Instruction/ maintenance manual of the product 70 Britax
Go to page of 70
Boulevard TM 70 User Guide IMPORT ANT : Thoroughly read and follow all instructions before installing this child seat. Store this user guide in the pocket behind the cover (See features pages for reference).
.
©2010 Britax Child Safety , Inc. All rights reserved. Printed in USA P435100_R1:09.10 This product and its components are subject to change without notice. Safety Information ...........................................................................
2 Section Title • Use only in a rear -facing position when using it with an infant weighing less than 20 lbs (9.1 kg) OR is less than 1 year of age. • Use only with children who weigh between 5 and 70 lbs (2.3 – 31.8 kg) and whose height is 49 in.
3 Section Title • This child seat must not be used in the home, in boats, or other non-certified applications. • Based on crash statistics, the National Highway T raffic Safety Administration (NHTSA) recommends that parents select the back seat as the safest location for a properly installed child seat.
4 Impor tant Notes • V erify that the child seat is securely installed and the harness is properly adjusted around the child each time the child seat is used . • Discontinue use of this child seat if it has been in a moderate or severe crash. It is not necessary to replace a car seat after a minor cra sh de fine d by t he U.
5 Cer tification This child restraint system conforms to all applicable Federal Motor V ehicle Safety Standards. This Restraint is Certified For Use in Motor V ehicles and Aircraft. Registration Child restraints could be recalled for safety reasons. Y ou must register this restraint to be reached in a recall.
6 Impor tant Child Seat Usage Information All infants must ride rear-facing at least until they have reached 1 year of age and weigh 20 lbs (9.1 kg). An infant positioning insert may be necessary for small infants to achieve a snug fit if the child is under 12 lbs and the lowest harness slots fall above the infants shoulders.
7 WARNING! FORWARD-FACING use of this child seat is ONL Y for children who meet ALL of the requirements below . If the child cannot be secured within these requirements because they are too large, another type of child seat (such as a booster) may be required.
8 Compatible V ehicle Seat Belts NOTE: The information in this section only applies to installation with vehicle seat belts. V ehicle seats and seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s manual for specific information about your vehicle seat belts and their use with child seats.
9 2. ELR (Emergency Locking Retractor) with Locking Latch Plate a Has a latch plate that locks the vehicle belt. * This type of latch plate locks the vehicle belt when the vehicle belt and latch plate lie flat.
10 4. ELR (Emergency Locking Retractor) with a Sliding Latch Plate a Has a latch plate that freely slides along the vehicle seat belt webbing. b Has a retractor that locks only in an emergency situation such as sudden stop or crash.
11 c Tightens by feeding the belt webbing back into the retractor . 6. Locking Latch Plate a Has a latch plate that prevents the webbing from becoming loose.
12 Incompatible Vehicle Seat Belts WARNING! The following types of vehicle seat belts are NOT compatible with this child seat. If any of the belt types listed below are in the chosen seating position, choose another vehicle seating position or check your vehicle owner’s manual for information on installing a car seat in your vehicle.
13 WARNING! DO NOT place child seat rear -facing in the front seat of a vehicle with a passenger air bag unless deactivated. DEA TH or SERIOUS INJURY can occur . See your vehicle owner’s manual for child seat installation instructions. The back seat is the safest place for children 12 and under .
14 1 Cover 2 Harness Height Adjuster 3 Head Restraint 4 Comfort Pads 5 Infant Body Pillow 6 Harness Holder 7 Lower Connector Bar 8 Lower Connector Strap (LA TCH component) 9 Lower Connector Adjuster R.
15 17 Belly Pad 18 Harness Adjuster Lever (under cover) 19 Harness Adjuster Strap 20 Recline Adjustment Handle 21 Shell 22 Serial Number & Manufactured Date Label 23 Harness Slots 24 Forward-Facin.
16 Harness Height Adjustment 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Squeeze the harness height adjuster , slide the harness into the desired position and release. * Ensure the harness has locked into position.
17 Adjusting Buckle P osition 1 Unbuckle the harness. Remove the belly pad and push the buckle through the cover . 2 T urn the buckle webbing and slide it between buckle positions. 3 Slide the buckle retainer into the buckle slot, and ensure the red release button faces out.
