Instruction/ maintenance manual of the product 5900703 Briggs & Stratton
Go to page of 16
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 5900703 Clean Sweep Triple Catcher 1735596 Rev. 00 Rev. Date 10/2007 TP 100-4785-00-AT-SMAN Clean Sweep T riple Ca.
THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT).
1 Cover and Ba g Installation Install Cov er Assemb ly ....................................7 Install Collector Bags .......................................7 T ube Installation Low er T ube Installation ....................................8 Connecting Upper and Middle T ube .
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed.
CA UTION Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet, as well as the Operator’s Manual for the tractor and any other attachments. Never operate on slopes greater than 17.
4 BAFFLE INSTALLATION 1. Determine which baffle to use (See Chart). 2. Lift side discharge chute (H, Figure 1). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4 . Tighten carriage bolts (A) and locknut(s) (E) on baffle (F).
5 Component Installation Figure 3. Lower Chute to Boot Installation A. Latch Pin B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Rubber Strap G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J.
6 Bag and Cover Support Installation INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 5) to upright support (A) using the capscrews (C) and the locknuts (D). A B Figure 5. Install Bag and Cover Support A. Upright Support B.
Cover and Bag Installation 7 Figure 6. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 6) to bag support bracket (A) using hinge pivots (E).
T ube Installation 8 LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 8). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole closest to knob in strap completely over locknut (E).
9 A. Hitch Support Assembly J. Deflector B. Cover K. Nut & Capscrew C. Pins L. Mounting Plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R.
10 Carrier Installation Figure 12. Front Weight Carrier Installation A. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknuts, 1/2-13 FRONT WEIGHT CARRIER INSTALLATION 1. Install carrier (F, Fgure 12) as shown securing with capscrews (B), and locknuts (C).
11 Hitch Plate and Back Plate Installation FLAT STYLE BUMBER 1. Remove and discard hardware holding heat shield (B, Figure 13) to upper and lower bumper (E). 2. Open existing holes (F) in heat shield (B) and upper & lower bumper (E) to 17/32”. 3.
12 Grass Catcher Removal an d Attachment REMOVING THE GRASS CATCHER 1. Remove the hair pin clips (B, Figure 16) and hinge pins (D) and remove the cover (A). A B C D Figure 16. Remove the Cover A. Cover C. Hinge B. Hair Pin Clip E. Hinge Pin 2. Remove the bags (A, Figure 17) by tilting them off their hooks.
13 Grass Catcher Removal and Attachment ATTACHING THE GRASS CATCHER 1. Set the back plate and support (A, Figure 19) onto the pins of the hitch plate (C).
Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & Stratton Corporation Milwaukee, WI USA.
An important point after buying a device Briggs & Stratton 5900703 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton 5900703 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton 5900703 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton 5900703 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton 5900703 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton 5900703, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton 5900703.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton 5900703. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton 5900703 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
