Instruction/ maintenance manual of the product 410 Broan
Go to page of 14
EC62 SERIES INTENDED FOR DOMESTIC COOKING ONL Y INST ALLER: LEA VE THIS MANU AL WITH HOMEO WNER. HOMEO WNER: USE AND CARE INFORMA TION ON P A GE 12. Broan-NuT one Canada Inc.; Mississauga, Ontario www .broan.ca 877-896-1119 www .broan.ca REGISTER Y OUR PRODUCT ON LINE A T : www .
W ARNING W ARNING - 2 - T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJUR Y TO PERSONS, OBSER VE THE FOLLO WING: 1. Use this unit only in the manner intended by the manuf acturer . If you hav e questions, contact the manuf acturer at the address or telephone number listed in the warranty .
HL0126 - 3 - - EC62 SERIES PO WER P A CK SYSTEM - 3¼” X 10” A DAPTER /D AMPER ( SUPPLIED WITH SINGLE BLOWER POWER P ACK ) S INGLE B LOWER (600 CFM , SUPPLIED WITH POWER P ACK ) D UAL B LOWER (100.
- 4 - 1. PREP ARE THE INST ALLA TION 2. INST ALL DUCTWORK AND ELECTRICAL WIRING Plan where and how the ductwork will be installed. Access to the top of the power pac k is preferred f or connection of ductwor k. Install proper-sized ductwork, elbows and roof or w all cap for the type of po wer pack y ou are installing.
NOTE: The dual blow er model has the same dimensions than the single blow er model, but does not hav e a hor izontal discharge . Ref er to single blow er power pack illustr ation for bac k and side views , and discard hor iz ontal discharge measurements.
- 6 - 4. INST ALL CUST OM HOOD LINER (OPTIONAL) The liners are specially designed to protect the e xter ior base of the custom hood. T o order , refer to the table belo w to find the r ight liner model n umber according to the width of the custom hood nominal width.
Using a Rober tson or a Phillips no . 2 screwdriver , remove both wiring cov er retaining screws ( A ). Detach it from the power pac k and set aside with its screws . Then, remov e both sides screws ( B ) retaining the front panel to the po wer pack. Carefully detach the front panel from the power pac k and set aside with its screws .
- 8 - 12. INST ALL THE ADAPTER AND THE DAMPER (DUAL BLOWER MODEL ONL Y) Using 2 no . 8 x 3/8’ ’ screws from par ts bag, assemble the adapter on the top of the po wer pack. Seal all joints with metal f oil duct tape to eliminate air leaks. Install 10” damper inside the VERTICAL ductw ork that will be attached to power pack.
- 9 - 14. INST ALL THE POWER P ACK Lift the power pac k in custom hood until the bottom of the clasping springs (2 per side) rests on the top of the custom hood base (gre y zone in illustration at right). F rom inside the power pac k, using provided no .
- 10 - 16. REINST ALL THE BLOWER (SINGLE BLOWER MODEL, HORIZONT AL DISCHARGE ONL Y) The single blo wer power pac k is factory shipped for a vertical discharge installation. F or a hor iz ontal discharge installation, the blo wer must be flipped. Using a 5/16” sock et, or a Phillips no.
19. REINST ALL FIL TERS 1. Using a Phillips no . 2 screwdriver , assemble the knob to each filter . NO TE: The screw MUST BE on filter tabs side . See illustration at r ight. CA UTION Remove pr otective plastic film covering filter s before installing them.
21. USE AND CARE P ower P ack Cleaning Stainless steel cleaning : Do: • Regularly wash with clean cloth or rag soak ed with warm water and mild soap or liquid dish detergent. • Alwa ys clean in the direction of original polish lines. • Alwa ys rinse well with clear water (2 or 3 times) after cleaning.
- 13 - 24. W ARRANTY 23. WIRING DIAGRAM K1 BLK BLACK BLU BLUE BRN BROWN GRY GREY ORG ORANGE RED RED WHT WHITE YEL YELLOW COLOR CODE LINE GROUND NEUTRAL 120 VAC WHT BLK YEL WHT YEL BLK YEL WHT J1 WHT J.
- 14 - 25. SERVICE P ARTS EC621306SS EC622301SS 1 1 HL0169 2 3 4 2 7 9 9 10 10 11 K EY NO . P ART NO . D ESCRIPTION Q TY . ( P OW ER P ACK M ODEL ) EC621306SS EC622301SS 1 SV13296 A DAPTER /D AMPER 3.
An important point after buying a device Broan 410 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Broan 410 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Broan 410 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Broan 410 you will learn all the available features of the product, as well as information on its operation. The information that you get Broan 410 will certainly help you make a decision on the purchase.
If you already are a holder of Broan 410, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Broan 410.
However, one of the most important roles played by the user manual is to help in solving problems with Broan 410. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Broan 410 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
