EN
Pulsar logo
Official user manual

Pulsar LT

16 pages·553 KB·Automotive·PDF·ENDEFRITNLJA
Pulsar LT
Table of Contents 27 sections Table of Contents · Safety Warning & Caution Read Me · WARNING · CAUTION · … ShowHide
Page 1 of the Pulsar LT user manual
Page 1 · click to enlarge
Page 1
Pulsar LT diagram (page 1)
Fig. 1
Pulsar LT diagram (page 1)
Fig. 2
Page 3 of the Pulsar LT user manual — WARNING: Prior to use, read the User Manual. Misuse of the
Page 3 · click to enlarge
Page 3

Safety Warning & Caution Read Me

Throughout this User Manual you will see important messages regarding your safety or the protection of your vehicle. These messages are designated by the words WARNING, CAUTION, or NOTICE.

WARNING

A WARNING indicates a hazardous situation which, if not avoided, will result in death or serious injury.

CAUTION

A CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

The product you have purchased is a high-performance product. As such, it does present some risks of which you should be fully aware. Do not use this product until you have carefully read the following safety information and the Owner Agreement.

WARNING: Prior to use, read the User Manual. Misuse of the

device could result in traffic accidents, death or serious injury, and/or

damage to your vehicle. POWERTEQ IS NOT RESPONSIBLE FOR AND

SHALL HAVE NO LIABILITY TO YOU FOR ANY CLAIMS ARISING OUT OF OR

RELATING TO ANY MISAPPLICATION OF THE DEVICE, CUSTOM TUNES,

IMPROPER USE OF CALIBRATIONS, MALFUNCTION OR LACK OF LEGAL

COMPLIANCE FOR CUSTOM PROGRAMS CREATED BY THIRD PARTIES.

Page 4 of the Pulsar LT user manual — Safety Guidelines
Page 4 · click to enlarge
Page 4

Safety Guidelines

WARNING

Before using device, read and understand the user manual, including

these additional safety instructions. Failure to do so could result in

DEATH or SERIOUS INJURY.

  • Do not exceed legal speed limits on public roadways. Violating traffic laws is dangerous and could result in injury or vehicle damage or both.
  • Use any enhanced speed capabilities of this product only in closed circuit, legally sanctioned racing environments expressly for this purpose. Violating traffic laws is dangerous and could result in injury or vehicle damage or both.
  • Do not operate the device while driving. Distracted driving could result in traffic accidents, death or serious injury, and/or damage to your vehicle.
  • Always perform all adjustments or changes while stopped. Changing a setting while driving can interfere with your attention to roadway conditions and could result in injury or vehicle damage or both.
  • Do not stack products. “Stacking” performance-enhancing devices or other improper installation can cause power train failure on the road. Other products may have features incompatible with your device. Follow all installation and operating instructions.
  • Some modifications may affect other parts of your vehicle. For example, if you remove/adjust the speed limiter in your vehicle, be sure your tires and other components are rated for the increased speeds they will have to withstand. Not doing so can lead to loss of vehicle control. Modify the speed limiter only for use in closed circuit, legally sanctioned racing environments, not for use on public roadways.

This product may meet the emissions compliance requirements of the California Air Resources Board and Federal Environment Protection Agency. If so, it is legal for sale and use on pollution-controlled vehicles operated on public streets and highways. The device must be installed and operated according to the instruction provided in this user manual. Included with these compliant products is a sticker for you to keep in your vehicle. You can either adhere it somewhere on the vehicle (e.g., the inside end of driver’s door) or simply store it in your glove box. The purpose of these stickers is to inform anyone who may have questions regarding the use of this product and how it affects emissions. For example, it would be something to show an emissions technician if questioned when taking your vehicle in for an emissions check to let him/her know the product is CARB emissions compliant.

