

PRODUCT DESCRIPTION S.I.N.: 834-300 PERMATEX〉 Medium Strength Threadlocker BLUE is a medium strength anaerobic threadlocking material, which cures between engaged threads to form a unitized assembly that resists virtually all leakage, shock and vibration. The product is a single component, anaerobic liquid that cures when confined in the absence of air between close fitting metal surfaces. Ideal for all 1/4 inch to 3/4 inch diameter nut and bolt assemblies. Excellent chemical resistance with a temperature resistance range of -175°C to +150°C (-65°F to +300°F). Easily removable with hand tools for servicing requirements. OEM Specified. NSF White Book registered.
threads with Permatex Surface Prep and allow 30 seconds to dry . Priming is not required if the material is an Active Metal. If unknown, it is always best to use the primer. 3. Shake the product thoroughly before use. 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application. 5. For Thru Holes, apply several drops of product onto the bolt at the nut engagement area.

For Blind Holes, apply several drops down the female threads into the bottom of the hole. As threads are engaged, compressed air forces the product upwards into the threads.

For Cleanup 1. Residual liquid films and/or fillets outside the joint are readily soluble in Permatex Brake and Parts Cleaner. 2. Cured product can be removed with a combination of soaking in Permatex Gasket Remover and mechanical abrasion such as a wire brush.
DIRECTIONS FOR USE For assembly 1. Clean all threads (Bolt and Hole) with a cleaning solvent such as Permatex Brake and Parts Cleaner and allow to dry. 2. Determine if the threads to be bonded are Active or Inactive Metals (Ref: Cure Speed vs. Substrate on the second page). If material is an Inactive Metal, spray all
For Disassembly 1. Remove with standard hand tools.
NOT FOR PRODUCT SPECIFICATIONS. THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY. PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)

Technical Data Sheet Medium Strength Threadlocker BLUE
Temperature Resistance Product temperature range from -175°C to +150°C (-65°F to +300°F). The Breakaway and Prevailing Torque values decrease as temperature increases, however the assembly remains effective against vibration and leakage.
For Reassembly 1. Remove loose product from nut and bolt. 2. Apply primer to all threads, regardless of metal type. 3. Assemble and tighten as usual.
Chemical / Solvent Resistance The product retains effective properties in contact with automotive fluids, such as motor oil, gasoline, brake fluids, transmission fluids, alcohol and antifreeze solutions.
Typical Value Chemical Type Anaerobic Dimethacrylate Ester Appearance Opaque Blue Fluorescent Liquid Specific Gravity 1.0 Viscosity @ 25°C, cP 800 to 1,600 Brookfield RVF, spindle #3, @ 20 RPM Flash Point (TCC), °C (°F) >93 (>200)
GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
TYPICAL CURING PERFORMANCE Cure speed vs. substrate The rate of cure will depend on the material used. PERMATEX® Medium Strength Threadlocker BLUE will react faster and stronger with Active Metals. However, Inactive Metals will require the use of a primer (Surface Prep) to obtain maximum strength and cure speed at room temperature.
This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). It is recommended to confirm compatibility of the product with such substrates.
OEM Interchange Manufacture OEM Specifications Numbers BMW 07-58-9-056-031 0121874 Chrysler (Mopar) 4318031 Fiat 976173410 639147100 639197110 Ford EOAZ-19554-AA WSK-M2G351-A5 GM 12345382 9985283 1700.09985283 Isuzu 1-8844-9032-0 1-8844-9033-0 9-8893-2601-0 9-8893-2605-0 Maxiun 15060003 Mazda 105177743 Mercedes Benz A00398931710011 A00398931710002 A00398931710004 A00398931710005 Opel L0010184 L0020184 Saab 7990963 7496268 Scania 814283 Toyota 00001-01003 Valmet 78723013 Volvo 591255 1161054 8701007 VW/Audi AMV197500
Cure speed vs. temperature The rate of cure will depend on the ambient temperature. Full cure is attainable in 24 hours at room temperature, 22°C (72°F), or 1 hour at 93°C (200°F).
Cure speed vs. primer To shorten cure time or if an inactive surface is present, applying a primer (Surface Prep) to the surface will improve cure speed. A 3/8-16 steel nut and bolt assembly will fixture in 5 minutes using a primer, while fixturing will occur in 20 minutes without a primer. Full cure in 24 hours for both procedures.
PERFORMANCE OF CURED MATERIAL (After 24 hr at 72°F on 3/8-16 steel Grade 8 Nuts and Grade 5 bolts)
Typical Value Range Breakaway Torque, Nm, 12 8 to 17 (in.lbs) (110) (70 to 150) Prevail Torque, Nm 5 3 to 7 (in.lbs) (43) (25 to 60) Where Breakaway Torque is the force required to initiate the fastener movement and Prevail Torque is the force required to disassemble the fastener once Breakaway Torque has occurred.
STORAGE Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8° to 28°C (46° to 82°F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container.
Permatex is a trademark of Permatex, Inc. © 2004 All rights reserved

Technical Data Sheet Medium Strength Threadlocker BLUE
NOTE The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. Permatex, Inc. specifically disclaims all warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Permatex, Inc. products and disclaims any liability for consequential or incidental damages of any kind, including lost profits. This product may be covered by one or more United States or foreign patents or patent applications.
Permatex is a trademark of Permatex, Inc. © 2004 All rights reserved
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.