EN
Boss logo
Official user manual

Boss Loop Station

28 pages·635 KB·Guitar Pedal·PDF·ENDEFRITNLJA
Boss Loop Station
Table of Contents 39 sections Getting Ready · Installing the Batteries · Connecting the Equipment · Top Panel · … ShowHide
Page 1 of the Boss Loop Station user manual — Owner’s Manual
Page 1 · click to enlarge
Page 1

Owner’s Manual

Getting Ready 2 Installing the Batteries 2 Connecting the Equipment 2 Top Panel 4 How the RC-500 Is Organized 6

Connecting a Computer via USB 18 Connecting the RC-500 and Computer 18 Backing-Up or Recovering Data 19

Controlling Devices via MIDI 20 MIDI Settings 20

Creating a Loop Phrase 7 Recording on a Single Track 7 Recording on Two Tracks 8 Record While Listening to the Rhythm Sound 9 Sounding a Rhythm 9 Setting the Tempo of Rhythm 9

Controlling an External MIDI Device from the RC-500 20 Controlling the RC-500 from an External MIDI Device 21 Connecting Two RC-500 Units 21

Appendix 22 Troubleshooting 22 Error Message List 23 Restoring the Factory Default Settings (Factory Reset) 25 Main Specifications 26

Saving a Memory 10 Saving a Memory (WRITE) 10 Erasing Data from a Memory (CLEAR) 10

Editing a Memory 11 Editing the Settings of Tracks 1 and 2 11 Editing the Settings of a Memory 12

USING THE UNIT SAFELY 27

Using the Loop FX 13 Specifying the Function of the Switches 13 Editing the Rhythm Settings 14

Changing How the Rhythm Starts and Stops . . . 15

Settings for the Entire RC-500 16 System Settings 16 Input/Output Settings 17

Boss Loop Station — Owner’s Manual diagram (page 1)
Fig. 1 · Owner’s Manual

Read this first. It explains the basic things you need to know in order to use the RC-500.

This explains all of the parameters of the RC-500.

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaflet “USING THE UNIT SAFELY” and the Owner’s Manual (p. 27)). After reading, keep the document(s) where it will be available for immediate reference.

Page 2 of the Boss Loop Station user manual — MIDI OUT, MIDI IN connectors
Page 2 · click to enlarge
Page 2

Getting Ready

Installing the Batteries

Install four alkaline batteries (AA, LR6) in the battery compartment located on the bottom of the unit.

* When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle the unit carefully; do not drop it.

* If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (separate sheet “USING THE UNIT SAFELY” and owner’s manual (p. 27)).

* “BATTERY LOW” will appear on the display if the batteries are low. Replace them with new ones.

Boss Loop Station — Getting Ready diagram (page 2)
Fig. 2 · Getting Ready

You can attach the rubber feet (included) if necessary. Attach them in the locations shown in the illustration.

Connecting the Equipment

* To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.

* Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

O (USB ) port

DC IN jack

You can connect your computer here and use it to back up or recover data (p. 19).

Accepts connection of an AC Adaptor (PSA-S series; sold separately). By using an AC Adaptor, you can play without being concerned about how much battery power you have left.

If the AC adaptor is connected while power is on, the power supply is drawn from the AC adaptor.

* Use only the specified AC adaptor (PSA-S series; sold separately), and connect it to an AC outlet of the correct voltage. Do not use any other AC adaptor, since this may cause malfunction.

Boss Loop Station — DC IN jack diagram (page 2)
Fig. 3 · DC IN jack

1: GND 2: HOT

3: COLD

Boss Loop Station — 1: GND 2: HOT diagram (page 2)
Fig. 4
Boss Loop Station — 1: GND 2: HOT diagram (page 2)
Fig. 5

MIDI OUT, MIDI IN connectors

Connect an external MIDI device here. To make these connections, use TRS/MIDI connecting cables (sold separately: BMIDI-5-35). This lets you control an external MIDI device from this unit via MIDI. For details, refer to p. 20.

Pin assignment · MIC IN connector

Page 3 of the Boss Loop Station user manual — FS-6
Page 3 · click to enlarge
Page 3

Getting Ready

INST IN jacks (A/MONO, B)OUTPUT jacks (A/MONO, B) Connect your electric guitar/bass or efefct uni to these jacks. Use the A/MONO jack and B jack when connecting a stereooutput efefcts unit. Use only the A/MONO jack if you’re using a mono source.Connect your electric guitar/bass or efefct uni to these jacks. Use the A/MONO jack and B jack when connecting a stereooutput efefcts unit. Use only the A/MONO jack if you’re using a mono source.t Connect these jacks to your amp or monitor speakers. If you’re using a mono setup, use only the A/MONO jack. Even sound that is input in stereo is output in mono. Turning the power on/off The OUTPUT A/MONO jack doubles as the power switch. Power to the unit is turned on when you plug into the OUTPUT A/MONO jack; the power is turned off when the cable is unplugged. When powering up: MIC IN connectorTurn on the power to your amp last.

Connect your microphone here.

When powering down: Turn off the power to your amp first.

If you’re using a condenser mic that requires phantom power, turn on this unit’s phantom power (p. 17).

CTL 1, 2/EXP jack

Boss Loop Station — Getting Ready diagram (page 3)
Fig. 6 · Getting Ready
Boss Loop Station — Getting Ready diagram (page 3)
Fig. 7 · Getting Ready

CTL 1, 2/EXP jack

You can connect separately sold expression pedal or footswitches to this jack, and use the expression pedal or footswitches to control a variety of functions.

Use only the specified expression pedal (FV-500H, FV-500L, EV-30, and Roland EV-5; sold separately).

By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

To use this as EXP jack Connect an expression pedal.

To use this as CTL 1, 2 jack Connect a footswitch.

FS-6 FS-7

Stereo 1/4” phone type

Stereo 1/4” phone type

Stereo 1/4” phone type

FS-5U

1/4” phone type x 2

Stereo 1/4” phone type

Stereo 1/4” phone type

FS-6

RING TIP

CTL 2

FS-7

CTL 1 CTL 2

CTL 1 CTL 2 CTL 1 CTL 1

Show 7 more labels / short text on this page
Connecting the Equipment · Pin assignment · FS-5U x 2 · FS-5U x 1 · Mode/Polarity switch · 1/4” phone type · 1/4” phone type
Page 4 of the Boss Loop Station user manual — 11 12 13
Page 4 · click to enlarge
Page 4

Getting Ready

Top Panel

Boss Loop Station — Getting Ready diagram (page 4)
Fig. 8 · Getting Ready
Boss Loop Station — Getting Ready diagram (page 4)
Fig. 9 · Getting Ready

Selects a memory. When editing, selects a parameter or changes a value.

4 5 6 7

Pressing Specifies the parameter to edit. Alternatively, confirms an operation.

Turn while pressing Changes a value in larger steps.

