



vTouch allows for touch feedback control for external monitors connected to a Mac.
The touch function relates to the processing of the touch events (tap, press, gestures, etc.) performed on the touch device. A common list of touch events and system actions are predefined and can be configured as suits.

vTouch can be downloaded at the “Download” section of each TD display’s product page.
After the download completes, launch the setup file and follow the on-screen directions to install the software.




UPDD Commander · UPDD Console





Below are the observed differences when installing UPDD kernel extension version. These instructions refer to drivers created on or after 8th December 2020 that carry the new universal binary codeless kext.
Intel systems The new codeless kext file caused kext load error 71 (an unknown error).
You still need to give manual permission to load the kext via the “Allow” button in the Security and privacy dialog to approve the installation of the UPDD software.
Silicon systems In our initial tests with the new codeless version of the kext we were not asked for permission to load the kext nor required to reboot for the kext to load.
However, your system may still ask to grant permission to load and require a reboot as shown below.
If this is required, and you have not granted permission, Kext error 27 will likely be shown in the UPDD Console. You have to reduce system security to allow the kext to load.


In addition to downloading the driver, ensure that your monitor and MacBook are properly connected via:



This section will describe the general use and operation of the UPDD applications. UPDD Commander
UPDD Commander can setup touch behavior definitions in all applications.
Setup Touch Behaviors for All Applications The touch function options are based on the Mac trackpad. The Touch function relates to the processing of the touch events (tap, press, gestures, etc.) performed on the touch device. A common list of touch events and system actions are predefined and can be configured as suits.


Setup Touch Behaviors for Specific Applications If the touch behaviors under All Applications are not enough for your use case, you can customize touch behaviors for specific applications. To activate, ensure UPDD Commander is open and go to: View > Show Hidden Application Groups.



Adjusting the Settings Adjusting the settings here will affect the universal settings of the UPDD Commander application. There are three setting tabs: General, Touch Behavior, and On-Screen Keyboard.

General Adjust general usage settings, and reset options (
).

Touch Behavior Customize touch screen behavior settings.


On-Screen Keyboard Choose the type of keyboard, and when to use it.

Accessibility Keyboard.
Reset All Touch Gestures to Default Sets all touch gestures and actions back to default.


UPDD Console can view, update, and configure the driver and installed devices.
Console View the Device List, Function Bar, and Settings. The Function Bar consists of Touch, Calibration, Toolbars, Devices, and About.

Function Description Touch Touch settings and test options
Toolbars Label and calibrate your toolbars
Devices Installed and supported devices list
About Release information of the software
Calibration Calibration settings

Setting Description Interlock Indicates the touch priority given to the device.
Low Pass Filter Smooths input and removes jitter from inputs subject to distortion.
Indicates that a press and hold will generate a right click. For MacOS, gestures need be set for right click processing if required.
Assists double clicking by generating a second touch at the same location of the previous one. The second click needs to be within a certain time and distance (width) of the first click.
Assisted Double Click Time
When enabled the tip switch bit (AKA lift bit) is ignored. Normally used in conjunction with a non-zero value for liftoff_ time_ms. Can also be useful if when dragging the device it occasionally generates unwanted pen up packets that you wish to ignore.
Enabled Indicates touch is enabled. Can be used to disable touch for the device.
Interactive Touch · Ignore Tip Switch

Reset Settings Reset general/device settings back to the default settings. The option can be found under General in the left hand column.









You install the UPDD driver and still cannot find the device.

You want to remove the setting files before installing a new version of UPDD.
upddcommander ͫ upddprocesses start -c
vTouch_Support_UG_ENG Rev. 1A 2021-08-20
Problem Solution


Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| You install the UPDD driver and still cannot find the device. | 1. Run console and view the error information. 2. When the driver is installed you may see the following message: 3. Ensure the software has been enabled, otherwise the driver will not be able to access any USB devices. This can be checked in: System Preferences > Security & Privacy > General. | p.18 | |
| You want to remove the setting files before installing a new version of UPDD. | 1. Open a terminal window. 2. Run the following commands: ͫ upddprocesses stop -c ͫ defaults delete com.touch-base. upddcommander ͫ upddprocesses start -c | p.18 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.