Page 5 of the Pulsar LT user manual — Required Tools
Page 5 · click to enlarge
Page 5

Materials Installation L84 Pulsar LT

Pulsar LT — Materials Installation L84 Pulsar LT diagram (page 5)
Fig. 3 · Materials Installation L84 Pulsar LT
Pulsar LT — Materials Installation L84 Pulsar LT diagram (page 5)
Fig. 4 · Materials Installation L84 Pulsar LT
Pulsar LT — Materials Installation L84 Pulsar LT diagram (page 5)
Fig. 5 · Materials Installation L84 Pulsar LT

Required Tools

Small Flat Head Screwdriver 10mm Socket Socket Wrench Socket Extension

Show 5 more labels / short text on this page
Pulsar LT Module · Zip Ties · Velcro Strips · Mounting Bracket · Harness
Page 6 of the Pulsar LT user manual — Pulsar LT Installation
Page 6 · click to enlarge
Page 6

Pulsar LT Installation

1. Before installation, remove the negative side battery terminal.
2. Release red locking tab by pushing the red tab up as shown in the right.
Pulsar LT — Pulsar LT Installation diagram (page 6)
Fig. 6 · Pulsar LT Installation
Pulsar LT — Pulsar LT Installation diagram (page 6)
Fig. 7 · Pulsar LT Installation
Pulsar LT — Pulsar LT Installation diagram (page 6)
Fig. 8 · Pulsar LT Installation
3. Press the bottom right tab on the connector inward to release. Then the connector can slide upwards toward the red tab to take it apart as shown above.
4. Release the locking tab in the back of the connector with a pick or small flathead screw driver as shown below.
Pulsar LT — Pulsar LT Installation diagram (page 6)
Fig. 9 · Pulsar LT Installation
Page 7 of the Pulsar LT user manual — Pulsar LT Installation Cont’d
Page 7 · click to enlarge
Page 7

Pulsar LT Installation Cont’d

Pulsar LT — Pulsar LT Installation Cont’d diagram (page 7)
Fig. 10 · Pulsar LT Installation Cont’d
5. Remove the zip tie tree from the bracket as seen to the right.
6. Locate and remove the factory nut holding down the front of the air intake as seen in picture with a 10 mm socket.
7. Install the supplied bracket as shown in picture. Reinstall the factory nut and tighten by hand.
Pulsar LT — Pulsar LT Installation Cont’d diagram (page 7)
Fig. 11 · Pulsar LT Installation Cont’d
8. Install the supplied Pulsar LT harness and rotate the bracket so that the wires going through the frame are not rubbing. Then tighten the factory nut.
Pulsar LT — Pulsar LT Installation Cont’d diagram (page 7)
Fig. 12 · Pulsar LT Installation Cont’d
9. Install the harness onto the factory mounting tab and then route the harness.
Pulsar LT — Pulsar LT Installation Cont’d diagram (page 7)
Fig. 13 · Pulsar LT Installation Cont’d
10. Install the module and Velcro to the top of the air box. It is a good idea to clean the back of the module and the top of the air box with an alcohol wipe before installing the Velcro.
11. Reinstall the negative side battery terminal.
Page 8 of the Pulsar LT user manual — TPMS
Page 8 · click to enlarge
Page 8

Programmable Features

Programming Menu

The vehicle has to be running to turn off cruise control.

Access the Programming Menu

Seven modes can be accessed through the programming menu. The speedometer (MPH) gauge is used to display the modes and programming inputs. The cruise control switches will be used to navigate the programming menu.

10. Speed Limiter Adjustment (82-140 MPH) 20 - TPMS Adjustment (1-99 PSI) 30 - Tire Size Correction (Input stock then modified sizes for front and rear tires) 40 - Axle Ratio (Input stock then modified axle ratio) 50 - Clear DTC’s 60 - Auto Start/Stop Disable 70 - DFM Disable (Will also disable Auto Start/ Stop)

TPMS

1. The vehicle must be turned off.
2. Without putting your foot on the brake pedal hold the Start Engine button until the truck gauges turn on and green light is seen on the start button. (approx. 5 seconds)
3. Adjust the vehicles screen cluster to the digital speedometer
4. Hold the cancel cruise control button until the speedometer sweeps to 140. (Approx. 5 seconds)
5. Use the +RES or –SET wheel to navigate to the desired programming mode.
6. Press the cancel cruise control button to select the mode.

STEP 7 -The speedometer gauge will sweep and then stop at the current programmed condition. (The stock input will be displayed if not previously adjusted.)

Show 6 more labels / short text on this page
DFM Disable · Auto Start/Stop · Clear DTC’s · Axle Ratio · Tire Size · Speed Limiter
Page 9 of the Pulsar LT user manual — Tire Size
Page 9 · click to enlarge
Page 9

Speed Limiter

After accessing speed limiter programming mode, adjustment between 82 and 140 MPH can be input.