11 12 13

Boss Loop Station — 11 12 13 diagram (page 4)
Fig. 10
Name / Explanation 1 TRACK 1, 2 [TRACK 1], [TRACK 2] slidersAdjust the playback levels of tracks 1 and 2. TRACK 1, 2 indicatorsIndicate the status of the tracks. Lit blueNo phrase Lit redRecording Lit greenPlaying Lit yellowOverdubbing Lit whitePhrase exists BlinkCurrently selected track (current track) TRACK 1, 2 [EDIT] buttonsPress to make track settings. Press a button twice to switch the current track. 2 Display

Press to specify the tempo of the rhythm. You can also set the tempo by pressing the button at the desired interval (tap tempo).

Each time you press the button, the rhythm switches on/off/standby. Long-press the button (two seconds or longer) to select rhythm settings mode.

Lets you make settings for loop play/record, and specify the function of an expression pedal or footswitch connected to this unit.

Shows various information of the RC-500. During recording/playback/overdubbing, the color of the screen changes according to the status.

Boss Loop Station — 11 12 13 diagram (page 4)
Fig. 11
Lit blueNo phrase Lit redRecording Lit greenPlaying Lit yellowOverdubbing Lit whitePhrase exists

Lets you make settings that affect the entire RC-500, such as system settings and MIDI settings.

Page 5 of the Boss Loop Station user manual — MEMO
Page 5 · click to enlarge
Page 5

Getting Ready

Name / Explanation 7 WRITE [EXIT] buttonPress to return to the previous screen. [ENTER] buttonPress to confirm an operation. By pressing the [EXIT] button and [ENTER] button simultaneously, you can save a memory (write) or erase (clear) memory data. 8 [MIC LEVEL] knob Adjusts the mic input level. 9 INPUT indicators These are lit according to the input level. Low Suitable High , , Green Orange Red Adjust the input level so that the indicator is occasionally lit red. * With the factory settings, the indicators are set to show the input level of the MIC IN and INST IN mixed together. You can switch what is shown. 10 [INPUT] button Press to turn phantom power on/of,f or to make settings related to input and output. 11 [REC/PLAY] switch
Boss Loop Station — Getting Ready diagram (page 5)
Fig. 12 · Getting Ready
Boss Loop Station — Getting Ready diagram (page 5)
Fig. 13 · Getting Ready

Stops the track that is currently recording/playing/ overdubbing. If you long-press the switch (two seconds or longer), the track is cleared.

Switches between tracks 1 and 2.

MEMO

You can assign other functions to the [REC/PLAY], [STOP], and [TRACK SELECT] switches. For details, refer to “Specifying the Function of the Switches” (p. 13).

Low,Suitable,High GreenOrangeRed

Switches between recording, playback, and overdubbing.

For an empty phrase Recording0Playback0Overdubbing

For a phrase that contains data Playback0Overdubbing

Long press (two seconds or longer) the switch during playback or overdubbing to Undo (cancel the recording or the last overdubbing). Long press (two seconds or longer) the switch once again to Redo (cancel the Undo).

Page 6 of the Boss Loop Station user manual — Getting Ready
Page 6 · click to enlarge
Page 6

Getting Ready

How the RC-500 Is Organized

Boss Loop Station — Getting Ready diagram (page 6)
Fig. 14 · Getting Ready
Boss Loop Station — Getting Ready diagram (page 6)
Fig. 15 · Getting Ready

In this manual, we refer to the act of recording to an empty track for the first time as “recording.” Any subsequent recordings that are made, which are added on top of the existing recording, we refer to as “overdubbning.”

Boss Loop Station — Getting Ready diagram (page 6)
Fig. 16 · Getting Ready

The screen that appears after you turn on the power is called the “Play screen.”

Track You can use two “tracks” to record and play back audio from a mic or from an instrument such as guitar.

Loop FX The effect applied to the tracks is called the “loop FX.” By applying the loop FX, you can change how the loop plays back.

Rhythm In addition to the two tracks, the RC-500 can also play a “Rhythm.” You can record while listening to a rhythm at the tempo you specify.

Memory The two tracks, together with the “rhythm” and “loop FX” settings, are collectively called a “memory.” The RC-500 can store up to 99 memories.

System Settings that are common to the entire RC-500, such as the display contrast adjustment and MIDI settings, are called “system settings.”

Page 7 of the Boss Loop Station user manual — MEMO
Page 7 · click to enlarge
Page 7

Creating a Loop Phrase

Recording on a Single Track

Getting ready to record

Recording 1. Press the [REC/PLAY] switch to start recording. The screen and the REC/PLAY indicator are lit red. 2. Play your guitar or vocalize into your mic to input audio. % Playback 1. Press the [REC/PLAY] switch. The screen and the REC/PLAY indicator are lit green. The recorded phrase plays as a loop. % Overdubbing 1. Press the [REC/PLAY] switch to start overdubbing. The screen and the REC/PLAY indicator are lit yellow. 2. Overdub-record your performance (audio) onto the phrase that’s playing as a loop. % Playback %$ Repeat as many times as necessary. Overdubbing : Stopping 1. Press the [STOP] switch. The screen and the REC/PLAY indicator are lit white. If you want to keep the recorded phrase, save it in a memory (p. 10).
1. Connect your guitar or mic.

* If a mic is connected, use the [MIC LEVEL] knob to adjust the mic input level.

2. Turn the [MEMORY/VALUE] knob to select a memory.
01 Memory 01ScreenStatus Blue White
3. Press the [TRACK SELECT] switch to the track 1 or 2.
TRACK indicator status Lit blueNo phrase Blink blueNo phrase (current track) Lit whitePhrase exists Blink whitePhrase exists (current track)

MEMO

The track that is currently selected (currently the target of operations) is called the “current track.”

Page 8 of the Boss Loop Station user manual — %
Page 8 · click to enlarge
Page 8

Creating a Loop Phrase

Recording on Two Tracks

You can use two tracks to create a single loop phrase.

In this example, we explain how to record in the order of “track 1” 0 “track 2.”

Press the [TRACK SELECT] switch to select track 1. % Recording (Track 1) 1. Press the [REC/PLAY] switch to start recording. The screen and the REC/PLAY indicator are lit red. 2. Play your guitar or vocalize into your mic to input audio. % Playback (Track 1) 1. Press the [REC/PLAY] switch. The screen and the REC/PLAY indicator are lit green. The recorded phrase plays as a loop. %$ Repeat as many times as necessary. Overdubbing (Track 1) 1. Press the [REC/PLAY] switch to start overdubbing. The screen and the REC/PLAY indicator are lit yellow. 2. Overdub-record your performance (audio) onto the phrase that’s playing as a loop. : Playback (Track 1) Press the [REC/PLAY] switch to start overdubbing. % Press the [TRACK SELECT] switch to select track 2.
Recording (Track 2) 1. Press the [REC/PLAY] switch to start recording. The screen and the REC/PLAY indicator are lit red. 2. Record your performance while you listen to the loop playback of track 1. % Playback (Track 2) 1. Press the [REC/PLAY] switch. The screen and the REC/PLAY indicator are lit green. The phrase recorded on track 2 plays as a loop. % Overdubbing (Track 2) %$ Repeat as many times as necessary. Playback (Track 2) : Stopping 1. Press the [STOP] switch. The screen and the REC/PLAY indicator are lit white. If you want to keep the recorded phrase, save it in a memory (p. 10).

