Instruction/ maintenance manual of the product Hearth Products LUXURY SERIES Breckwell
Go to page of 26
PROFESSIONAL INSTALL ATION IS HIGHLY RECO MMENDED Manufactured by Breckwell Hearth Products Eugene, Oregon Grand Prairie, Texas www.breckwell.com OWNER’S M ANUAL LUXURY SERIES P2700 BRECKWELL HEARTH PRODUCTS C - L - 1001 1 /05 • W ARNING : If your appliance is not properly installed a house fire may result.
Thank you for purchasing the Breckwell Pellet Burning Stove. You are now prepared to burn wood in the most efficient, convenient way possible. To achieve the safest, most efficient and most enjoyable performance from your stove, you must do three things: 1) Install it properly; 2) Operate it correctly; and 3) Maintain it regularly.
Do not operate your stove if you smell smoke coming from it. Turn it off, monitor it, and call your dealer. Never try to repair or replace any part of the stove unless instructions are given in this manual. All othe r work should be done by a trained technician.
INTRODUCTION ----------------------------------------------------------------------------------- --- ------- 2 SAFETY PRECAUTIONS ----------------------------------------------------------------------.
SPECIFICATIONS Width: 23 1/8” Height: 30 ½” Depth: 22 ¼” W eight: 233 lbs. Flue size: 3” or 4” Hopper Capacit y: Up to 50 lbs. (This can vary widely depending on pellet size, length, and diameter) EPA status: exempt Burn time: 1 lb. to 5 .
COMBUSTION AIR SUPPLY For a mobile home installation the stov e must be connected to an outside source of combustion air. A 2” inside diameter metallic pipe, either flexible or rigid, may be attached to the inlet at the stove’s rear (refer to figure 4).
Equivalent Vent Length (EVL) The longer the run of pipe in your installation, the more restriction there is in the system. Therefore, larger diameter pipe should be used. • Use 4” pipe if you have more than 15 feet of equivalent vent length. • Horizontal runs shall not exceed 10’ of EVL.
B. VERTICALLY WITH NEW CHIMNEY SYSTEM (Refer to Figure 7) NOTE: Follow L - Vent chimney manufacturer’s instructions. OPTION: To achieve a center vertical installation a 45º elbow and a clean - out tee can be used to offset the pipe from the exhaust outlet to the rear center of the stove.
E. INSTALLATION THROUGH SIDE OF MASONRY CHIMNEY NOTE: Follow L - Vent chimney manufacturer’s instructions. 1. Position the stove, adhering to the clearances in Figures 1 & 2. Mark the center of t he hole where the pipe is to pierce the masonry chimney.
PANEL CONTROLS (See Figure 11) The blowers and automatic fuel supply are controlled from a panel on the left - hand side of the P2700. The control panel functions are as follows. a. ON/ OFF SWITCH • When pushed the stove will automatically ignite. No other firestarter is necessary.
PROPER FUEL THIS STOVE IS APPROVED FOR BURNING PELLETIZED WOOD FUEL ONLY! Factory - approved pellets are those ¼” or 5/16” in diameter and not over 1” long. Longer or thicker pellets sometimes bridge the auger flights, which prevents proper pellet feed.
RE - STARTING A WARM STOVE If the stove has been shut off, and you want to re - star t it while it is still warm, the “on/off” button must be held down for 2 seconds. IF STOVE RUNS OUT OF PELLETS The fire goes out and the auger motor and blowers will run until the stove cools.
OPTIONAL THERMOSTAT A thermostat may help you maintain a constant house temperature automatically. A millivolt thermostat is required. A fixed wall mount or Breckwell’s hand held model can be used. The control panel can be set up two ways to operate your stove in thermostat mode.
OPERATING SAFETY PRECAUTIONS PLEASE READ THI S! a. Hot while in operation. Keep children, clothing, and furniture away. Contact may cause skin burns. b. If you notice a smoldering fire (burnpot full but no visible flame) AND a heavy smoke buildup in firebox, immediately TURN OFF the stove, but DO NOT unp lug it.
