EN
Official user manual

POLYCOOL Ice Maker

9 pages·257 KB·Ice Maker·PDF·ENDEFRITNLJA
POLYCOOL Ice Maker
Table of Contents 11 sections User Manual · Safety · Before First Use · Parts Identification · … ShowHide
Page 1 of the POLYCOOL Ice Maker user manual — User Manual
Page 1 · click to enlarge
Page 1
POLYCOOL Ice Maker — User Manual diagram (page 1)
Fig. 1 · User Manual
POLYCOOL Ice Maker — User Manual diagram (page 1)
Fig. 2 · User Manual

User Manual

[Revision 2.0 May 2017]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

  • DAMAGE AND MAY VOID WARRANTY.
  • KEEP THIS MANUAL FOR FUTURE REFERENCE .
  • Products covered by this

manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Page 2 of the POLYCOOL Ice Maker user manual — Before First Use
Page 2 · click to enlarge
Page 2

Safety

When using electrical appliances, basic safety precautions should always be followed, including the following:

  • Electric shock/electrocution hazard - NEVER immerse the electrical cord or appliance body in water.
  • Indoor use only - do not use outdoors.
  • The appliance must be used on flat, level surfaces only.
  • Some surfaces of the appliance may become hot during use (especially the cooling system components).
  • Allow at least 150mm (6") of clearance around the appliance and do not use the appliance near sources of

heat (ovens etc).

  • It is recommended to use only bottled, filtered or tap water that is suitable for drinking. Do not use any

other type of liquid, such as fruit juice.

  • Do not use water that has remained in the appliance for a period of time – it is recommended to always use

fresh water at each use.

  • Unplug from the electrical supply while not in use, when assembling and before cleaning.
  • Supervision is necessary when using the appliance near children.
  • Do not allow children to operate or play with the appliance.
  • Lift/carry the unit by holding the body with both hands. Do not allow the unit to tilt >45° when being moved

or transported, otherwise, damage to the compressor may result.

  • Do not use the unit if it causes a circuit breaker to trip – have it inspected and repaired at an authorized

service center or by a qualified technician. Never try to replace parts or repair the unit by yourself.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge. All users should have adequate training in safely

operating the product or be under supervision of a person responsible for their safety

  • Do not operate the appliance if the cord or plug is damaged.
  • This appliance is for domestic use only.

Before First Use

  • Check that the voltage indicated on the rating label corresponds to the mains voltage.
  • Thoroughly clean all parts except the body in warm soapy water, then rinse and dry.
  • Place the appliance where it is to be used, open all covers and allow to stand for a minimum of 2 hours

before connecting to power

Page 3 of the POLYCOOL Ice Maker user manual — Safety
Page 3 · click to enlarge
Page 3
Page 3 of the POLYCOOL Ice Maker user manual — Safety
Page 4 of the POLYCOOL Ice Maker user manual — Parts Identification
Page 4 · click to enlarge
Page 4

Parts Identification

POLYCOOL Ice Maker — Parts Identification diagram (page 4)
Fig. 3 · Parts Identification
POLYCOOL Ice Maker — Parts Identification diagram (page 4)
Fig. 4 · Parts Identification
POLYCOOL Ice Maker — Parts Identification diagram (page 4)
Fig. 5 · Parts Identification
POLYCOOL Ice Maker — Parts Identification diagram (page 4)
Fig. 6 · Parts Identification
POLYCOOL Ice Maker — Parts Identification diagram (page 4)
Fig. 7 · Parts Identification

No. Name No. Name

1 Body 3 Control Panel

2 Ice / Water Reservoir Cover 4 Drain Port

Page 5 of the POLYCOOL Ice Maker user manual — Console and Functions
Page 5 · click to enlarge
Page 5

Operation

Water Filling

It is recommended to use only bottled, filtered or tap water that is suitable for drinking. Do not

use any other type of liquid, such as fruit juice. • Do not use water that has remained in the

appliance for a period of time – it is recommended to always use fresh water at each use.

1. Disconnect the appliance from the mains electrical supply.
POLYCOOL Ice Maker — Operation diagram (page 5)
Fig. 8 · Operation
2. Open the ice / water reservoir cover ( A ).

A

POLYCOOL Ice Maker — A diagram (page 5)
Fig. 9

B

3. Use a suitable container to fill the water reservoir to just beneath

the ice tray (B).

4. Close the water reservoir cover and reconnect the appliance to the

mains electrical supply.

Console and Functions

The appliance features a display that provides you with information, such as current function, when more

water is required etc, The console activates as soon as the appliance is connected to the electrical supply.

