EN
Emerson logo
Official user manual

Emerson Wireless Module System

2 pages·638 KB·Communications·PDF·ENDEFRITNLJA
Emerson Wireless Module System
Table of Contents 5 sections Quick Setup Guide Emerson Wireless Module System and E2 · Setup and Commissioning of Module in E2 · Installing the Wireless Module · Module Commissioning Tips · … ShowHide
Page 1 of the Emerson Wireless Module System user manual — Installing the Wireless Module
Page 1 · click to enlarge
Page 1
Emerson Wireless Module System — Quick Setup Guide Emerson Wireless Module System and E2 diagram (page 1)
Fig. 1 · Quick Setup Guide Emerson Wireless Module System and…

Quick Setup Guide Emerson Wireless Module System and E2

For a copy of the full Wireless User Manual (P/N 026-1734), go to https://climate.emerson.com to download it or contact Emerson Electronics and Solutions Technical Support at 833-409-7505.

0-5V Input:

  • Humidity Sensor or Analog 0-5V Input
  • Pin 1 ON
  • Pin 2 OFF

Emerson’s Wireless Module System allows a quick and easy monitoring for a variety of Refrigeration and HVAC applications by connecting temperature probes, product simulators, humidity probes or switches to the Wireless Module that transmits these signals to the Wireless Gateway. The Gateway translates the signal into usable information to send to the building controller, E2 (version 4.08 or higher) or Supervisory controller, where the data can be logged into reports or used by algorithms to make control decisions. The Wireless Gateway can receive signals from up to 99 Modules. The Wireless Module is flexible and configurable with up to three (3) analog or digital inputs that can be used for a variety of applications in Refrigeration and HVAC, eliminating installation materials and costly labor-intensive wiring.

NTC/Dig Input:

  • Temp or Digital Sensor Input
  • Pin 1 OFF
  • Pin 2 ON

Table 1 - DIP Switch Settings

Setup and Commissioning of Module in E2

The Wireless Module must be associated with the Gateway through the Commissioning process. With proper range planning, all Modules can be commissioned to the Gateway prior to mounting. For complete instructions on setup and commissioning of the Wireless Module, refer to the Wireless User Manual (P/N 026-1734).

Installing the Wireless Module

Emerson Wireless Module System — Installing the Wireless Module diagram (page 1)
Fig. 2 · Installing the Wireless Module

Steps to set up and commission the Wireless Module in E2:

1. Go to the Add Application screen to add required number of RF Modules (Menu, 6, 1, F4: Lookup, 23. RF Module) then press Enter. 2. Enter how many (99 max per Gateway) and press Enter. 3. Once the RF Module application has been added, go to Configured Applications to commission the device (Menu, 5, 230. RF Module). 4. Select an RF Module from the list and press Enter. 5. Pull up the Actions Menu, and initiate commissioning (Enter, 9, 1: Commission Device). 6. The application will enter learning mode. 7. Within one (1) minute, press the Learn button on the Module.

Figure 1 - Wireless Module Board Inside Enclosure

If this is a User Selected Input Module (P/N 814-3600), you must set the DIP switch setting based on the input being received from the sensor; either 0 to 5V or NTC/Digital.

Emerson Wireless Module System — Installing the Wireless Module diagram (page 1)
Fig. 3 · Installing the Wireless Module
Emerson Wireless Module System — Installing the Wireless Module diagram (page 1)
Fig. 4 · Installing the Wireless Module
  • 814-3600 User selectable model:
  • Set only one switch ON for each sensor pair
  • Each pair can be set separately

Figure 2 - Wireless Module Enclosure

Document Part # 026-4255 Rev 3 Page 1 of 2 ©2021 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use. Visit our website at http://www.climate.emerson.com for the latest technical documentation and updates.

Page 2 of the Emerson Wireless Module System user manual — Wireless Module System Parts and Accessories
Page 2 · click to enlarge
Page 2

During the commissioning process, press the Learn button and the following occurs: Blue LED:

Module Commissioning Tips

  • Hours on battery is displayed in the Module Summary screen. The battery will last for 17,100 hours of use. The battery is still good if the voltage is 2.90 or higher.
  • It takes 200 lux five (5) hours per day to run the RF Module on the solar cell continuously.
  • Place Modules so that the solar cell can power the Module and battery usage indicator remains Off .
  • The default update rate of two (2) minutes optimizes power consumption.
  • Faster update rates may require an external 5V power supply (available as an option).
  • With proper range planning, all Modules can be commissioned to the Gateway with the Learn button prior to mounting.
  • Check signal strength on the E2 prior to mounting the Modules permanently.
  • Use the Test button for instant transmission if you do not want to wait for the regular update rate.
  • Placement of the Modules should be positioned so that SSI reception levels are 3 or 4 Bars. Reposition or use repeaters as necessary.
  • 1 blink = learning/commissioning started.
  • 2 blinks = commissioning was successful (occurs in one (1) second). 8. If successful, the Module Status will display Commissioned , then Good on the E2. Check signal strength prior to mounting the Modules permanently. If reception levels are not sufficient, repositioning or use of repeaters may be necessary. Check Signal Reception
1. Go to the RF Module main screen ( Menu , 5 , 230. RF Module ), select the Module then press Enter . 2. From the Actions menu, select Application Logs/Graphs ( Enter , 8. Application Logs/Graphs ). 3. Select 1. Module Stats and press Enter . The Application Log screen will show the SSI Signal Strength. The lower the negative number, the higher the signal strength.
4 Bars>= -75VERY GOOD Reception rates > 98% 3 Bars<-75 and >=-85GOOD Reception rates > 95% 2 Bars<-85 and >=-90FAIR Reception rates < 95% 1 Bar<-90 and >= -95POOR Reception rates <70% 0 Bars<-95FAIL Reception rates <50% OPEN Module alarms
Emerson Wireless Module System — Module Commissioning Tips diagram (page 2)
Fig. 5 · Module Commissioning Tips

Table 2 - SSI Signal Strength Values

Wireless Module System Parts and Accessories

Figure 3 - Overlapping Coverage Area

Part NumberRF Description 814-3550Wireless Gateway 902MHz 814-3560Wireless Repeater 902MHz, 24VAC 814-3570Wireless Repeater 902MHz, 120VAC 501-1121Temp Sensor, General Purpose 508-9101Temp Sensor, Product Simulator 201-1160Temp Sensor, NSF 140-6801Optional wall mount 5V power supply

For a copy of the full Wireless User Manual, scan the QR Code:

Table 3 - Ordering Information

Document Part # 026-4255 Rev 3 Page 2 of 2

This document may be photocopied for personal use. Visit our website at http://www.climate.emerson.com for the latest technical documentation and updates.

Join Emerson Technical Support on Facebook. http://on.fb.me/WUQRnt For Technical Support call 833-409-7505 or email ColdChain.TechnicalServices@Emerson.com

The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applica-

bility. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.

Emerson Wireless Module System — Wireless Module System Parts and Accessories diagram (page 2)
Fig. 6 · Wireless Module System Parts and Accessories
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Emerson Wireless Module System

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Emerson Wireless Module System

Be the first to ask — other owners or our team will answer.

Original document

Emerson Wireless Module System manual PDF

2 pages·638 KB·Communications·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…