makerbot.com
Pages referenced in this manual — manufacturer, support and downloads.
What the fault codes shown on the display mean and how to clear them.
| Code | Meaning | Fix | |
|---|---|---|---|
| Z18 | This filament waste bin is located | p.59 |
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Can’t load filament into the extruder. | Try unloading and loading again. Hold the extruder in place and try pushing the filament through. Push hard; as long as you are holding the extruder in place, pushing on the filament will not damage it. | p.54 | |
| Can’t remove filament from the extruder. | Try running the fliament load script and allowing plastic to extrude for a few seconds. Then try unloading again. | p.54 | |
| Filament won’t extrude from the extruder. | Try unloading and reloading the fliament. You may be able to avoid jams in the future by allowing the extruder to cool to 50° C before turning off your MakerBot Replicator Z18. | p.54 | |
| Printed object is stuck to the build plate. | Remove the plastic top plate from your MakerBot Replicator Z18 if you have not already done so. If you are still not able to remove your print from the build plate, try fel xing the plastic plate slightly. | p.54 | |
| Object peels of fthe build plate during printing. | Make sure that the build plate tape is clean and securely applied to the build plate. If prints contin ue to peel of fthe plate, your plate may no longer be level. Follow the instructions on page 57 to level the build plate. You can also try printing with a raf.t See page 38 for more on printing with a raf.t | p.55 | |
| Touchscreen doesn’t respond. | The control panel screen on the MakerBot Replicator Z18 is not a touchscreen. Turn the dial to scroll through the available options on the screen. Press the dial to select. | p.55 | |
| Can’t access the Library, Explore and Store sections of MakerBot Desktop. | You may not be logged into your MakerBot account. These features are only accessible when you are logged in. If you are logged into your MakerBot account but are still unable to access the Library, Store and Explore sections, your computer may not be connected to the internet. | p.55 | |
| The MakerBot Replicator Z18 is connected to a network, but MakerBot Desktop will only allow you to export, not print. | You may not have established a connection between MakerBot Desktop and your MakerBot Replicator Z18. In MakerBot Desktop, go to Devices > Connect to a New Device. Choose your MakerBot Replicator Z18 from the list of MakerBot 3D printers on your network and click Connect. When prompted, push the dial on your MakerBot Replicator Z18 to confirm the connection. | p.55 | |
| The extruder is installed, but the MakerBot Replicator Z18 does not recognize it. | Remove the extruder and run the extruder attachment script by going to Utilities > System Tools > Attach Extruder. | p.56 | |
| A print pauses unexpectedly. | Make sure the front door of the MakerBot Replicator Z18 is closed. When the door is opened during a print, the print will automatically pause. When the door is opened while a print is being initiated or during a preheat, the print or preheat will be cancelled. To ensure that this does not happen, make sure the front door of the Replicator Z18 is securely closed before beginning a print or preheat. | p.56 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.