FAILURE TO CLEAN AND MAINTAIN THIS UNIT AS INDICATED CAN RESULT IN POOR PERFORMANCE AND SAFETY HA ZARDS. NEVER CLEAN WHEN HOT. NOTE: Inspect burn pot periodically to see that holes have not become plugged, if so, clean thoroughly. ASH REMOVAL Ashes should be placed in a metal container with a tight - fitting lid.
CLEANING a. Heat Exchange Tubes – Your Breckwell stove is designed wi th a built - in heat exchange tube cleaner. This should be used every two or three days to remove accumulated ash on the tubes, which reduces the efficiency of your unit . Insert the handle end (with hole) of the cleaning tool onto the cleaning rod (refer to figure 14 ).
CHIMNEY CLEANING a. Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relativel y cool chimney flue or a newly started fire or from a slow - burning fire.
When your stove acts out of the ordinary, the first reaction is to call for hel p. This guide may save time and money by enabling you to solve simple problems yourself. Problems can be caused by to only five factors: 1) poor fuel; 2) poor operation or maintenance; 3) poor installation; 4) component failure; 5) factory defect.
STOVE SHUTS OFF AND THE # 3 LIGHT FLASHES Possible Causes: Possible Remedies: (Unplug stove first when possible) 1. The hopper is out of pellets. Refill the hopper.
STOVE FEEDS PELLETS, BUT WILL NOT IGNITE Possible Causes: Possible Remedies: 1. Air damper open too far for ignition. Push the air damper in closer to the side of the stove for startup. In some situations it may be necessary to have the damper comple tely closed for ignition to take place.
STOVE WILL NOT FEED PELLETS, BUT FUEL FEED LIGHT COMES ON AS DESIGNED Possible Causes : Possible Remedies: 1. F use on control board blew Remove the control board. If the fuse appears to be bad, replace it with a 5 Amp 250 Volt fuse. Plug the stove back in and try to run the unit.
• GLASS “SOOT’S” UP AT A VERY FAST RATE • FLAME IS LAZY, DARK, AND HAS BLACK TIPS • AFTER STOVE HAS BEEN ON F OR A WHILE, THE BURNPOT OVERFILLS Possible Causes: Possible Remedies: 1. Stove or vent pipe is dirty, which restricts airflow through the burnpot.
HIGH LIMIT SWITCH KEEPS TRIPPING Possible Causes: Possible Remedies: 1. The convection blower is overheating and tripping the internal temperature shutoff. C lean any dust off of the windings and fan blades. If cleaning the blower does not help, the blower may be bad.
FIGURE 20 ELECTRICAL DIAGRAM 24.
Contact an Authorized Breckwell Pellet Stove Dealer to obtain any of these parts. Never use substitute materials. Use of non - approved parts can result in poor performance and safety hazards.
LIFETIME LIMITED WARRANTY Breckwell Hearth Products warrants to the original consumer purchaser that the Breckwell stove in its original installation is free from defects in material and workmanship from the original date of purchase as follows: Steel fabricated components, excluding burnpot inserts, are covered for five years.
An important point after buying a device Breckwell Breckwell Hearth Products LUXURY SERIES (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Breckwell Breckwell Hearth Products LUXURY SERIES yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Breckwell Breckwell Hearth Products LUXURY SERIES - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Breckwell Breckwell Hearth Products LUXURY SERIES you will learn all the available features of the product, as well as information on its operation. The information that you get Breckwell Breckwell Hearth Products LUXURY SERIES will certainly help you make a decision on the purchase.
If you already are a holder of Breckwell Breckwell Hearth Products LUXURY SERIES, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Breckwell Breckwell Hearth Products LUXURY SERIES.
However, one of the most important roles played by the user manual is to help in solving problems with Breckwell Breckwell Hearth Products LUXURY SERIES. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Breckwell Breckwell Hearth Products LUXURY SERIES along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