%

Page 9 of the Boss Loop Station user manual — MEMO
Page 9 · click to enlarge
Page 9

Creating a Loop Phrase

Record While Listening to the Rhythm Sound

In addition to the two tracks, the RC-500 can also play a “Rhythm.” You can record while listening to a rhythm at the tempo you specify.

Sounding a Rhythm

5 The specified tempo can be saved as a setting in

memory.

1. Press the RHYTHM [ON/OFF] button. The rhythm switches on/off/ready to play rhythm each time you press the button. When the rhythm is on, the RHYTHM ON/OFF indicator is lit.

& “Saving a Memory (WRITE)” (p. 10)

5 You can specify the volume and type of rhythm,

and how the rhythm plays.

& “Editing the Rhythm Settings” (p. 14)

Setting the Tempo of Rhythm

1. Press the RHYTHM [TEMPO] button. The tempo setting screen appears.

TEMPO

120.0 J

2. While the tempo setting screen is shown, turn the [MEMORY/VALUE] knob to set the tempo.

Value 40.0–300.0

Tap tempo

You can set the tempo by pressing a button at the desired interval.

1. Press the RHYTHM [TEMPO] button several times in time with the desired tempo.

MEMO

If you long-press the RHYTHM [TEMPO] button (two seconds or longer), the tempo returns to the default value.

Page 10 of the Boss Loop Station user manual — MEMO
Page 10 · click to enlarge
Page 10

Saving a Memory

Saving a Memory (WRITE)

Erasing Data from a Memory (CLEAR)

If you select a different memory or turn off the power after recording or editing the settings, the recorded content or edited settings will be lost. If you want to keep the data, you must save it.

You can erase the data that is saved in a memory, clearing that memory to an empty state.

5 CONTROL settings (p. 12)

* If CTL1–2 PREF is “MEMORY”

5 “Assign” settings (p. 12)

1. Press the [EXIT] button and [ENTER] button simultaneously. The UTILITY screen appears.
1. Press the [EXIT] button and [ENTER] button simultaneously. The UTILITY screen appears.

UTILITY

UTILITY

WRITE J

WRITE J

2. Turn the [MEMORY/VALUE] knob to select “WRITE,” and press the [MEMORY/VALUE] knob.
2. Turn the [MEMORY/VALUE] knob to select “CLEAR,” and press the [MEMORY/VALUE] knob.

WRITE:01

J

CLEAR:01

J

Memory to be cleared

Memory01

Memory01

3. Turn the [MEMORY/VALUE] knob to select the save-destination memory.
3. Turn the [MEMORY/VALUE] knob to select the memory that you want to clear.

5 This procedure is not required if the memory number

5 This procedure is not required if the memory number

is acceptable as is.

is acceptable as is.

5 If you decide to cancel, press the [EXIT] button.

5 If you decide to cancel, press the [EXIT] button.

4. Press the [MEMORY/VALUE] knob or [ENTER] button. The memory will be saved.
4. Press the [MEMORY/VALUE] knob or [ENTER] button. The memory will be cleared.

* Do not turn off the power while the “EXECUTING...” message is shown.

* Do not turn off the power while the “EXECUTING...” message is shown.

MEMO

You can assign a name to the memory. For details, refer to “Parameter Guide” (PDF).

Show 4 more labels / short text on this page
5 Record/playback settings · Save-destination memory · Memory name · Memory name
Page 11 of the Boss Loop Station user manual — 100 J
Page 11 · click to enlarge
Page 11

Editing a Memory

Editing the Settings of Tracks 1 and 2

You can specify the volume and playback method for track 1 and track 2.

For details on the parameters, refer to “Parameter Guide” (PDF).

ParameterExplanation REVERSESpecifies whether to play back normally or in reverse. LOOP FXSpecifies whether to apply the loop FX. 1SHOTSpecifies whether to play back as oneshot or as the usual loop playback. LEVELAdjusts the playback level of the track. You can also use the [TRACK 1] and [TRACK 2] sliders to adjust the playback level. PANSpecifies the stereo position (pan) of the track. STARTSpecifies whether playback starts with a fade-in or immediately when the track plays. STOPSpecifies how the track stops. MEASURESpecifies the number of measures in the track. LOOP.S (LOOP SYNC)Specifies whether the beginning of the track 1 and track 2 phrases are aligned fo loop playback, or whether they loop-pla at the length of their respective phrases. TEMPO.S (TEMPO SYNC)Specifies whether each track plays at its original tempo (the tempo during recording) or at the tempo that is specified in memory. INPUTSpecifies the input from which sound is recorded. OUTPUTSpecifies the output destination of the playback audio.

Here we explain how to edit the settings of track 1. The procedure is the same when editing track 2.

1. Select the memory for which you want to edit the track settings.
2. Press the TRACK 1 [EDIT] button. The track settings screen appears.

J

T1 REVERSE

OFF

3. Turn the [MEMORY/VALUE] knob to select the parameter that you want to edit, and press the [MEMORY/VALUE] knob.

T1 LEVEL

100 J

4. Turn the [MEMORY/VALUE] knob to change the value, and press the [MEMORY/VALUE] knob.
5. Repeat steps 3–4 to edit the parameter that you want.
6. Press the TRACK 1 [EDIT] or [EXIT] button to return to the play screen.
7. If you want to save the edited settings, execute the Write operation (p. 10).

Parameter · Value

Page 12 of the Boss Loop Station user manual — REPEAT1 J
Page 12 · click to enlarge
Page 12

Editing a Memory

Editing the Settings of a Memory

Here’s how to edit the settings of each memory.

For details on the parameters, refer to “Parameter Guide” (PDF).

ItemExplanation RECMake settings related to recording/ overdubbing. PLAYSpecify how loop phrases play back. LOOP FXMake settings for loop FX. RHYTHMMake rhythm settings. CONTROLSpecify the functions of the [REC/PLAY] switch, [STOP] switch, [TRACK SELECT] switch, and a footswitch or expression pedal connected to the CTL 1, 2/EXP jack. * With the factory settings, these perform the functions that are specified by the system settings. ASSIGN1–8Make “assign” settings. By using the assign settings, you can control other parameters at the same time as the specified functions when you operate the RC-500’s switches/knobs or a footswitch or expression pedal connected to the CTL 1, 2/EXP jack. You can also make settings to control the RC-500 from an external MIDI device. Eight assign settings can be specified for each memory. NAMESpecifies the memory name. * Maximum of 12 characters
1. Select the memory that you want to edit.
2. Press the [MEMORY] button. The memory settings screen appears.

MEMORY

REC J

3. Turn the [MEMORY/VALUE] knob to select the item that you want to edit, and press the [MEMORY/VALUE] knob.

J

LOOP FX

OFF

4. Turn the [MEMORY/VALUE] knob to select the parameter that you want to edit, and press the [MEMORY/VALUE] knob.

TYPE

REPEAT1 J

5. Turn the [MEMORY/VALUE] knob to change the value.
6. Press the [MEMORY] button to return to the play screen.
7. If you want to save the edited settings, execute the Write operation (p. 10).

Item · Parameter · Value

Page 13 of the Boss Loop Station user manual — MEMO
Page 13 · click to enlarge
Page 13

Editing a Memory

Using the Loop FX

Specifying the Function of the Switches

By applying the loop FX, you can change how the loop plays back.

