Instruction/ maintenance manual of the product 1695734 Briggs & Stratton
Go to page of 8
© Briggs & Stratton Corporation Dual Stage Sno wthro w er 1752198 (Rev. B) Setup Instructions 1695734 1695735 1695820 1695843 1695853 1695906 1695908 1695909 1695964 1695986 1695987 1695988 1696001 1696002 1696003 1696004 1696005 1696006 1696007 1696025 1696026 1696027 1696083 Model Nos.
2 EN 1 Loosen upper fasteners. 2 Remove lower fasteners. 3 Carefully lift handle to the operating position while guiding the speed control rod over the tire. 4 Make sure Z-fittings are secured in holes of control levers. 5 Make sure cables are not caught between the upper and lower handle.
3 EN 1 Attach speed control rod to shift yoke and secure with lock washer and nut. FR 1 Fixez la tige de commande de vitesse à la fourchette de boîte et sécurisez-la avec une rondelle frein et un écrou. 1/2” 7/16” 1 2A EN 1 Move speed control lever to the full forward (6th gear) position.
4 3/8” 7/16” 66 lb-in (7.6 Nm) 1 3 2 3A EN 1 Align slot in chute ring with arrow on mounting ring. 2 Install fasteners and tighten securely, but do not overtighten. 3 Install cable ties as shown. FR 1 Alignez la fente dans l’anneau de l’éjecteur sur la flèche de l’anneau de montage.
5 EN 1 When facing chute opening, install a retainer on the right and back side of the chute ring. Tighten fasteners securely. 2 Apply grease to the top and bottom surfaces of the mounting ring. 3 Install chute making sure that the mounting ring is between the chute ring and retainers.
6 EN 1 Align holes in chute ring with holes in chute as shown. 2 Install fasteners and tighten securely, but do not overtighten. 3 Connect wire harness. FR 1 Alignez les orifices dans l’anneau de l’éjecteur sur les orifices dans l’éjecteur comme illustré.
7 1 EN 1 Adjust the skid shoes so that the scraper bar has 1/8-3/16” clearance above a hard surface or 1” clearance above a gravel surface. FR 1 Ajustez les sabots de patin pour que la barre du racloir ait un espacement de 1/8-3/16 po. au-dessus d’une surface dure ou de 1 po.
8 EN 1 Tires are over-inflated for shipping purposes. Check tire air pressure with an accurate gauge. The maximum pressure is stamped on the sidewall of the tires. WARNING • Do not inflate the tires above the maximum pressure. • Do not stand in front or over the tire assembly when inflating.
An important point after buying a device Briggs & Stratton 1695734 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton 1695734 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton 1695734 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton 1695734 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton 1695734 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton 1695734, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton 1695734.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton 1695734. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton 1695734 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
