


Download the Rachio App to begin
setting up your new controller.

What’s in the box?
We have a team of experts ready to help. If you run into any problems, please contact Rachio customer support.
Complete support documentation, videos and more are available on our support site.
power adapter 4 screws with anchors
cover · base

What you’ll need...
2.4 GHz or Dual Band Network Required
The Rachio controller uses wireless communications and must be installed within range of a strong signal source for reliable performance. You’ll need to know your Network (SSID) & Password to connect to your network.
phillips screwdriver wire strippers
Requires iOS devices 9.3 or newer or Android 4.0 or newer.
The Rachio controller is designed to be installed indoors. If installing outdoors, a weather-resistant enclosure is required. Reference page 23 for more information.
hammer (for drywall installs) drill (for drywall installs)

Download the Rachio app at www.rachio.com/download
Create a Rachio user account to set up and manage your controller. You’ll need to create a username and password to connect your controller.

Install 3
Test your sprinkler system. Check your sprinkler system by turning on each zone with the old controller. Find and repair any issues with your sprinkler system prior to installing your Rachio controller.
Connect your controller to Wi-Fi using your smartphone and the app at the location where you will install the controller. Connecting to Wi-Fi before installation ensures the signal is strong enough before disconnecting any wires.
The Rachio app will guide you through connecting your controller to Wi-Fi.
Snap a few pictures. Open the old controller. Use your smartphone to take a few photos of the wiring inside the old controller from different angles. This will come in handy when it’s time to wire your Rachio controller.
For Wi-Fi connection tips, or if you encounter issues during the process, please reference page 31.
Unplug your old controller. Disconnect the wires from your old controller, then remove it from the wall. You’re ready for installation.

Attach it to the wall. Remove the controller’s cover from the base and attach to the wall using the included screws. Wall anchors are included for drywall. Make sure your wiring and power adapter will reach the Rachio controller.
Connect the power cord. Insert the power connector into the controller’s power port in the lower right-hand corner of the wiring bay. Finally, plug the transformer into a wall outlet.
Wire it up. Insert sprinkler wire through the opening on the base. Connect the wires to the corresponding terminal locations.


Required Wiring Your controller is designed for 8 or 16 zones, depending on the model you have purchased. There are multiple Common “C” termi nals for convenience; any or all of them can be used. Zone wires connect to the numbered terminals. Only install one valve wire per terminal. Power and ground wires are not needed.

Advanced Wiring If you have a master valve, pump start relay, hydraulic indexing valve, rain or flow sensor, see Advanced Wiring on page 21.

Press the Arrow Buttons to select the zone you want to run. Press the Select Button to start and stop the Selected Zone. When you start a zone, it will begin watering immediately and then stop after a short duration.
SELECT BUTTON
SELECTED ZONE

Factory Reset (Can’t be undone)
To connect to a new network, you’ll need to reset the Wi-Fi connection on your controller.
To uninstall the controller from an account, perform a Factory Reset to clear the controller’s settings.


For detailed instructions, visit rachio.com/update-wifi
For detailed instructions, visit rachio.com/factory-reset

An enclosure is required for hardwiring installations and/or
outdoor installation. For details, reference
Advanced
If you’re using more than one controller, do not share ANY wires
between them - a relay is required. For further details, reference
The controller is designed for 18-gauge sprinkler, solid copper
wire. Up to 14-gauge wire can be inserted into the terminals
without causing damage. If you have thicker gauge wires, were
commend retrofitting with 18-gauge wires using a terminal strip.


A master valve is a “normally closed” valve installed at the supply point of the main line that opens whenever a zone is operating.
The Rachio controller is designed to be installed indoors. If you
need to install outdoors, a weatherproof enclosure is required.

Complete this wiring only if you have a master valve installed in your irrigation system.
Install the Master Valve wire in the “M” terminal slot, and enable the Master Valve in the
Rachio App.
For outdoor install instructions visit www.rachio.com/outdoors
For detailed instructions, visit rachio.com/master-valve
You can purchase an enclosure at www.rachio.com/store

Hydraulic Indexing Valve Wiring
A pump start relay serves as a switch that activates 110-220VAC power to the pump when the Rachio controller’s master valve is enabled. Since the Rachio controller outputs 24VAC, a pump start relay is required when using a pump with the Rachio controller.
Indexing valves offer a central hub to automate multiple zoned irrigation systems. Usually consisting of one inlet and 3+ outlets, indexing valves can operate on city water or pumps. An indexing valve will water on a zone-by-zone basis, diverting the water supply from one outlet to another in a rotational direction. The order of the zones cannot be changed on an indexing valve and are predetermined by the order in which they were installed. For more information, please visit www.rachio.com/indexing
Install in the “M” terminal slot, and enable the Master Valve from the device settings under Advanced within the Rachio App. The controller does not provide main power for a pump.
For detailed instructions, visit rachio.com/pump
Install in the “M” terminal slot, and enable the Master Valve in the Rachio App.
If your system’s water supply comes from city water, install following the Master Valve wiring instructions, page 22.
If your water supply is a pump, a Pump Start Relay is required when using a pump with an Indexing Valve.