18 F astening the Buckle Insert one tongue at a time into the buckle. NOTE: Proper connection is confirmed with a click after inserting each buckle tongue. Releasing the Buckle Press the release button and pull the tongues from the buckle. NOTE: Periodically clean the buckle to ensure proper operation.
19 Using the Lock- Offs IMPORT ANT : Both parts of the lock -off must be opened to secure a vehicle belt. 1 Open the locking tab 2 Open the clamp T o Open: 1 Close the clamp over the vehicle belt 2 Sl.
20 Recline P ositions This child seat has 3 positions. T o adjust, pull the recline handle then rotate the child seat shell into the desired position. Release the recline handle, then verify the child seat has locked into position. NOTE: Set the recline position BEFORE installing.
21 Forward-F acing IMPORT ANT : In forward-facing installations, it is important that the base of the child seat rests completely flat on the vehicle seat. As illustrated below , it is permissible to allow up to 20% or 3 inches (7.6 cm) of the base to hang over the edge of the vehicle seat.
22 Using Lower Anchors and T ethers for Children (L A TCH) Lower Anchors and T ethers for Children or LA TCH, is a system available on this child seat that offers an alternative to vehicle seat belt installation methods. See pages 14 and 15 for LA TCH components on this child seat.
23 Using the Lower Connectors Where to find the Lower Connectors The lower connectors are located in the back of the base of the child seat. Store the connectors in the slots when not in use. T o remove the lower connector from the storage slot or lower anchor: 1 Press and hold the red release button.
24 Using the V ersa- T ether ® T ether anchor locations vary from vehicle to vehicle. Check your vehicle owner’s manual and look for the tether anchor symbol shown in the diagram to help identify where the top tether anchor points are located in your vehicle.
25 Rear-F acing T ether Connector Strap Because every vehicle model is different, a location to anchor the tether for rear -facing installations may vary . Use the rear -facing tether connector strap to assist in creating an anchor point. 1 Find a fixed location in the vehicle that is bolted to the floor .
26 IMPORT ANT : The Versa- T ether ® carry clip is only for use when you wish to carry the child seat between locations. Do not install the child seat with the V ersa- T ether attached to the carry clip. Secure the excess Versa- T ether webbing in the elastic strap during use.
27 The V ersa- T ether can indicate when the child seat has been in a moderate or severe crash (see page 4) and replacement of the child seat is necessary . Figure 1 shows a tether acceptable for continued use (provided the child seat has not been involved in a crash).
28 L A TCH Installation Before Y ou Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit.
29 Install with LA TCH as shown above. IMPORT ANT : The buckle should be in the inner slot for rear -facing installation . Rear-F acing Installation.
30 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: Y ou may need to turn the front of the child seat toward you for easier access to the lower anchors.
31 Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location.
32 Lap-Shoulder Belt Installation Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock -offs is not required as long as the vehicle seat belt system is locked.
33 Install with lap-shoulder belt as shown above. IMPORT ANT : • The harness buckle strap should lie toward the back of the child seat during installation.
34 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow , unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear -facing belt path.
35 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location.
36 Lap Belt Installation Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • This child seat must be reclined to position 3 and placed rear-facing on the vehicle seat.
37 Install with lap belt as shown above. IMPORT ANT : • The harness buckle strap should lie toward the back of the child seat during installation. • DO NOT use lock-offs for lap belt installations. • The buckle should be in the inner slot for rear -facing installation.
38 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow , unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear -facing belt path.
39 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location.
40 Before Y ou Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit.
41 Install with LA TCH as shown above. WARNING! • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.
42 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: Y ou may need to turn the back of the child seat toward you for easier access to the vehicle lower anchors.
43 Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in.
44 Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock -offs is not required as long as the vehicle seat belt system is locked.
45 Install with lap-shoulder belt as shown above. WARNING! • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.
46 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Open the red lock-off closest to where the vehicle belt will be buckled.
47 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in.
48 Lap Belt Installation Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • Remove the Versa- T ether from the pouch and place it up and over the child seat back. * Britax recommends that the V ersa-T ether is used at all times.
49 Install with lap belt as shown above. 49 49 49 WARNING! • DO NOT use lock -offs for lap belt only installations. • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat.
