Instruction/ maintenance manual of the product Racetrack RAE4272-RNCY Bretford
Go to page of 7
CONFERENCE T ABLES WITH POWER/DA T A SPHERE (Optional) OR POWER/POWER SPHERE (Optional) Assembly Instructions P ARTS LIST 1 022-1873 R i g h t Leg Assembly 1 022-1871 L e f t Leg Assembly 1 022-2192 M.
STEP 2 Position the table stiffener over holes and attach in place with the #10 x 1/2" screws as shown. Tighten all screws . T urn unit over , position and adjust glides to floor . STEP 1 Lay the wood top down with holes facing up as shown. Attach each leg to the wood top with the 1/4-20 x 5/8" screws as shown.
STEP 3 (For 120" Long T ables Only) 1. Lay the wood tops down with holes facing up as shown. Slide both halves together until edges are aligned. 2. T ake two tite-joint connectors and insert them into two slots as shown. 3. Using small bar rotate the ball counter-clockwise until both halves of table are s e curely drawn together .
STEP 4 Attach each leg to the wood top with the 1/4-20 x 5/8" screws as shown. Make sure the ellipses on each leg face as shown. Tighten all screws.
STEP 5 Position the table stiffener over holes and attach in place with the #10 x 1/2" screws as shown. Tighten all screws . T urn unit over , position and adjust glides to floor . NOTE : See step #6 for installation of optinal power/data sphere or power/power sphere.
STEP 6 Insert RJ- 45 D ata Jack Upon receiving Power/Data Sphere Power half of sphere is ready to install. Other half will require some assembly . End user will be responsible for wiring Data Jack. After wiring is completed you can take insert & Data Jack and insert into data half as shown until it locks.
Presentation Environments® is a registered trademark of Bretford Part #031-4433 Rev .02.27.02 IM Upon receiving this product the grommet s will be already installed in t able top. T ake electric cords and pull them thru the holes at the top and further thru leg openings.
An important point after buying a device Bretford Racetrack RAE4272-RNCY (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bretford Racetrack RAE4272-RNCY yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bretford Racetrack RAE4272-RNCY - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bretford Racetrack RAE4272-RNCY you will learn all the available features of the product, as well as information on its operation. The information that you get Bretford Racetrack RAE4272-RNCY will certainly help you make a decision on the purchase.
If you already are a holder of Bretford Racetrack RAE4272-RNCY, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bretford Racetrack RAE4272-RNCY.
However, one of the most important roles played by the user manual is to help in solving problems with Bretford Racetrack RAE4272-RNCY. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bretford Racetrack RAE4272-RNCY along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