Rain Sensors will temporarily suspend watering by the irrigation controller when moisture is detected. Rain sensors normally have three wires; common, normally open and normally closed. Rachio controllers use normally closed wiring (sometimes labeled NC). For more information, visit www.rachio.com/rain-sensor
Wireless Rain Sensors · Wired Rain Sensors

Flow Sensors
Make sure your Rain Sensor is working. Verify operation of the rain sensor and proper wiring.
Flow Sensor are used to measure the amount of water flowing through an irrigation system in Gallons Per Minute (GPM). Flow sensors are being used to monitor water usage and detect abnormal use. For more information, visit www.rachio.com/ flow-sensor.

I can’t connect to Wi-Fi.
The controller must be setup via the Rachio mobile app for initial activation.
Disable cellular data in your phone’s settings; if in doubt, put your phone into Airplane Mode and turn on the Wi-Fi manually.
If the controller fails to connect, note the light code displayed on the controller. To troubleshoot light codes, please reference page 32 and/or visit www.rachio.com/light-codes

My controller is offline. Check your Wi-Fi network. Check your local network. Are other connected devices working properly?
Light One (Booting Up) A blinking light means the device is booting up. Once the light turns solid you can add the controller to your account. You’ll be prompted to confirm the network you want to connect to.
Light Two (Connecting to Wi-Fi) This light will begin blinking as the controller tries to connect to your Wi-Fi network. Once connected to Wi-Fi, the light will turn solid.
Reset your router. Make sure your router has the most recent firmware update.
Light Three (Connecting to Rachio Cloud) This light will begin blinking as the controller attempts to connect to Rachio’s servers. Once connected, it will turn solid.
Restart the controller. Power cycle the controller. Simply unplug the device and plug it back in. Keep an eye on the Rachio light; which light (1-4) does it light up to? If stuck at light 2, perform an Update Wi-Fi Network on the controller.
Light Four (Online) This light will begin blinking until you enter the controller’s serial number. The light will turn solid once your controller is online.

My zones aren’t running.
Is there debris in valve? Turn off water to the system. Remove top of valve via twist or screws. Remove diaphragm assembly and clean the interior of the valve. Inspect the diaphragm for tears. Replace the diaphragm assembly if torn. Make sure all components are installed properly when reassembled.
Do you have a Master Valve or Pump? Is the Master Valve toggle enabled? If your system has a master valve or pump start relay, ensure the master valve toggle is enabled within the Rachio App’s device settings.
For detailed instructions, visit rachio.com/valve-troubleshoot
Check your common wire. Is the issue isolated to one or all zones? If all zones, move common wire to a different common terminal to see if the issue continues.
Check zone wiring. Double-check that the wiring matches the photos of your wiring. Swap zone wire with another nearby zone to see if the issue continues.
Not Stopping/Slow Leak

Limited Warranty Rachio warrants that the Product will be free from material defect in materials and workmanship for a period of two (2) years (one (1) year for factory refurbished Products) from the date of purchase from Rachio or an authorized dealer (the “Limited Warranty Period”). Detailed warranty info at www.rachio.com/ warranty.
Privacy We’re committed to being open and honest about how we use data. We will always ask for permission before sharing personally identifiable information like your email address, and we keep your data safe with the same security tools banks use. Learn more about our Privacy Policy at www.rachio.com/privacy
Limited Warranty is subject to the following conditions: You must notify Rachio in writing of the Defective Product during the Limited Warranty Period by visiting www.rachio.com/warranty and return the Defective Product to Rachio on or within thirty (30) days following the date you notified Rachio in writing of the Defective Product.
Don’t throw out your old controller.
You must provide Rachio with proof of the original purchase of the Defective Product from Rachio or an authorized dealer. You must obtain a return materials authorization (“RMA”) number from Rachio.
Let us recycle your old controller. Send it to our headquarters, and we’ll take care of the rest.
Learn more at www.rachio.com/recycle

38 ©2017 Rachio, Inc.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.