50 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 5 Push the child seat down while pulling the vehicle belt to remove all slack (see pages 10 – 11).
51 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in.
52 This child seat is certified for aircraft use. Most airlines in the U .S. and Canada will allow the use of a child seat as long as it is labeled as an approved child seat for use in aircraft and fits properly on the aircraft seat. Contact the airline about their policy prior to traveling.
53 Securing Y our Child WARNING! • Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position.
54 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Open the chest clip. a Press tabs b Pull apart 3 Release the buckle and attach the harness straps to the harness holders. 4 Place the child in the child seat. * Ensure the child is positioned upright in the child seat and not slouching.
55 6 Fasten the harness buckle. * Proper connection is confirmed with a click after inserting each buckle tongue. 7 Pull the excess slack up to the child’s shoulder area while moving the HUGS ™ chest pads down toward the buckle. 8 Pull the harness adjuster strap up to tighten the harness.
56 Cover R emoval WARNING! • Never remove the buckle tongues from the harness. They cannot be reattached after removal. If reassembled incorrectly , the child seat may not perform as intended. • DO NOT remove the HUGS ™ chest pads from the harness straps.
57 6 Raise the harness to the highest position and detach the hook and loop fasteners on the head restraint cover from around the harness. 7 Detach the hook and loop fasteners on the head restraint cover from around the head restraint. 8 Detach the elastic straps from the tabs behind the harness adjustment handle.
58 13 Pull the buckle through the slot in the cover . Care and Maintenance 14 Remove the cover from the child seat shell. 1 4.
59 Care and Maintenance Cleaning the Cover • HAND WASH the cover using cold water and mild soap. • LINE DRY to prevent the cover from shrinking. • DO NOT : * Bleach * Machine wash * Machine dry * Iron Cleaning the Harness • SPONGE CLEAN the harness using warm water and mild soap.
60 Cover Replacement 1 Fit the child seat cover around the child seat shell. 3 Attach the plastic hooks to the bottom edge of the child seat. Care and Maintenance 2 Attach the plastic hooks on the cover to the back of the child seat shell. 4 Pull the buckle through the slot in the cover .
61 5 Fit the head restraint cover around the harness adjustment handle and attach the elastic straps to the tabs behind the harness adjustment handle. 6 Attach the hook and loop fasteners on the head restraint cover around the head restraint. 7 Attach the hook and loop fasteners on the head restraint cover around the harness.
62 Care and Maintenance Cleaning the Buckle If your child eats and drinks while in the child seat, you will need to check the buckle periodically and rinse out any accumulated debris. Remove the Buckle 2 T urn the buckle webbing and slide it between buckle positions.
63 Care and Maintenance 3 Guide the buckle retainer up through the slot in the child seat shell to remove. T o Clean: • THOROUGHL Y RINSE the buckle using warm water . • TEST THE BUCKLE by fastening and unfastening until a click is heard after inserting each buckle tongue.
64 Care and Maintenance Re-thread the Buckle 1 Guide the buckle retainer down through the slot in the child seat shell. 2 Slide the buckle webbing into the slot between buckle positions. 3 Select the appropriate slot for the size of your child and turn the buckle webbing and slide it into the chosen slot.
65 Tips and T roubleshooting T roubleshooting Problem: The harness cannot be adjusted to its full height. Possible Solution: Check the seating position where the child seat is installed. The vehicle head restraint may obstruct the path of the child seat harness height adjuster .
66 This child seat was manufactured by Britax Child Safety , Inc. Britax ® warrants this product to the original retail purchaser as follows: LIMITED ONE- YEAR WARRANTY This product is warranted against defective materials or work man ship for one year from the date of original purchase.
67.
Britax Child Safety , Inc. 13501 South Ridge Drive Charlotte, NC 28273 USA A Britax Childcare Group Limited company T el. : 1-888-427-4829 www .Britax.
An important point after buying a device Britax 70 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Britax 70 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Britax 70 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Britax 70 you will learn all the available features of the product, as well as information on its operation. The information that you get Britax 70 will certainly help you make a decision on the purchase.
If you already are a holder of Britax 70, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Britax 70.
However, one of the most important roles played by the user manual is to help in solving problems with Britax 70. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Britax 70 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