1. Access the Programming Menu.
2. Using +RES or -SET, select mode 10 (MPH).
3. Use +RES or -SET wheel to adjust to the desired value.
4. Press the cancel cruise control button to save the input value.
5. The speedometer will sweep to 140 MPH indicating the function is complete.

TPMS - Tire Pressure Monitor System

After adjusting the TPMS inflate to number, the min amd max values

automatically adjust. This mode reprograms the vehicle ECM.

1. Access the Programming Menu.
2. Using +RES or -SET, select mode 20 (MPH)
3. Use the +RES or –SET wheel to adjust to the desired value between 25 and 99 (PSI).
4. Press cancel cruise to select.
5. Speedometer sweeps to 140 MPH for 3 seconds indicating TPMS has been selected.

Tire Size

Input Stock and Modified Tire Size.

1. Access the Programming Menu.
2. Using +RES or -SET, select mode 30 (MPH)
Page 10 of the Pulsar LT user manual — Axle Ratio
Page 10 · click to enlarge
Page 10

Tire Size Cont’d

3. Enter Stock Tire Size Example: 33.5” TireWhole Number = 35, Decimal = 5 a. Using +RES or -SET, adjust to the Stock Tire Whole number. b. Press cancel cruise to save the input. c. Using +RES or -SET, adjust the Stock Tire Decimal number. d. Press cancel cruise to save the input.
4. Enter Modified Tire Size a. Using the +RES or -SET wheel to adjust to the Modified Tire Whole number. b. Press cancel cruise to save the input. c. Use the +RES or -SET wheel to adjust the Modified Tire Decimal number. d. Press cancel cruise to save the input.
5. The speedometer will sweep to140 MPH, indicating the function is complete.

Axle Ratio

Input Stock and Modified Axle Ratio.

1. Access the Programming Menu.
2. Using the +RES or -SET, select mode 40 (MPH)
3. Press cancel cruise to select.
4. Enter Stock Axle Ratio. Example: 3.73 AxleWhole Number = 3, Decimal = 73 a. Using +RES or -SET, adjust to the Stock Axle Whole number. b. Press cancel cruise to save the input. c. Using +RES or -SET, adjust the Stock Axle Decimal number. d. Press cancel cruise to save the input.
5. Enter Modifed Axle Ratio. a. Using +RES or -SET, adjust to the Modified Axle Whole number. b. Press cancel cruise to save the input. c. Using +RES or -SET, adjust the Modified Axle Decimal number. d. Press cancel cruise to save the input.
Page 11 of the Pulsar LT user manual — DFM (Dynamic Fuel Management) Disable
Page 11 · click to enlarge
Page 11

Axle Ratio Cont’d

6. The speedometer will sweep to 140 MPH, indicating the function is complete.

Clear DTC’s

1. Access the programming menu.
2. Using +RES or -SET, select mode 50 (MPH)
3. Press cancel cruise to select.
4. The speedometer will sweep to 140 MPH, indicating the function is complete.

Auto Start/Stop Disable

1. Access the Programming Menu.
2. Using +RES or -SET, select mode 60 (MPH)
3. Use the +RES or –SET wheel to adjust to the desired value. a. 0 = Auto Start/Stop is active b. 10 = Auto Start/Stop is disabled
4. Press the cancel cruise control button to save the input value.

STEP 5 -The speedometer will sweep 0 to 140 MPH indicating the function is complete.

DFM (Dynamic Fuel Management) Disable

Disabling DFM will automatically disable Auto Start/Stop

1. Access the programming menu.
2. Using +RES or -SET, select mode 70 (MPH)
3. 3. Use the +RES or –SET wheel to adjust to the desired value. a.0 = DFM is active b.10 = DFM is disabled
4. Press the cancel cruise control button to save the input value.
5. The speedometer will sweep 0 to 140 MPH indicating the function is complete.
Page 12 of the Pulsar LT user manual — Responsiveness Level Adjustment
Page 12 · click to enlarge
Page 12

Responsiveness Level Adjustment

When the vehicle is running and cruise control is turned off, the vehicle throttle responsiveness can be adjusted. The responsiveness level is indicated using the vehicle’s speedometer. STEP 1 - Using the +RES or -SET, adjust to the desired value.