As appropriate for your method of use, you can assign other functions to the [REC/PLAY], [STOP], and [TRACK SELECT] switches.

1. In step 3 of p. 12, select “LOOP FX” and then press the [MEMORY/VALUE] knob.

As an example, here’s how to assign the following functions to these switches.

2. Press the [MEMORY/VALUE] knob, then turn the [MEMORY/VALUE] knob to select “ON,” and then press the [MEMORY/VALUE] knob.

[REC/PLAY] Track 1 record/play/stop (clear)

[STOP] Track 2 record/play/stop (clear)

3. Turn the [MEMORY/VALUE] knob to select “TYPE,” and press the [MEMORY/VALUE] knob.

[TRACK SELECT] Loop FX On/Off

1. In step 3 of p. 12, select “CONTROL” and then press the [MEMORY/VALUE] knob.

TYPE

REPEAT1 J

2. Turn the [MEMORY/VALUE] knob to select one of “PDL 1 FUNC” to “PDL 3 FUNC,” and press the [MEMORY/VALUE] knob.
4. Turn the [MEMORY/VALUE] knob to set the type.

PDL 1 FUNC

5. Press the [MEMORY] button to return to the play screen.

T1 REC/PLY J

6. If you want to save the edited settings, execute the Write operation (p. 10).
3. Turn the [MEMORY/VALUE] knob to make the following settings.

REPEAT1–3 Plays the track repeatedly in time with the beat.

PDL 1 FUNC T1 R/P/S(C

PDL 2 FUNC T2 R/P/S(C

SHIFT1–2 The track will play shifted by the length of the beat.

PDL 3 FUNC LOOP FX

SCATTER1–4 The track will be scrubbed in time with the beat.

4. Press the [MEMORY] button to return to the play screen.

VINYL FLICK The track will sound as though you are touching the turntable.

The functions assigned to each switch can be saved and used as “system” settings (one for the entire unit) or as “memory” settings (individual memories).

MEMO

The function of turning loop FX on/off can be assigned to the [REC/PLAY], [STOP], or [TRACK SELECT] switch.

To save and use the assignments as system settings: In the system settings (p. 16), set PREF/PDL1–3 PREF to “SYSTEM.” There is no need to execute the Write operation.

To save and use the assignments as memory settings: In the system settings, set PREF/PDL1–3 PREF to “MEMORY.” Execute the Write operation to save the settings in a memory.

Switch Function · Type Explanation · Parameter Value

Page 14 of the Boss Loop Station user manual — 50 J
Page 14 · click to enlarge
Page 14

Editing a Memory

Editing the Rhythm Settings

For details on the parameters, refer to “Parameter Guide” (PDF).

* Rhythm parameters can also be edited from the edit screens for a memory.

LEVEL Adjusts the volume of the rhythm sound.

REVERB Specifies the depth of the reverb that is applied to the rhythm.

1. Select the memory for which you want to edit the rhythm settings.

PATTERN Selects the rhythm pattern.

VARIATION Selects the rhythm pattern variation.

VAR.CHANGE Specifies the timing at which the rhythm

2. Long press the RHYTHM [ON/OFF] button. The rhythm settings screen appears.

pattern’s variation is changed.

KIT Selects the drum kit used to play the rhythm.

J

LEVEL

BEAT Specifies the time signature of the rhythm.

START Specifies how rhythm playback starts.

3. Turn the [MEMORY/VALUE] knob to select the parameter that you want to edit, and press the [MEMORY/VALUE] knob.

STOP Specifies how rhythm playback stops.

REC COUNT Specifies whether a count-in is heard for recording.

REVERB

PLAY COUNT Specifies whether a count-in is heard for playback.

50 J

FILL Specifies whether the rhythm plays with a fill-in or without a fill-in.

4. Turn the [MEMORY/VALUE] knob to change the value, and press the [MEMORY/VALUE] knob.

PART1–4 Specify individually whether each drum sound of the selected drum kit is heard.

TONE LOW Adjusts the tonal character of the rhythm sound. TONE HIGH

5. Repeat steps 3–4 to edit the parameter that you want.
6. Long press the RHYTHM [ON/OFF] button, or press the [EXIT] button to return to the play screen.
7. If you want to save the edited settings, execute the Write operation (p. 10).

Parameter Expalnation · Parameter · Value

Page 15 of the Boss Loop Station user manual — REC END
Page 15 · click to enlarge
Page 15

Editing a Memory

Changing How the Rhythm Starts and Stops

As appropriate for your recording method or the phrase that you’re recording, you can change the way in which the rhythm starts and stops.

1. In step 3 of p. 14, select “START” and then press the [MEMORY/VALUE] knob.

START

LOOP START J

2. Turn the [MEMORY/VALUE] knob to specify how the rhythm starts, and then press the [MEMORY/ VALUE] knob.
3. Turn the [MEMORY/VALUE] knob to select “STOP,” and press the [MEMORY/VALUE] knob. STOP

LOOP STOP J

4. Turn the [MEMORY/VALUE] knob to specify how the rhythm stops, and then press the [MEMORY/ VALUE] knob.
5. Long press the RHYTHM [ON/OFF] button, or press the [EXIT] button to return to the play screen.
6. If you want to save the edited settings, execute the Write operation (p. 10).

START

LOOP START The rhythm plays when loop recording or playback starts.

The rhythm plays when loop recording ends and switches to playback.

REC END

This is useful if you want to perform without specifying a tempo, then start recording, and then play the loop in time with the rhythm when playback starts.

The rhythm plays before loop recording or playback. The rhythm starts playing when you press the switch once, and recording/playback starts in time with the rhythm when you press the switch once again.

BEFORE LOOP

STOP

The rhythm always continues playing.

OFF

If you are performing in synchronization with an external MIDI device, you can keep the rhythm playing continuously to allow synchronized playback.

LOOP STOP The rhythm stops when the loop stops.

The rhythm stops when loop recording ends. This is useful when you want to use the rhythm as a guide during recording.

REC END

Parameter Explanation

Page 16 of the Boss Loop Station user manual — F.RESET
Page 16 · click to enlarge
Page 16

Settings for the Entire RC-500

System Settings

For details on the parameters, refer to “Parameter Guide” (PDF).

DISP CONT

Adjusts the display contrast.

1. Press the [MENU] button. The SETUP screen appears.

DISP MODE

Specify what is shown in the screen during recording, playback, and overdubbing.

SETUP

GENERAL J

* If you use the unit with High Brightness mode turned on, we recommend that you use an alkaline battery.

GENERAL

2. Turn the [MEMORY/VALUE] knob to select the item that you want to edit, and press the [MEMORY/VALUE] knob.

UNDO/REDO

Specifies whether Undo/Redo is executed while you hold down the switch, or the instant that you take your foot off the switch.

J

DISP MODE

LOOP

PDL1–3 PREF, CTL1–2 PREF, EXP PREF

3. Turn the [MEMORY/VALUE] knob to select the parameter that you want to edit, and press the [MEMORY/VALUE] knob.

Selects whether the [REC/PLAY] switch, [STOP] switch, [TRACK SELECT] switch, and a footswitch or expression pedal connected to the CTL 1, 2/EXP jack perform the functions specified by each memory or the functions specified by the system settings.

