EN
Ampeg logo
Official user manual

Ampeg Bass Amplifier (MICRO-CL Stack)

8 pages·342 KB·Bass Amplifier·PDF·ENDEFRITNLJA
Ampeg Bass Amplifier (MICRO-CL Stack)
Table of Contents 14 sections Owner’s Manual · TABLE OF CONTENTS · What’s in the Box · Introduction · … ShowHide
Page 1 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — Owner’s Manual
Page 1 · click to enlarge
Page 1
Ampeg Bass Amplifier (MICRO-CL Stack) — Owner’s Manual diagram (page 1)
Fig. 1 · Owner’s Manual

Owner’s Manual

Page 3 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — Features
Page 3 · click to enlarge
Page 3

Features

Amplifier:

  • Power output: 100 Watts at 8 Ω
  • Preamp: Solid-state
  • Power Amp: Solid-state
  • Tone Controls: Bass, Mid, Treble
  • Unbalanced Line Out
  • Effects Loop
  • Dual Inputs (0 dB and –15 dB)
  • 1/8" Headphone Out / Line In
  • Dimensions (H x W x D): 7" x 12.2" x 10"
  • Handling Weight: 13.8 lb / 6.3 kg

Speaker Cabinet:

  • 100 Watts Power Handling at 8 Ω
  • 2 x 10" LF Drivers
  • Frequency Response: 57 Hz – 5 kHz
  • Sensitivity: 100 dB SPL @ 1W/1m
  • Dimensions (H x W x D): 13" x 24" x 11"
  • Handling Weight: 33.2 lb / 15.1 kg
Page 4 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — The Front Panel
Page 4 · click to enlarge
Page 4

The Front Panel

Ampeg Bass Amplifier (MICRO-CL Stack) — The Front Panel diagram (page 4)
Fig. 2 · The Front Panel

1 2 3 4 5 6 7 8 9 10 11

1. 0 dB INPUT: The signal output from a passive instrument may be connected to this 1/4" Input by means of a shielded instrument cable.
7. AUX LEVEL: Use to control the output level of the signal fed to the Aux Input [8]. Use it wisely and turn it down when making connections, putting on headphones, or trying something new.
2. –15 dB INPUT: The signal output from an active instrument may be connected to this 1/4" input by means of a shielded instrument cable.
8. AUX INPUT: The audio output from line level sources such as a mobile device or MP3 player, can connect to this 1/8" TRS stereo input. The incoming audio is mixed with the preamp signals, so you can play along to a practice track while listening with headphones. (The audio here appears in the cabinet speakers until headphones are plugged in; then heard in the headphones only).
3. MASTER: Use to control the output level of the instrument only. It affects the Speaker Output [13] and Headphones Output [9]. Use it wisely and turn it down when making connections, putting on headphones, or trying something new.
4. TREBLE: Use to adjust the high frequency level of the amplifier. This provides up to 13 dB of boost, or 13 dB of cut, at 6 kHz. The high frequency output is flat at the center position.
9. PHONES: Use this 1/8" TRS stereo output to connect headphones. The output here is a mix of the line level signals reaching the amplifier, plus any incoming audio from the Aux In jack [8].

Before putting on headphones, make sure the Master control [3] and Aux Level [7] are turned down. This will reduce the chance of hearing damage due to loud volumes.

5. MID: Use to adjust the midrange frequency level of the amplifier. This provides up to 11 dB of boost, or 11 dB of cut, at 600 Hz. The midrange frequency output is flat at the center position. Rotate the control counterclockwise for a “contoured” sound (more distant, less midrange output) or clockwise for a sound that really cuts through.
10. ON LED: This LED illuminates red when the power is on.
11. POWER SWITCH: Use this switch to turn the overall system power on or off. Press the top of the switch to turn on the power, and press the bottom of the switch to turn it off.
6. BASS: Use to adjust the low frequency level of the amplifier. This provides up to 11 dB of boost, or 11 dB of cut, at 50 Hz. The low frequency output is flat at the center position.
Page 5 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — Rear Panel Connector Plate
Page 5 · click to enlarge
Page 5

The Rear Panel

Ampeg Bass Amplifier (MICRO-CL Stack) — The Rear Panel diagram (page 5)
Fig. 3 · The Rear Panel
POWER SOURCE120V 60Hz PRIMARY FUSE: T3AL /250V POWER CONSUMPTION: 85W

12 13 14 15 16

12. AC POWER INPUT: The amplifier is equipped with a detachable power cable that plugs into this IEC Mains socket on the back of the amplifier. The AC power cord should only be plugged into a grounded power outlet that meets all applicable electrical codes and is compatible with the voltage, power, and frequency requirements stated on the rear panel of the amplifier.
16. UNBALANCED LINE OUT JACK: Typically, you would connect this Output to the balanced input of an external mixer or a recorder. In this way, you do not have to mic the speaker cabinet in order to add it to the main mix or to record. This output is affected by the Master control [3].

