Instruction/ maintenance manual of the product 1694919 Briggs & Stratton
Go to page of 20
A TT A CHMENT OPERA T OR’S MANU AL 42” Snow Blade Mfg. No. Description 1694919 42” Remote Angling Snow Blade 42” Sno w Blade 1732529 Revision 01 Rev.
.
1 T able of Contents T roub leshooting, Adjustments & Service T roub leshooting Char t .....................................8 Skid Shoe Adjustment .....................................9 Lift Adjustment .............................................
2 Safety Rules & Information TP-600-4159-01-UV-SMAN OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads.
3 Features & Controls TRA CT OR CONTR OLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual.
General Operating Instructions 4 Checks Bef ore Star ting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity.
5 General Operating Instructions Daily Stora g e 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion.
6 Notes.
7 Maintenance Schedule For Normal Care General Lubrication Lubricate the snow blade as shown in Figure 2. Where an oil can is shown use 30 weight oil. Where a grease gun is shown, use lithium grease. Lubricate the following areas: • Grease the blade pivot.
8 T roubleshooting, Adjustments, & Service TR OUBLESHOO TING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.
9 T roubleshooting, Adjustments, & Service Figure 3. Skid Shoe Adjustment A – Lock Nut B – Skid Shoe Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be set high enough so that it will not pick up debris.
Ref Qty Description 1 1 Lift Assist Spring 2 7 Hair pin 3 1 Flat Washer 4 1 Lift Arm 5 1 Stand Off 6 1 Lock Washer 7 1 Bolt 8 1 Hitch Assembly 9 1 Bell Crank 10 2 Mounting Pin 11 1 Hitch Pivot Assembl.
11 Initial Setup & Assembly A B Figure 6. Bell Crank Installation A. Chute Rotator Drive Cover Bolt B. Chute Rotator Drive Cover Install Hitch on to T ractor 1. Remove mower deck. 2. Install the bell crank (A, Figure 6) through the front holes (B) of the hitch assembly.
12 Initial Setup & Assembly Figure 8. Hitch Installation A. Hitch Assembly B. Hitch Support Shaft C. Hitch Mounting Arms 5. Slide hitch (A, Figure 8) under tractor and lift to slide hitch mounting arms (C) over hitch support shaft (B).
13 Initial Setup & Assembly Install Snow Blade Lift Arm 1. Move the mower deck lift arm to the “LOWERED” position. 2. Install the brass stand-off (A, Figure 10) at the top of the mower deck lift arm (B), using bolt (C) and wash- er (D).
14 Initial Setup & Assembly Figure 11. Snow Blade Assembly A. Pivot Assembly B. Whiz Lock Nut C. Snow Blade Assembly D. Tension Spring E. Eyebolt F. Nut G. Capscrew H. Flat Washer I. Spacer A B C Figure 12. Attaching Snow Blade to Hitch A. Mounting Pin B.
15 Initial Setup & Assembly A E C G D B H F Figure 13. Blade Control Arm Installation A. Control Arm Support Bracket B. Flange Nut C. Bolt D. Eyebolt E. Upper Control Arm F. Lower Control Arm G. Nut H. Bolt E C A D B Figure 14. Lower Control Arm Installation A.
16 Removal Snow Blade Remo val 1. Lower the snow blade to the ground. 2. Remove the four (4) hair pins (C, Figure 16) from the control arm (A) and remove the control arm from the snow blade assembly. 3. Remove the control arm from the tractor. NOTE: The control arm support bracket can be left on the tractor.
17 Removal 6. Remove the snow blade hair pin (B, Figure 18) and mounting pin (A). 7. Slide the snow blade assembly away from the tractor. 8. Remove the lower latch pin (A, Figure 19) from the front of the hitch assembly. 9. Lift the hitch assembly off of the support fingers (C).
500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 AGCOLawn.
An important point after buying a device Briggs & Stratton 1694919 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Briggs & Stratton 1694919 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Briggs & Stratton 1694919 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Briggs & Stratton 1694919 you will learn all the available features of the product, as well as information on its operation. The information that you get Briggs & Stratton 1694919 will certainly help you make a decision on the purchase.
If you already are a holder of Briggs & Stratton 1694919, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Briggs & Stratton 1694919.
However, one of the most important roles played by the user manual is to help in solving problems with Briggs & Stratton 1694919. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Briggs & Stratton 1694919 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