PREFERENCE

DISP CONT

5 J

Refer to “Controlling Devices via MIDI” (p. 20).

MIDI

4. Turn the [MEMORY/VALUE] knob to change the value.

EXT1–5 MIN, EXT1–5 MAX

5. Press the [MENU] button to return to the play screen.

Specifies the extent (lower limit and upper limit) in which memories can be switched. You can create five types of settings.

EXTENT

Refer to “Connecting a Computer via USB” (p. 18)

STORAGE

Returns the RC-500 to its factory-set state (p. 25).

F.RESET

Show 4 more labels / short text on this page
Item Parameter/Explanation · Item · Parameter · Value
Page 17 of the Boss Loop Station user manual — PEAK SRC
Page 17 · click to enlarge
Page 17

Settings for the Entire RC-500

Input/Output Settings

Here’s how to make settings such as phantom power on/off, and settings related to the input and output jacks.

For details on the parameters, refer to “Parameter Guide” (PDF).

Turns phantom power on/off.

PHANTOM

1. Press the [INPUT] button. The editing screen for input/output settings appears.

J

PHANTOM

Specifies the output destination of the audio that is input to the MIC IN jack.

OFF

MIC IN

Specifies the output destination of the instrumental sound that is input to the INST IN (A/MONO, B) jacks.

INST IN

2. Turn the [MEMORY/VALUE] knob to select the parameter that you want to edit, and press the [MEMORY/VALUE] knob.

Specifies the output destination of the rhythm sound.

RHYTHM

MIC IN

OUT-A&B J

Specifies the depth of the noise suppressor that’s applied to the audio input from the MIC IN jack.

MIC IN NS

3. Turn the [MEMORY/VALUE] knob to change the value, and press the [MEMORY/VALUE] knob.

Specifies the depth of the noise suppressor that’s applied to the instrumental sound input from the INST IN (A/MONO, B) jacks.

INST IN NS

4. Repeat steps 2–3 to edit the parameter that you want.

Specifies the input/output that is shown by the INPUT indicator.

PEAK SRC

5. Press the [INPUT] or [EXIT] button to return to the play screen.

Parameter Explanation · Parameter · Value

Page 18 of the Boss Loop Station user manual — NOTE
Page 18 · click to enlarge
Page 18

Connecting a Computer via USB

If the RC-500 is connected via USB to your computer, you’ll be able to do the following.

5 Back up the RC-500’s data to your computer.

5 Restore (recover) backed-up data from your computer to the RC-500.

5 Use BOSS TONE STUDIO to import or back-up loop phrases (audio files).

To use BOSS TONE STUDIO

Access the following URL, and download BOSS TONE STUDIO.

& https://www.boss.info/support/

Connecting the RC-500 and Computer

1. Use a commercially available USB cable to connect the RC-500’s O (USB) port to your computer’s USB port.
Boss Loop Station — Connecting the RC-500 and Computer diagram (page 18)
Fig. 17 · Connecting the RC-500 and Computer

NOTE

5 Use a USB cable that supports USB 2.0 Hi-Speed.

5 Do not use a micro USB cable that is designed only for charging a device. Charge-only cables cannot transmit data.

5 This might not work correctly for some models of computer. Refer to the BOSS website for details on the operating

systems that are supported.

Page 19 of the Boss Loop Station user manual — NOTE
Page 19 · click to enlarge
Page 19

Connecting a Computer via USB

Backing-Up or Recovering Data

1. Press the [MENU] button. The SETUP screen appears.
6. Back-up or recover the data.

SETUP

Backup

GENERAL J

Copy the entire “ROLAND” folder from the BOSS RC-500 drive to your computer.

2. Turn the [MEMORY/VALUE] knob to select “STORAGE,” and press the [MEMORY/VALUE] knob.

Recover

* When you execute this operation, the memory currently saved in the RC-500 disappears. Back up in advance.

STORAGE

OFF J

In the BOSS RC-500 drive, delete the “ROLAND” folder, and then copy the backed-up “ROLAND” folder from the computer into the BOSS RC-500 drive.

3. Turn the [MEMORY/VALUE] knob to set “PREPARING...”.
4. Use a USB cable to connect the RC-500’s USB port to your computer’s USB port. When a connection with the computer is established, the message “CONNECTING...” appears.

NOTE

Do not delete the folders in the BOSS RC-500 drive other than when executing the recovery operation.

* USB connection is not possible if the unit is not stopped, or if there is a phrase that has not been saved.

7. Eject the USB drive.

In the lower right of your screen, click the [

5. Open the BOSS RC-500 drive.

] icon, and then click “Eject BOSS RC-500.”

Within My Computer (or Computer), open “BOSS RC-500” (or Removable Disk).

Drag the “BOSS RC-500” icon to the trash (“Eject” icon).

On the desktop, open the “BOSS RC-500” icon.

Show 6 more labels / short text on this page
Windows · ] icon · 0 [ · Windows · Mac OS · Mac OS
Page 20 of the Boss Loop Station user manual — Controlling an External MIDI Device from the RC-500
Page 20 · click to enlarge
Page 20

Controlling Devices via MIDI

Connection

MIDI cables are connected to these connectors as needed.

MIDI IN Receives messages from another MIDI device. MIDI OUT Transmits messages from this device.

To make these connections, use TRS/MIDI connecting cables (sold separately: BMIDI-5-35).

MIDI Settings

Use of MIDI requires that the MIDI channels be matched with those of the connected device. Data cannot be transmitted to, nor received from another MIDI device unless the MIDI channels are set properly.

For details on each of the MIDI setting parameters, refer to “Parameter Guide” (PDF).

Controlling an External MIDI Device from the RC-500

Overview Explanation Transmitting tempo data and data for starting and stopping playback

Setting an external MIDI device to the same tempo as the RC-500 MIDI Clock messages are output from the RC-500 at all times. Set the external MIDI device beforehand so it is ready to receive MIDI Clock and MIDI Start and Stop messages.

The RC-500’s performance tempo data is transmitted to external MIDI devices as MIDI Clock.

For details, refer to the owner’s manual that came with the device.

Transmitting Start/Stop A MIDI Start message is transmitted at the moment that recording or playback of the track begins, when tracks had been stopped. This message is also transmitted when an All Start is carried out.

Playback start and stop operations with the RC-500’s switches can be transmitted as MIDI Start and Stop messages.

A MIDI Stop message is transmitted when tracks have stopped. This is also transmitted when All Stop is in carried out.

* If you want MIDI synchronized performance to continue even after the track stops, set the RHYTHM parameter STOP to “OFF.”

* Tracks whose 1SHOT setting (p. 11) is “ON” and tracks whose LOOP.S setting (p. 11) is “OFF” will not transmit Start/Stop data. Transmitting Program Change messages

Transmitting Program Change messages When memories are switched on the RC-500, a MIDI Program Change message is transmitted to the connected external MIDI device. You can transmit Program Change messages numbered 1 through 99, corresponding to the 99 individual memories 1–99.

