Instruction/ maintenance manual of the product 6330 Brinkmann
Go to page of 36
6330 MAXIMUM SIDE BURNER WEIGHT = 15 lbs. OWNER’S MANUAL W ARNING HAZARDOUS EXPLOSION MA Y RESUL T IF THESE W ARNINGS AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL W ARNINGS AND INSTRUCTIONS IN THIS MANUAL T O A VOID PERSONAL INJUR Y , INCLUDING DEA TH OR PROPERTY DAMAGE.
1 WE W ANT YOU T O ASSEMBLE AND USE YOUR GRILL AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION T O POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
2 General W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and LP Cylinder Specifications and Safe Use . . . . . . . . . . . . . . 4–6 Connecting LP Cylinder and Hose / Regulator to Grill .
3 W ARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal briquets or lighter fluid in a gas grill. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill.
4 W ARNING W ARNING LP GAS CYLINDER (NOT SUPPLIED WITH THIS GRILL) The LP cylinder is available for purchase at the same location the grill was purchased. The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must have a 20 lb.
5 The cylinder must also be equipped with: • A shut-off valve terminating in a T ype 1 gas cylinder valve outlet. • A T ype 1 valve that prevents gas flow until a positive seal is obtained. • An arrangement for vapor withdrawal. • A collar to protect the cylinder shut-off valve.
FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder . • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity .
7 W ARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas grill must be used.
LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame.
W ARNING 9 6. Check each place listed (A – K) for growing bubbles which indicates a leak. 7. T urn off gas supply at cylinder valve. 8. T urn on control knobs to release gas pressure in hose. 9. T urn control knobs to "OFF" position. 10. T ighten any leaking connections.
LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the "OFF" position.
LIGHTING THE SIDE BURNER: 1. Open lid before lighting side burner . 2. Make sure control knob is in the "OFF" position. 3. Push and turn side burner control knob to the "HIGH" position. 4. Press the electronic igniter on the main control panel an d hold for 3 – 5 seconds to light burner .
12 OPERA TING THE GRILL: Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill.
ROTISSERIE COOKING: • Y our grill was pre-drilled from factory to include mounting holes for a rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie.
14 GRILL COOKING TIPS CLEANLINESS • Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw meat, uncooked poultry or seafood.
BURNER ASSEMBL Y/MAINTENANCE • Although your burners are constructed of stainless steel, they may rust as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage.
16 TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for Leak T esting.
17 TROUBLE SHOOTING Problem: Possible Causes: 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will match light. Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed.
18 Y our grill's serial number and model number , and the contact information for Brinkmann Customer Service, are listed on a silver label found on the back of the grill or on the grill body side, under the side shelf. These questions and answers are for your general knowledge, and may not be applicable to your model grill.
Cleaning Stainless Steel Cooking Grills: W ash grills with a mild detergent and rinse with hot water before initial use and as needed. DO NOT use a comm ercial oven cleaner . For stubborn food residue, use a degreaser and fiber or brass cleaning brush.
20 P AR TS BAG CONTENTS 1 Hex nut wrench 1 AA/1.5V Alkaline battery 1 Screwdriver 24 M6 X 12mm bolts Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process.
ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT . The estimated time of assembly for this grill is approximately 15 minutes.
(Proof of purchase will be required.) Inspect contents of the box to ensure all parts are included and undamaged. FOR MISSING P AR TS, PLEASE CALL CUSTOMER SERVICE A T 800-527-0717.
Choose a good, cleared assembly area and get a friend to help you put your grill together . Lay cardboard down to protect grill finish and assembly area.
Step 3 With the help of a friend, turn the assembled cart over . T ry to minimize the stress to the bottom plate. Step 4 Attach locking casters to the bottom of the left side cart panel. T ighten caster bolts securely using hex nut wrench provided in parts pack.
Step 6 Snap wheel hub caps onto the outside of wheels as illustrated. Step 7 With the help of a friend, turn the cart to its upright position. Step 8 Attach tank heat shield to heat shield plate using one #8 self-tapping screw . Step 9 Attach front panel to lower left and right leg of cart assembly using two M6 X 12mm bolts and star washers.
26 Step 10 Attach heat shield plate and front panel to the front of the cart frame assembly using two M6 X 12mm bolts with star washers. Step 1 1 Attach heat shield plate to the back of the cart frame assembly using two M6 X 12mm bolts with star washers.
27 Note: When performing Step 13, Lift grill body from front and rear panels to avoid injury to hands and fingers. Be sure to pass hose/regulator assembly above cart frame crossbar . Step 13 With the help of a friend, place grill body assembly on assembled cart frame.
28 Step 14 Attach side table to left side of cart frame assembly . Insert four M6 X 12mm bolts halfway into cart frame assembly . Step 15 Place table over bolts and slide toward front of grill, then tighten securely . Fasten side table front panel to grill body with one M6 X 12mm bolt.
29 Step 18 Attach the hose heat shield to the right side of the cart frame using two #8 self-tapping screws. Step 19 Remove two bolts and washers from the side burner valve. Insert the side burner valve assembly through the hole in the side burner front panel, then firmly seat the valve nozzle into the burner venturi.
Step 21 Attach side burner igniter lead wire to the electrode as illustrated. Step 22 Place side burner grate over side burner . Step 23 Insert grease tray into opening on backside of grill.
31 Step 24 Place the porcelain coated heat distribution plates on lower level of grill body assembly directly above burners. Step 25 Place porcelain cast iron cooking grills on support ribs directly above porcelain coated heat distribution plates. Step 26 Place warming rack in grooves so that it sits above the cooking grills.
32 6330 MAXIMUM SI DE BURNER WEIGHT = 15 lbs. ProSeries 6330 (Assembled) Step 28 Insert tank lock wire through two small holes in cart base as illustrated.
PROFESSIONAL SHISH-KABOB SKEWERS These heavy-duty , 18" shish-kabob skewers are extra-long for fabulous restaurant style kabobs. Made of rust resistant stainless steel to last for years. SET OF 12 812-2904-0 ACCESSORIES 33 RIB RACK Chrome-plated rack can greatly increase the cooking capacity of your grill.
ACCESSORIES LOOK FOR THESE AND OTHER BRINKMANN ACCESSORIES A T YOUR LOCAL RET AILER WHERE SMOKERS ARE SOLD, OR ORDER DIRECT BY CALLING 800-468-5252. MUL TI-PURPOSE SP A TULA If you could have only one.
140-6330-W 10/05 Owner ’s Manual for Model 810-6330-W ©2005 The Brinkmann Corporation Dallas, T exas 75244 U.S.A www .brinkmann.net The Brinkmann Corporation warrants to the original purchaser that.
An important point after buying a device Brinkmann 6330 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Brinkmann 6330 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Brinkmann 6330 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Brinkmann 6330 you will learn all the available features of the product, as well as information on its operation. The information that you get Brinkmann 6330 will certainly help you make a decision on the purchase.
If you already are a holder of Brinkmann 6330, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Brinkmann 6330.
However, one of the most important roles played by the user manual is to help in solving problems with Brinkmann 6330. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Brinkmann 6330 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