POLYCOOL Ice Maker — Console and Functions diagram (page 5)
Fig. 10 · Console and Functions

START Press to switch the appliance ON and begin making ice.

STOP Press to switch the appliance OFF.

SELECT Press to select the required ice cube size. The lamp next to the "size" icons illuminates to show the

current selection. Note that larger cubes take longer to produce, however, also melt at a slower

rate. For higher ambient temperatures, large is recommended.

ADD WATER Illuminates if the water reservoir empty – add water to the machine. Machine may also beep.

ICE FULL Illuminates if the ice reservoir is full. When full, no more ice is produced. Machine may also beep.

Control Description

Page 6 of the POLYCOOL Ice Maker user manual — Care and Maintenance
Page 6 · click to enlarge
Page 6

Making Ice

If ice is made and left in the appliance, it may eventually melt – when melted, the water returns to the

water reservoir. Be careful to avoid overflow from the water reservoir due to melted ice adding to the

  • current reservoir contents.
  • Ensure that adequate water is in the w ater reservoir when making ice .
  • It takes

several minutes to create each batch of ice cubes, and this is also affected by the ambient temperature – do

not expect instant ice to be available. To monitor ice production, view it through the "window" in the ice / water

reservoir cover – do not allow the cover to remain open, and close it as soon as possible in order to retain

ice-cold temperatures in the ice reservoir. • Note that the size of the ice cubes may vary for the first few ice

making cycles.

Switch the ice making function ON using the START button. When on, the appliance draws water up from the

water reservoir into the cooling unit, creates the ice, drains excess water back into the water reservoir, then

moves the ice into the ice collection tray. Use the supplied scoop to collect the ice.

POLYCOOL Ice Maker — Making Ice diagram (page 6)
Fig. 11 · Making Ice

This image shows water in the

ice making tray and ice forming

on the cooling elements. When

the ice cubes are ready, the

remaining water is returned to

the water reservoir, the ice drops

from the cooling elements and is

shifted to the ice reservoir by a

"comb".

Care and Maintenance

  • After use, drain the appliance by removing the drain cap on the rear of the unit until no water remains.

Re-install drain cap and open reservoir covers approximately halfway and leave open. This helps

thoroughly dry the inside of the appliance and helps prevent corrosion of surfaces.

  • After each use, clean the inside of the appliance with a cloth and a solution of water and a small amount of

vinegar. Do not use detergents, solvents or chemicals.

  • When the appliance is in use, ensure that the reservoir cover is fully closed.
  • Regularly remove any accumulated dust from the air vents and cooling holes in the body of the machine.
  • If required, clean the appliance body with a damp cloth. Do not use detergents, solvents or chemicals.
Page 7 of the POLYCOOL Ice Maker user manual — Troubleshooting
Page 7 · click to enlarge
Page 7

Troubleshooting

Some maintenance activities described may be beyond the scope of some users. For procedures

that you are not comfortable with or have the tools or experience for, have the unit serviced by a

service centre or qualified technician.

The following information may assist in identifying a problem and rectifying it.

Ice not being produced.

P L L O Possible Fault O L OO O C L O O C O Y Action O O C C O L Y Y C O L O O C O Y No electrical supply C L Y OCheck that mains electricity is available and the appliance is properly connected to it. L Y C P O L Y O L Y P O P O L L P

No water Press STOP button. Add adequate water to water reservoir. Wait 3 minutes, then restart the

ice making function (press START button).

Ice collection tray full Remove ice from the tray to allow appliance to produce ice.

Air in water system Remove the drain cap from rear of appliance and allow several drops of water to escape

before re-installing the cap.

Ambient temperature too high Operate unit in a cooler area. Ensure that heat sources (ovens etc) are at least 150mm (6")

away from the appliance.

Cooling or control unit faulty Have appliance inspected and repaired by an authorised service centre or technician.

Ice sticking together.

L P O O P Possible Fault P LAction O L L P O O L O L C O C O L O O Ambient temperature or temperature C O Y C L of water in reservoir too low L Y O O L PO C Y Operate in a warmer area. Y C Y C O O L Y L Y C P O L O L Y P L P O P L O P L O
POLYCOOL Ice Maker — Troubleshooting diagram (page 7)
Fig. 12 · Troubleshooting

ICE FULL and ADD WATER indicators on at same time.