When a memory is selected with the RC-500, a Program Change message corresponding to the selected memory number is transmitted simultaneously.

* Set “PC OUT” to ON beforehand.

* Program Change messages 100–128 cannot be transmitted.

* Bank Select MIDI messages (Control Change #0, #32) cannot be transmitted. Transmitting Control Change messages

Operating information for the RC-500’s switches, buttons, knobs, and an external expression pedal or footswitch is transmitted as Control Change messages.

Transmitting Control Change messages If you select a Control Change as the “ASSIGN” target, you can transmit MIDI Control Change messages by operating the RC-500’s switches, buttons, knobs, or an external footswitch or expression pedal (connected to the CTL 1, 2/EXP jack).

Connector Explanation

Page 21 of the Boss Loop Station user manual — MIDI OUT MIDI IN
Page 21 · click to enlarge
Page 21

Controlling Devices via MIDI

Controlling the RC-500 from an External MIDI Device

Overview Explanation Receiving tempo data and data for starting and stopping playback

Setting the RC-500 to the same tempo as an external MIDI device Make settings on your external MIDI device so that it will transmit MIDI Clock and MIDI Start/Stop data. For details, refer to the owner’s manual of your device.

The RC-500 will synchronize to the tempo of MIDI Clock data from an external MIDI device.

Set the RC-500’s MIDI SYNC to “AUTO.”

* You can’t switch the tempo during recording.

Receiving MIDI Start When MIDI Start (FA) is received, all tracks will play (All Start).

Start/stop data will be received from an external MIDI device to play/stop the RC-500.

Switching memories You can switch the RC-500’s memories with Program change messages from external MIDI devices.

The RC-500’s memories switch simultaneously upon receipt of corresponding Program Change messages from external MIDI devices.

The RC-500 can receive program change messages numbered 1 through 99, corresponding to the 99 individual memories 1–99.

* Program Change messages 100–128 cannot be received.

* Even if received, Bank Select MIDI messages (Control Change #0, #32) are disregarded. Receiving Control Change messages

Receiving Control Change messages You can use Control Change messages from an external MIDI device to control functions that would be difficult to control using the RC-500’s own controllers.

The RC-500 can be controlled using Control Change messages from external MIDI devices.

As the “ASSIGN” setting, set SOURCE to “CC#1–#31 or CC#64–#95,” and as TARGET select the parameter that you want to control.

Connecting Two RC-500 Units

Two RC-500 units can be synchronized after connecting them together using a MIDI cable.

* To make this connection, use a stereo mini-plug , stereo mini-plug cable.

Begin recording on the master RC-500 unit’s tracks.

MIDI OUT MIDI IN

The slave RC-500 unit starts in synchronization when the master RC-500 unit’s track starts playing.

Tracks for which TEMPO.S is ON will play at the memory tempo of the master unit.

Tracks whose LOOP.S is ON will loop according to the first- recorded phrase on the master RC-500.

Master unit Slave unit

Switching memories

Page 22 of the Boss Loop Station user manual — Appendix
Page 22 · click to enlarge
Page 22

Appendix

Troubleshooting

Problem Items to Check Action

Is the RC-500 properly connected to other devices? Check the connections to other devices (p. 2).

Is the power to the connected amp or mixer not turned on, or is the volume turned down? Check the settings for connected devices.

Are the connection cables shorted? Try replacing the connection cable.

Could the [TRACK 1] slider, [TRACK 2] slider, or the [MIC LEVEL] knob be lowered? Adjust sliders/knob to the suitable positions.

Check the T1 LEVEL and T2 LEVEL settings (p. 11).

Are the track 1and 2 level set correctly?

Check whether an external expression pedal might have been used to adjust the level .

Are the track 1 and 2 audio output destinations set correctly? Check the T1 OUTPUT and T2 OUTPUT settings (p. 11).

Check the TRACK 1, 2 [EDIT] button to see whether the track has been recorded. If the TRACK 1, 2 [EDIT] button is lit blue, nothing has been recorded.

Has anything been recorded to the tracks?

Is RHYTHM LEVEL set correctly? Check the RHYTHM LEVEL setting (p. 14).

Is the output destination of the rhythm sound set correctly? In “Input/Output Settings” (p. 17), check the RHYTHM setting.

Sound is missing from the beginning and end of the recorded track

To prevent noise, a fade-in and a fade-out are applied at the beginning and end of a recording. In some cases, it may sound as if some of the sound has been left out.

Unable to hear sounds from device connected to INST IN jacks/ MIC IN connector

Could the [TRACK 1] slider, [TRACK 2] slider, or the [MIC LEVEL] knob be lowered? Adjust sliders/knob to the suitable positions.

Is the audio output destination set correctly? In “Input/Output Settings” (p. 17), check the MIC IN, INST IN, and RHYTHM settings.

Memories not switching Is something other than the Play screen appearing in the display?

You cannot switch memories while any screen other than the Play screen is displayed. Press the [EXIT] button to return to the Play screen.

Is there insufficient memory remaining? If memory is insufficient, clear any unneeded memories (p. 10) before recording or overdubbing.

Recording/overdubbing stops before finishing

When recording with Loop Sync set to ON, once the end of the longest track is reached, the RC-500 automatically switches to overdubbing.

Is LOOP.S (p. 11) set to “ON” in the track?

You cannot change the memory tempo during recording or overdubbing. Change the tempo while the performance is stopped or being played back.

Is recording or overdubbing in progress?

When TEMPO.S is not set to ON in a track, the playback speed does not change even if the memory tempo is changed.

Playback tempo not changing

Is TEMPO.S (p. 11) set to “ON” in the track?

To match the playback speed to the memory tempo, set the track’s TEMPO.S setting to “ON.”

If MIDI clock is being received via the MIDI IN connector or the USB port, the RC-500 will synchronize its tempo to MIDI clock.

Is the RC-500 synchronized via MIDI?

If you don’t want to synchronize with an external device, set SYNC to “INTERNAL.”

Show 4 more labels / short text on this page
Problems with sound · No sound/low volume · No rhythm sound · Problems with operation
Page 23 of the Boss Loop Station user manual — MEMORY FULL
Page 23 · click to enlarge
Page 23

Appendix

Problem Items to Check Action

Could there be a short in the MIDI cable? Try replacing the MIDI cable.

Is the external MIDI device properly connected? Check the connections to the external MIDI device.

MIDI messages not being transmitted/received

Are the MIDI channels matched to those of the external MIDI device? Confirm that both devices are set to the same MIDI channels.

If transmitting from the RC-500, have you made the necessary settings for transmission?

Check the TX CH (transmit channel) setting and the PC OUT (program change message transmit) on/off setting.

Is the USB cable properly connected? Check the connection (p. 18).

(If exchanging files via USB with your computer) Could “STORAGE” be OFF?

In the procedure “Backing-Up or Recovering Data,” set STORAGE to “PREPARING...”.

Unable to communicate with computer

Could you be editing a memory? USB connection is not possible if there is an unsaved memory.

Save the memory (p. 10), and then try USB connection again.

Error Message List

LOOPER

In the factory reset function (p. 25), choose “SYS+MEM” to return the RC-500 to its factory settings.