This output can connect to external power amplifiers, or powered loudspeakers, as long as they have their own input controls to adjust the volume level.

Do not attempt to defeat the safety ground connection.

13. SPEAKER OUTPUT JACK: This 1/4" TS Output jack supplies speaker-level power to the Speaker Cabinet Input [17]. The rated power output is 100 Watts into 8 Ω.

Rear Panel Connector Plate

Ampeg Bass Amplifier (MICRO-CL Stack) — Rear Panel Connector Plate diagram (page 5)
Fig. 4 · Rear Panel Connector Plate

Use a (non-shielded) speaker cable with 1/4" TS ends to make the connections. Do not use (shielded) instrument cables as they may overheat.

14. EFFECTS LOOP RETURN JACK: Use this 1/4" TS unbalanced input to return the processed, line level output of an external effects processor (for example). The processor could be fed by signals from the Effects Loop Send [15].
17. 1/4" TS INPUT JACK: Connect the speaker-level output [13] to this speaker input jack using a (non-shielded) speaker cable.

Always use a (non-shielded) speaker cable—never use a (shielded) instrument cable to connect speakers to an amplifier.

15. EFFECTS LOOP SEND JACK: Use this 1/4" TS unbalanced output to send a line level output to an external effects processor (for example). The output here is affected by all controls, including the Master [3].

Use the Effects Loop Return jack [14] to feed the returned processed signals back into the power amplifier.

Page 6 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — LINE OUT
Page 6 · click to enlarge
Page 6

System Block Diagrams

Amplifier:

Ampeg Bass Amplifier (MICRO-CL Stack) — System Block Diagrams diagram (page 6)
Fig. 5 · System Block Diagrams

LINE OUT

EFFECTS LOOP

SPEAKER OUTPUT

Speaker Cabinet:

Ampeg Bass Amplifier (MICRO-CL Stack) — LINE OUT diagram (page 6)
Fig. 6
Show 7 more labels / short text on this page
Inputs · 0 dB · Send · -15 dB · Return · AUX Inputs · Phones
Page 7 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — Technical Specifications
Page 7 · click to enlarge
Page 7

Technical Specifications

Output Power Rating 100 Watts @ 8 Ω

Signal to Noise Ratio 72 dB (20 Hz – 20 kHz, unweighted)

Maximum Gain 59 dB at 1 kHz

Amplifier Inputs 2 x 1/4" Jacks [0dB, –15dB] 2 x 1/8" Jacks [Aux, Headphones]

Tone Controls Bass: +11/–11 dB @ 50 Hz Midrange: +11/–11 dB @ 600 Hz Treble: +13/–13 dB @ 6 kHz

Power Requirements Japan100V ~50–60 Hz, 85W U.S.: 120V ~60 Hz, 85W EU: 220–240V ~50–60 Hz, 85W

Amplifier Size (H x W x D) 7 in/178 mm (with feet) x 12.2 in/310 mm x 10 in/254 mm

Amplifier Weight 13.8 lb / 6.3 kg

Cabinet Frequency Response 57 Hz – 5 kHz

Cabinet Sensitivity 100 dB SPL @ 1W/1m

Cabinet Input 1 x 1/4" Jack

Speaker Specs 2 x 10" LF drivers

Cabinet Size (H x W x D) 13 in/330 mm (with feet) x 24 in/610 mm x 11 in/279 mm

Cabinet Weight 33.2 lb / 15.1 kg

The MICRO-CL is covered with a durable, fabric-backed vinyl material. Clean with a dry, lint-free cloth. Never spray cleaning agents onto the stack. Avoid abrasive cleansers which would damage the finish.

Ampeg continually develops new products and improves upon existing ones. For this reason, the specifications and information in this manual are subject to change without notice.

Page 8 of the Ampeg Bass Amplifier (MICRO-CL Stack) user manual — Warranty and Support
Page 8 · click to enlarge
Page 8

Warranty and Support

Visit WWW.AMPEG.COM to...

(1) ...identify WARRANTY coverage provided in your local market. Please keep your sales receipt in a safe place.

(2) ...REGISTER your product.

(3) ...CONTACT Technical Support, or call 818-575-3600.

www.ampeg.com Yamaha Guitar Group, Inc. 26580 Agoura Road, Calabasas, CA 91302-1921 USA Rev. B

© 2021 Yamaha Guitar Group, Inc. All rights reserved. Ampeg, the Ampeg logo, and SVT are trademarks or registered trademarks of Yamaha Guitar Group, Inc. in the U.S. and/or other jurisdictions.

Serial Number_______________________________
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Ampeg Bass Amplifier (MICRO-CL Stack)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Ampeg Bass Amplifier (MICRO-CL Stack)

Be the first to ask — other owners or our team will answer.

Original document

Ampeg Bass Amplifier (MICRO-CL Stack) manual PDF

8 pages·342 KB·Bass Amplifier·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…