Instruction/ maintenance manual of the product 2600 Briggs & Stratton
Go to page of 10
1 Installation Instructions Sub-Frame Hitch Mfg. No . 1695196 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors This kit is required when installing front mounted snowthrowers.
2 Installation Instructions Sub-Frame Hitch Early Manual Lift Only (See Instructions) Hydraulic Lift 47 16 28 27 25 33 40 41 39 38 37 36 43 51 42 33 25 29 29 29 28 28 27 50 17 13 11 14 9 12 13 11 19 1.
3 Sub-Frame Hitch Installation Instructions Ref Part No. Qty. Description 1 1723292A 1 SHAFT & HOOK ASSY 2 1653768A 1 CLAMP, Support 3 1931335 4 CARRIAGE BOLT, 5/16-18 x 1 4 1919381 4 WASHER, 11/32 5 1917356 3 LOCKWASHER, 5/16 6 1917372 4 NUT, 5/16-18 7 105249 1 PIN, Round Head, 3/8 x 2-3/8 8 1724025 1 LIFT LEVER ASSY.
4 Installation Instructions Sub-Frame Hitch Figure 2. Install Support Clamp A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer B. Hook Assembly E. 5/16 Lockwasher C. Support Clamp F. 5/16-18 Nut B C D E A F Figure 4. Assemble Lift Rod A. Lift Rod C. Spring B.
5 Sub-Frame Hitch Installation Instructions INITIAL INST ALLA TION Manual Lift Models LIFT LINK - EARLY VS. LATER The early model lift link (A, Figure 5) was used on early production Conquest/1700/2700 Series tractors. It must be replaced with the later model lift link (B) included with this attachment.
6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod Install Hitch 1. Slide the hitch under the tractor. 2. Raise the rear of the hitch and place the hook (C) over the lift shaft.
7 Sub-Frame Hitch Installation Instructions Install Lift Rod 1. Slide the lift lever (A, Figure 9) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C).
Installation Instructions Sub-Frame Hitch REMO V AL NOTE: After removing components, reinstall the clevis pins and clips to prevent loss. 1. Disconnect the lift rod from the attachment and lift lever extension (C, Figure 11). 2. Remove the clevis pin and clip from the lift lever (C) and remove the lift lever.
9 Sub-Frame Hitch Installation Instructions A F C D G Figure 13. Lift Link - Manual Lift Models A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G.
Installation Instructions Sub-Frame Hitch Form No. 1733911-04 Rev. 01/2007 © 2007 Briggs & Stratton, Inc. All Rights Reserved TP 200-4417-04-AT-SMAN MANUFACTURING, INC.
An important point after buying a device Briggs & Stratton 2600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton 2600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton 2600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton 2600 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton 2600 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton 2600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton 2600.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton 2600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton 2600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