Level 0 = Stock Level 1 = Reduced responsiveness (up to 15% less than stock) Level 2 = Increased responsiveness (up to 15% over stock) Level 3 = Increased responsiveness (up to 30% over stock) Level 4 = Increased responsiveness (up to 48% over stock) Level 5 = Increased responsiveness (up to 65% over stock)

2. To recall the vehicle’s performance level, press the cancel cruise control button.
Page 13 of the Pulsar LT user manual — Downloading Update Agent 1.0 (Optional) Update Software
Page 13 · click to enlarge
Page 13

Downloading Update Agent 1.0 (Optional) Update Software

The Update Agent may be used to update the device via the USB connection. The software can be downloaded through the internet. This process currently can only be done on a Windows computer, Mac devices are not supported.

1. Go to a computer with internet access, and go to one of the following websites: superchips.com - diablosport.com - edgeproducts.com
2. Go to the website’s Updates/Downloads tab and click the link “Download Update Agent 1.0” and save the .exe file to a findable location on the computer.
3. Run the .exe installation program that you downloaded, and read through the license terms and conditions, check the agreement box and click Install. Continue through installation until it says Installation Successfully Completed. Click Close to finish the process.
Pulsar LT — Downloading Update Agent 1.0 (Optional) Update Software diagram (page 13)
Fig. 14 · Downloading Update Agent 1.0 (Optional) Update Softw…
Pulsar LT — Downloading Update Agent 1.0 (Optional) Update Software diagram (page 13)
Fig. 15 · Downloading Update Agent 1.0 (Optional) Update Softw…
Pulsar LT — Downloading Update Agent 1.0 (Optional) Update Software diagram (page 13)
Fig. 16 · Downloading Update Agent 1.0 (Optional) Update Softw…
Page 14 of the Pulsar LT user manual — Product Updates (Optional)
Page 14 · click to enlarge
Page 14

Product Updates (Optional)

This device has the ability to update via a USB connection. A USB to OBDII update cable is required to perform the update. The cable is sold separately. It is recommended that a battery charger is attached and turned on during the update process.

1. Take computer with Update Agent 1.0 installed to the location of the vehicle with the Pulsar device.
2. Turn the vehicle’s ignition to the RUN position (do not start the engine) then open Update Agent 1.0 on the computer, plug in USB to OBDII cable into both the vehicle’s OBDII port and a USB port on the computer.
3. Update Agent 1.0 should automatically detect the Pulsar LT device, follow onscreen instructions until it checks for an update. If an update is available, click yes.
4. Follow update steps as is shown onscreen. Do not power down the vehicle during the entire process unless prompted by the Update Agent. Once Update Agent 1.0 says “Your device is up-to-date,” click ok and disconnect the USB to OBDII cable.
Pulsar LT — Product Updates (Optional) diagram (page 14)
Fig. 17 · Product Updates (Optional)
OBDII Port NOTEOBDII Port location may vary depending on vehicle
Page 15 of the Pulsar LT user manual — Frequently Asked Questions FAQs
Page 15 · click to enlarge
Page 15

Frequently Asked Questions FAQs

Question: Can I adjust power levels when cruise control is on? Answer: No, only when cruise control is off. NOTE: Cruise control can be used as normal, you just can’t change power levels when cruise control is on.

Question: Should I remove the Pulsar LT prior to going to the dealer? Answer: Yes, please remove the Pulsar LT as to eliminate it from the system so they can perform any updates or services.

Question: How do I check what level I am on when cruise control is off? Answer: Simply press Cancel on power steering keypad.

Question: Can I “stack” or use other tuners with this device? Answer: No, please do not use any other tuners when the Pulsar LT is in use or installed. Stacking tuners with the Pulsar LT may cause serious damage to the vehicle.

Question: What is the best way to accurately measure tire size? Answer: Mark a line on the ground where the center of the tire rests, then drive the vehicle for two full rotations of the tire and mark the spot where it comes to a rest with another line. Measure the length between the two lines and divide by two. Then divide that number by Pi π (3.14159265359).

Page 16 of the Pulsar LT user manual — Frequently Asked Questions FAQs
Page 16 · click to enlarge
Page 16

Copyright© 2020 D10024100 Rev01 05/11/2021 For additional questions not found in the user guide call: Powerteq Technical Support: (801)-476-3343 6:00 am - 5:00 pm MST

To expedite your support call, please have your Vehicle Information, Part Number, and Serial Number ready prior to calling Technical Support.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Pulsar LT

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Pulsar LT

Be the first to ask — other owners or our team will answer.

Original document

Pulsar LT manual PDF

16 pages·553 KB·Automotive·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…