DATA DAMAGED Data may have been damaged.

DATA READ ERR A problem has occurred with the content of the RC-500’s memory. Consult your Roland dealer or local Roland Service. DATA WRITE ERR

DATA TOO LONG Playback is not possible because the recording time or audio file is too long.

The recording time or audio file length must not exceed 1.5 hours.

DATA TOO SHORT Playback is not possible because the recording time or audio file is too short.

The recording time or audio file length must be at least 0.1 seconds.

EVENT FULL Further overdubbing is not possible. Save the memory (p. 10).

No further recording is possible on the current track.

The recorded time of one track exceeded 1.5 hours (approximately).

Save the memory (p. 10). If you want to continue recording, select a different memory.

MEMORY FULL

The total recording time of all memories exceeded 13 hours (approximately).

Clear unneeded memories (p. 10).

No further recording is possible.

NOT EMPTY You are attempting to overwrite-save onto a memory in which a phrase is already recorded.

Either clear the currently selected memory (p. 10), or select an empty memory.

TEMPO TOO FAST Since the track is being played at a much faster tempo than when it was recorded, it might not play back correctly.

Adjust the tempo.

TEMPO TOO SLOW Since the track is being played at a much slower tempo than when it was recorded, it might not play back correctly.

Problems with USB · Message Meaning Action

Page 24 of the Boss Loop Station user manual — STOP ALL&SAVE
Page 24 · click to enlarge
Page 24

Appendix

Lower the performance tempo.

The RC-500 could not process the data completely.

In the case of “TOO BUSY OMSG,” return to the tempo that was used during recording.

TOO BUSY

For “TOO BUSY OMSG”: Since you attempted to apply the loop FX to a phrase that was set to a significantly slower tempo than when it was recorded, the data could not be processed quickly enough.

Save the current content to a memory.

TOO BUSY OMSG

If this appears frequently, back up the data to your computer, then execute factory reset “SYS+MEM,” and then recover the data (p. 19, p. 25).

UNDEFINED ERR An error of unknown cause has occurred during recording, playback, or overdubbing. Consult your Roland dealer or local Roland Service.

MIDI

BUFFER FULL An excessive volume of messages were received and could not be processed properly.

Reduce the number or size of MIDI messages transmitted to the RC-500.

OFFLINE There is a problem with the MIDI cable connection. Check to make sure the cable has not been disconnected and that there is no short in the cable.

BATTERY LOW The battery has run down.

Because the battery has run down, the unit cannot function correctly.

Replace the batteries, or use an AC adaptor. BATTERY LOW!! STOP ALL

All operations of the RC-500 have stopped.

MEMORY FULL This unit’s memory is insufficient. If this message appears, recording or overdubbing might end mid-way.

Clear unneeded memories (p. 10), and then try recording again.

STOP LOOPER The operation is not possible during recording, playback, or overdubbing. Stop before performing the operation.

STOP ALL The operation is not possible during recording, playback, overdubbing, or rhythm playback. Stop all of these before performing the operation.

The operation is not possible during recording, playback, overdubbing, or rhythm playback when there is also unsaved data.

STOP ALL&SAVE

Stop all of these, and then save the memory (p. 10).

Check the format of the audio file.

UNSUPPORTED FILE This audio file is unplayable.

To import an audio file into the RC-500, use “BOSS TONE STUDIO.”

Message Meaning Action · Others

Page 25 of the Boss Loop Station user manual — MEMORY J
Page 25 · click to enlarge
Page 25

Appendix

Restoring the Factory Default Settings (Factory Reset)

Not only can you return all of the settings to the values in effect when the RC-500 was shipped from the factory, you can also specify the items to be reset.

* When you execute “Factory Reset,” the settings you made will be lost. In advance, back up important data to your computer.

1. Press the [MENU] button. The SETUP screen appears.
4. Turn the [MEMORY/VALUE] knob to select “OK,” and press the [MEMORY/VALUE] knob. The factory reset is executed.

SETUP

* Do not turn off the power while the “EXECUTING...” message is shown.

GENERAL J

2. Turn the [MEMORY/VALUE] knob to select “F.RESET,” and press the [MEMORY/VALUE] knob.

Once the factory reset is complete, you are returned to the Play screen.

F.RESET

MEMORY J

3. Turn the [MEMORY/VALUE] knob to specify the settings that will be returned to their factoryset state, and press the [MEMORY/VALUE] knob.

MEM+SYS Memory 1–99 and system settings

A confirmation message “ARE YOU OK?” appears.

* If you decide not to execute the factory reset, select “CANCEL” and press the [MEMORY/VALUE] knob.

Value Explanation · MEMORY Memory 1–99 · SYSTEM System settings

Page 26 of the Boss Loop Station user manual — Appendix
Page 26 · click to enlarge
Page 26

Appendix

Main Specifications

Sampling Frequency 44.1 kHz

AD/DA Conversion 32 bits

Processing 32-bit floating point

Number of Tracks: 2 Data Format: WAV (44.1 kHz, 32-bit float, stereo) Approx. 1.5 hours (1 track), Approx.13 hours (total of all memories)

Rhythm Type 57 Patterns x 2 Variations

Rhythm Kit 16 types

LOOP FX (only for loop tracks) Type: BEAT REPEAT, BEAT SHIFT, BEAT SCATTER, VINYL FLICK

Reverb (only for rhythm part)

Nominal Input Level MIC IN:-40 dBu (variable) INST IN A/MONO, B: -10 dBu

Maximum Input Level MIC IN:+8 dBu INST IN A/MONO, B: +8 dBu

Input Impedance MIC IN4 kΩ INST IN A/MONO, B: 1 MΩ

Nominal Output Level OUTPUT A/MONO, B: -10 dBu

Maximum Output Level OUTPUT A/MONO, B: +8 dBu

Output Impedance OUTPUT A/MONO, B1 kΩ

Recommended Load Impedance OUTPUT A/MONO, B: 10 kΩ or greater

Display Graphic LCD (96 x 32 dots, RGB backlit LCD)

INST IN A/MONO, B jacks: 1/4-inch phone type MIC IN jack: XLR type (balanced, phantom power: DC 48 V, 10 mA Max OUTPUT A/MONO, B jacks: 1/4-inch phone type CTL 1,2/EXP jack: 1/4-inch TRS phone type USB port: USB micro B type MIDI (IN, OUT) jacks: stereo miniature type DC IN jack

Power Supply Alkaline battery (AA, LR6) x 4 AC adaptor (PSA series: sold separately)

Current Draw 330 mA (with phantom power) 240 mA (without phantom power)

Expected battery life under continuous use

* These figures will vary depending on the actual conditions of use. Alkaline: Approx. 3.5 hours (without phantom power), Approx. 2 hours (with phantom power)

(excluding rubber foot) 170 (W) x 138 (D) x 60 (H) mm 6-3/4 (W) x 5-7/16 (D) x 2-3/8 (H) inches

(including rubber foot) 170 (W) x 138 (D) x 62 (H) mm 6-3/4 (W) x 5-7/16 (D) x 2-1/2 (H) inches

