Instruction/ maintenance manual of the product LT-200 Briggs & Stratton
Go to page of 14
1/2006 1 TP 300-4517-00-RG-SMAN Setup & Adjustment Instructions L T -200 Series T ractors and Mowers T ABLE OF CONTENTS: SAFETY RULES .................................................................2 SETUP PROCEDURES Quick Setup List ............
L T -200 Series TP 300-4517-00-RG-N 3/2007 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe personal injury or death to you, yourself or bystanders, or damage to property or equipment.
L T -200 Series 3/2007 3 TP 300-4517-00-RG-N Quick Setup List - P age Setup Procedure Steps to P erform 4 Uncrating o Remov e Crate & Banding. o Place T ransmission Release Le ver in PUSH position & Roll T ractor f orward off skid.
L T -200 Series TP 300-4517-00-RG-N 3/2007 4 Uncrating Using a reciprocating utility saw or equivalent, cut crate away from bottom skid. Remove crate. Remove shrink- wrap plastic. 2. Cut banding from front and rear tractor axles. Cut banding from mower rollers.
L T -200 Series 3/2007 5 TP 300-4517-00-RG-N Chec k Fluid Levels Check T ransmission Oil Level The K46 transmission is a sealed unit that is shipped with the correct oil level. However if a transmission’s oil level is suspect it can be checked. See Transmission Maintenance.
L T -200 Series TP 300-4517-00-RG-N 3/2007 6 Figure 4. Seat Switch A. Seat Switch B. Wiring Harness P erf orm Safety Chec ks Functional T ests 1. Check the tractor for loose bolts, screws, nuts, etc.
L T -200 Series 3/2007 7 TP 300-4517-00-RG-N Figure 5. Blade Torque A. 4x4 Wood Block B. Spline or Hex Washer C. Spring Washer D. Blade Bolt T or que Mower Blades 1. Secure the hex washer (B, Figure 5), spring washer (C) and capscew (D). Use a wooden block (A) to prevent blade rotation while tightening the blade bolt (D) to 45-55 ft.
L T -200 Series TP 300-4517-00-RG-N 3/2007 8 Lubrication Lubricate the unit at the locations shown in Figures 7-10 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
L T -200 Series 3/2007 9 TP 300-4517-00-RG-N Figure 8. Mower Lubrication Points Figure 10. Arbor Lubrication Point Figure 9. Mower Lubrication Points Hourmeter HOURMETER MODELS The hour meter measures the number of hours the key has been in the RUN position.
L T -200 Series TP 300-4517-00-RG-N 3/2007 10 Mower Dec k Remov al & Installation Removing the Mo wer Deck 1. Park tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine, remove the key and apply parking brake. 2.
L T -200 Series 3/2007 11 TP 300-4517-00-RG-N Leveling The Mo wer If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure.
L T -200 Series TP 300-4517-00-RG-N 3/2007 12 Gauge Wheels The mower gauge wheels can be placed in several positions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position. When using lower cutting heights, set the wheels in the upper position.
L T -200 Series 3/2007 13 TP 300-4517-00-RG-N Electric PT O Clutch Adjustment Check the PTO clutch adjustment after 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage.
L T -200 Series TP 300-4517-00-RG-N 3/2007 14 Mower Belt Replacement Note: It is not necessary to remove the mower to install a new belt. However, for easier access mower can be removed. See Mower Removal in the Operation section. 1. Park the tractor on a smooth, level surface such as a concrete floor.
An important point after buying a device Briggs & Stratton LT-200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton LT-200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton LT-200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton LT-200 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton LT-200 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton LT-200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton LT-200.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton LT-200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton LT-200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