Y O L L P O Possible Fault O PP O L Action L L P O L O L O L L O L Ice shifting "comb" blocked O O C C O Y Y C L L Y O O L PO O C A build-up of ice may be preventing the "comb" from moving. Press STOP button. Gently move the comb slightly, and check that the machine is horizontal. Wait 3 minutes, then restart the ice O L Y C O O P O L Y C O L Y C O P O L Y P O L Y C L P O L O P L O making function (press START button). L O
POLYCOOL Ice Maker — Troubleshooting diagram (page 7)
Fig. 13 · Troubleshooting

Compressor unit noisy / buzzing.

O Y C C L Y Possible Fault Y O L OO L L Y P O O P Action P O P L P L O L L P P Input voltage fault L O L OCheck input voltage to appliance and ensure it is compatible. O L O L C O L Y C O C O O L Y
Page 8 of the POLYCOOL Ice Maker user manual — Specifications
Page 8 · click to enlarge
Page 8

Specifications

Input Voltage 240VAC / 50Hz

Water Reservoir Capacity 3.2l

O P L Ice Output Capacity O LPO L L O O O C O O 18 to 20kg per 24 hours O O C O Y C L Y OL O O O C O Refrigerant Agent Y CR134a L Y C L Y C O P O L Y O L Y C P O P O L

Dimensions 400mm (h) x 375mm (w) x 400mm (d)

Weight Approximately 13.5kg without liquids

Page 9 of the POLYCOOL Ice Maker user manual — Specifications
Page 9 · click to enlarge
Page 9

Some experts believe the incorrect or prolonged use of almost any product could cause serious

injury or death. For information that may reduce your risk of serious injury or death, consult the

points below and additionally, the information available at www.datastreamserver.com/safety

  • Consult all documentation, packaging and product
  • The product has been supplied by a general merchandise retailer that

labelling before use. Note that some products feature

may not be familiar with your specific application or your description of

online documentation which should be printed and kept

the application. Be sure to attain third-party approval for your application

with the product.

from a qualified specialist before use regardless of prior assurances by

  • Check product for loose / broken / damaged / missing

the retailer or its representatives.

parts, wear or leaks (if applicable) before each use.

  • This product is not intended for use where fail-safe operation is

Never use a product with loose / broken / damaged /

required. As with any product (take an automobile, aircraft, computer or

missing parts, wear or leaks (if applicable).

ball point pen for example), there is always a small chance of technical

  • Products must be inspected and serviced (if applicable)

issues that needs to be repaired or may require replacement of the

product or a part. If the possibility of such failure and the associated time

by a qualified specialist every 6 months assuming

average residential use by a person of average weight

it takes to rectify could in any situation inconvenience the user, business

and strength, above average technical aptitude, on a

or employee then the product is not suitable for your requirements. This

product is not for use where incorrect operation or a failure of any kind,

property matching average metropolitan specification.

Intended use outside these guidelines could indicate the

including but not limited to a condition requiring product return,

replacement, service by a technician or replacement of parts could

product is not suitable for intended use or may require

more regular inspection or servicing.

cause a financial loss, loss of employee time or an inconvenience

  • Ensure all possible users of the product have completed

requiring compensation.

  • If this item has been purchased in error after considering the points

an industry recognized training course before being given

above, simply contact the retailer directly for details of their returns

access to the product.

policy, if required.

©2017 Polycool. All rights reserved. No part of this document, including descriptive content, concepts, ideas,

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or mechanical,

including photocopying, scanning or recording, or any information storage and retrieval system, without

express permission or consent from the publisher.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
O O C O Y No electrical supply C L Y OCheck that mains electricity is available and the appliance is properly connected to it. L Y C P O L Y O L Y P O P O L L P p.7
O L O O Ambient temperature or temperature C O Y C L of water in reservoir too low L Y O O L PO C Y Operate in a warmer area. Y C Y C O O L Y L Y C P O L O L Y P L P O P L O P L O p.7
L O L Ice shifting "comb" blocked O O C C O Y Y C L L Y O O L PO O C A build-up of ice may be preventing the "comb" from moving. Press STOP button. Gently move the comb slightly, and check that the machine is horizontal. Wait 3 minutes, then restart the ice O L Y C O O P O L Y C O L Y C O P O L Y P O L Y C L P O L O P L O making function (press START button). L O p.7
L P P Input voltage fault L O L OCheck input voltage to appliance and ensure it is compatible. O L O L C O O O O L Y C O C O O L Y p.7

Ask about the POLYCOOL Ice Maker

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the POLYCOOL Ice Maker

Be the first to ask — other owners or our team will answer.

Original document

POLYCOOL Ice Maker manual PDF

9 pages·257 KB·Ice Maker·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…