Weight (including battery) 950 g 2.1 lbs

Accessories Owner’s Manual, Leaflet “USING THE UNIT SAFELY,” AC adaptor, Rubber foot x 4

AC adaptor: PSA-S series Footswitch: FS-5U Dual Footswitch: FS-6, FS-7 Expression Pedal: FV-500H, FV-500L, EV-30, Roland EV-5 TRS/MIDI connecting cable: BMIDI-5-35

* 0 dBu = 0.775 Vrms

* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

Show 7 more labels / short text on this page
Recording/Playback · Effect · Memory 99 · Bypass Buffered bypass · Connectors · Dimensions · Options (sold separately)
Page 27 of the Boss Loop Station user manual — Intellectual Property Right
Page 27 · click to enlarge
Page 27

USING THE UNIT SAFELY

CAUTION

CAUTION

Keep small items out of the reach of children To prevent accidental ingestion of the parts listed below, always keep them out of the reach of small children. • Included Parts Rubber feet (p. 2)

Precautions concerning use of phantom power supply Always turn the phantom power off when connecting any device other than condenser microphones that require phantom power. You risk causing damage if you mistakenly supply phantom power to dynamic microphones, audio playback devices, or other devices that don’t require such power. Be sure to check the specifications of any microphone you intend to use by referring to the manual that came with it. (This instrument’s phantom power: 48 V DC, 10 mA Max)

IMPORTANT NOTES

Power Supply: Use of Batteries

Additional Precautions

  • The copyright of content in this product (the sound waveform data, style data, accompaniment patterns, phrase data, audio loops and image data) is reserved by Roland Corporation.
  • Purchasers of this product are permitted to utilize said content (except song data such as Demo Songs) for the creating, performing, recording and distributing original musical works.
  • Purchasers of this product are NOT permitted to extract said content in original or modified form, for the purpose of distributing recorded medium of said content or making them available on a computer network.
  • This product contains eParts integrated software platform of eSOL Co., Ltd. eParts is a trademark of eSOL Co., Ltd. in Japan.
  • This product includes third party open source software.
  • Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.
  • If operating this unit on batteries, please use alkaline batteries.
  • Even if batteries are installed, the unit will turn off if you connect or disconnect the power cord from the AC outlet while the unit is turned on, or if you connect or disconnect the AC adaptor from the unit. When this occurs, unsaved data may be lost. You must turn off the power before you connect or disconnect the power cord or AC adaptor.
  • Any data stored within the unit can be lost as the result of equipment failure, incorrect operation, etc. To protect yourself against the irretrievable loss of data, try to make a habit of creating regular backups of the data you’ve stored in the unit.
  • Roland assumes no liability concerning the restoration of any stored content that has been lost.
  • Never strike or apply strong pressure to the display.
  • When disposing of the packing carton or cushioning material in which this unit was packed, you must observe the waste disposal regulations that apply to your locality.
  • Do not use connection cables that contain a built-in resistor.

Repairs and Data

  • Before sending the unit away for repairs, be sure to make a backup of the data stored within it; or you may prefer to write down the needed information. Although we will do our utmost to preserve the data stored in your unit when we carry out repairs, in some cases, such as when the memory section is physically damaged, restoration of the stored content may be impossible. Roland assumes no liability concerning the restoration of any stored content that has been lost.

Copyright © 2009-2019 ARM Limited. All rights reserved.

Intellectual Property Right

Licensed under the Apache License, Version 2.0 (the “License”);

  • It is forbidden by law to make an audio recording, video recording, copy or revision of a third party’s copyrighted work (musical work, video work, broadcast, live performance, or other work), whether in whole or in part, and distribute, sell, lease, perform or broadcast it without the permission of the copyright owner.
  • Do not use this product for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this product.

You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Copyright © 2016, Freescale Semiconductor, Inc.

All rights reserved.

Licensed under the BSD-3-Clause

You may obtain a copy of the License at

  • <a href="https://opensource.org/licenses/BSD-3-Clause" rel="nofollow noopener" target="_blank">https://opensource.org/licenses/BSD-3-Clause</a>
  • Roland, BOSS, and LOOP STATION are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
  • Company names and product names appearing in this document are registered trademarks or trademarks of their respective owners.

Copyright 2016-2019 NXP

Page 28 of the Boss Loop Station user manual — USING THE UNIT SAFELY
Page 28 · click to enlarge
Page 28
Page 28 of the Boss Loop Station user manual — USING THE UNIT SAFELY
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Display codes

Error codes

What the fault codes shown on the display mean and how to clear them.

CodeMeaningFix
RC-500. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 p.1
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Problems with sound p.22
No sound/low volumeIs the RC-500 properly connected to other devices? p.22
No sound/low volumeIs the power to the connected amp or mixer not turned on, or is the volume turned down? p.22
No sound/low volumeAre the connection cables shorted? p.22
No sound/low volumeCould the [TRACK 1] slider, [TRACK 2] slider, or the [MIC LEVEL] knob be lowered? p.22
No sound/low volumeAre the track 1and 2 level set correctly? p.22
No sound/low volumeAre the track 1 and 2 audio output destinations set correctly? p.22
No sound/low volumeHas anything been recorded to the tracks? p.22
No rhythm soundIs RHYTHM LEVEL set correctly? p.22
No rhythm soundIs the output destination of the rhythm sound set correctly? p.22
Sound is missing from the beginning and end of the recorded trackTo prevent noise, a fade-in and a fade-out are applied at the beginning and end of a recording. In some cases, it may sound as if some of the sound has been left out. p.22
Unable to hear sounds from device connected to INST IN jacks/ MIC IN connectorCould the [TRACK 1] slider, [TRACK 2] slider, or the [MIC LEVEL] knob be lowered? p.22
Unable to hear sounds from device connected to INST IN jacks/ MIC IN connectorIs the audio output destination set correctly? p.22
Problems with operation p.22
Memories not switchingIs something other than the Play screen appearing in the display? p.22
Recording/overdubbing stops before finishingIs there insufficient memory remaining? p.22
Recording/overdubbing stops before finishingIs LOOP.S (p. 11) set to “ON” in the track? p.22
Playback tempo not changingIs recording or overdubbing in progress? p.22
Playback tempo not changingIs TEMPO.S (p. 11) set to “ON” in the track? p.22
Playback tempo not changingIs the RC-500 synchronized via MIDI? p.22
MIDI messages not being transmitted/receivedCould there be a short in the MIDI cable? p.23
MIDI messages not being transmitted/receivedIs the external MIDI device properly connected? p.23
MIDI messages not being transmitted/receivedAre the MIDI channels matched to those of the external MIDI device? p.23
MIDI messages not being transmitted/receivedIf transmitting from the RC-500, have you made the necessary settings for transmission? p.23
Problems with USB p.23
Unable to communicate with computerIs the USB cable properly connected? p.23
Unable to communicate with computer(If exchanging files via USB with your computer) Could “STORAGE” be OFF? p.23
Unable to communicate with computerCould you be editing a memory? p.23

Ask about the Boss Loop Station

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Boss Loop Station

Be the first to ask — other owners or our team will answer.

Original document

Boss Loop Station manual PDF

28 pages·635 KB·Guitar Pedal·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…