EN
Official user manual

postmodular Crossover

1 pages·47 KB·Audio·PDF·ENDEFRITNLJA
postmodular Crossover
Table of Contents 15 sections A 6 · LR USER GUIDE · CROSSOVER · THE LR CIRCUIT 4 BLOCK DIAGRAM LR 4 · … ShowHide
Page 1 of the postmodular Crossover user manual — lasesentaysiete.com
Page 1 · click to enlarge
Page 1

A 6

LR USER GUIDE

CROSSOVER

postmodular Crossover — A 6 diagram (page 1)
Fig. 1

MID/HI knob sets the crossover point between the mid and high frequency bands.

postmodular Crossover — A 6 diagram (page 1)
Fig. 2

THE LR CIRCUIT 4 BLOCK DIAGRAM LR 4

MULTIBAND PROCESSING

postmodular Crossover — THE LR CIRCUIT 4 BLOCK DIAGRAM LR 4 diagram (page 1)
Fig. 3

The LR4 allows you to split a mono signal source into 3 separate frequency bands: low, mid, high. The crossover points between bands can be adjusted manually or by control voltage.

The LR4 Crossover comprises two state-variable filters in series. The high-pass from the first SVF gives the HI output, while the low-pass serves as the input to the second SVF. The high-pass of the second SVF gives the MID output, and the low-pass the LO output.

LO/MID knob sets the crossover point between the low and mid frequency bands.

SVF 1

postmodular Crossover — SVF 1 diagram (page 1)
Fig. 4

Think of the LR4 as the front end of a patchable multiband processor. Add varying amounts of compression to each band, or mix and match how you effect the lows, mids, and highs. You can even patch the outputs through VCAs for parametric amplitude modulation. Whatever multiband application you have in mind, the LR4 is designed impart a minimal sonic footprint, opening the door to further sonic sculpting.

INPUT

L/M CV attenuverter sets the gain and polarity of the L/M CV input.

It is possible for the crossover points of each filter to overlap, affecting adjacent frequency bands.

postmodular Crossover — INPUT diagram (page 1)
Fig. 5

M/H CV attenuverter sets the gain and polarity of the M/H CV input.

SVF 2

postmodular Crossover — SVF 2 diagram (page 1)
Fig. 6
postmodular Crossover — SVF 2 diagram (page 1)
Fig. 7

SVF 1 LP

IN audio input.

M/H CV input controls the mid/ high crossover frequency. Positive CV raises the crossover point, while negative CV lowers it. This input is normalled to the L/M CV input when not patched.

postmodular Crossover — SVF 1 LP diagram (page 1)
Fig. 8

HI output band as determined by the M/H crossover point.

Technical specifications

OUTPUTS

postmodular Crossover — OUTPUTS diagram (page 1)
Fig. 9

· 6hp · 25mm depth · 45mA/+12v, 45mA -12v current draw · reverse power polarity protection

postmodular Crossover — OUTPUTS diagram (page 1)
Fig. 10

MID output band as determined by the L/M & M/H crossover points.

LO MID HI

L/M CV input controls the low/ mid crossover frequency. Positive CV raises the crossover point, while negative CV lowers it.

postmodular Crossover — LO MID HI diagram (page 1)
Fig. 11

1 MID/HIGH CROSSOVER POINT

LO output band as determined by the L/M crossover point.

2 LOW/MID CROSSOVER POINT

The -12v supply line is indicated on the backside of the module NB:

lasesentaysiete.com

Ask about the postmodular Crossover

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the postmodular Crossover

Be the first to ask — other owners or our team will answer.

Original document

postmodular Crossover manual PDF

1 pages·47 KB·Audio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…