Instruction/ maintenance manual of the product A5 Braun
Go to page of 32
Millennium W A R N I N G Read manual before installing or servicing lift. Failure to do so may result in serious bodily injury and/or property damage. ual Man "Providing Access to the World" International Corporate Hdqrs: P.
NL917IB e5*72/245*95/54*0110*00 1-800-THE LIFT™ BRAUNLIFT .COM™ The Braun Corporation DOT Public Use Lift MODEL# Max. Lifting Capacity - 800 lbs. PATE NT PENDING- 5,261,779-6,065,924-6,238,169-6,4.
Page 1 Contents T roubleshooting and Maintenance Lift T erminology ............................................................ 2 Switch and Sensor Locations ..................................... 3 Certi fi cation Checklist Diagnostic Procedures ....
Page 2 Lift T erminology U P D OWN 3 2 8 1 9 FO LD U N F O L D 3 2 8 2 0 Hand-Held Pendant Control T op Parallel Arms (2) Adjustable Quiet-Ride Stow Blocks (2) Main Cylinders (2) V ertical Arm Covers .
Page 3 Switch and Sensor Locations * Bridging Microswitch 31010F A Pressure Switch 31 199 Threshold Strip Switch 31221A (Qty . 2) Outer Barrier Raised Magnetic Sensor 32645NA60 Outer Barrier Latched Magnetic Sensor 32645NA60 Outer Barrier Raised Magnet 31664 Outer Barrier Latched Magnet 31664 *Note: Mirror image for right (front) pump lifts.
Page 4 The following operations and conditions must be functionally veri fi ed in order for the lift to be FMVSS 403/404 compliant. If an operation does not function as described or a condition is not met, follow the refer- enced procedures to correct the problem or contact a Braun Corporation Product Support representative at 1-800-THE LIFT ® .
Page 5 1. Lower the platform to the ground level loading position. 2. Remove the pump cover . 3. T urn the adjustment screw (shown below) counter clockwise until the outer barrier does not raise when the Up button is pressed.
Page 6 Platform Angle Adjustment Wedges Angle A equals Angle B . ✓ B Figur e C A Approximately 1” Clearance Figur e D Millennium “NL” Series Century “NCL” Series Vista “NVL” Series Inboard Outboard Inboard Outboard Wedges T oe must angle down slightly .
Page 7 Platform Angle Adjustment Screws Adjustment Screw Allen Head A B Platform Angle Adjustment Adjustment Allen screws are provided on each side of the lift platform for adjusting the platform angle. Adjust platform angle as speci fi ed on previous page.
Page 8 Platform Floor Level Adjustment Diagnostics: Diagnostic codes have been established in event the lift platform fl oor position does not set (the lift does not sound three “beeps” - see Step 5 above).
Page 9 H G Platform Stop Block Inboard V ertical Edge of V ertical Arm Bridging Microswitch Adjustment Screw Bridging Micr oswitch Adjustment Bridging Microswitch: The bridging microswitch is located at the bottom of the right (front) vertical arm. See Photos A and B.
Page 10 T o better understand the Braun LCD T rouble shooting display you must fi rst understand the numbers that appear on the screen. There are Flashing Codes, Solid Error Codes, and Solid Normal Operational Codes.
Page 1 1 57 – Outer barrier is not up and latched and ground detect switch did not deactivate (Century and Vista only) 58 – Outer barrier is not up and latched and the plat- form is 3” above the.
Page 12 Speci fi ed (recommended) A vailable Braun Lubricant T ype Lubricant Amount Part No. LO - Light Oil LG - Light Grease Light Grease Lubriplate 14 oz. (Multipurpose) Can Light Penetrating Oil LPS2, General Purpose 1 1 oz. (30 weight or equivalent) Penetrating Oil Aerosol Can Stainless Stick Door-Ease 1.
Page 13 Maintenance and Lubrication Schedule Maintenance and lubrication procedures must be performed as speci fi ed by an authorized service technician. Failure to do so may result in serious bodily injury and/or property damage. Proper maintenance is necessary to ensure safe, troublefree operation.
Page 14 Maintenance and Lubrication Schedule Upper/lower fold arms (2) Platform pivot pin bearings (4) Lower fold arm bearings (8) Inner roll stop pivot bearings (2) Inner roll stop lever bearings (2).
Page 15 Maintenance and Lubrication Schedule Replace damaged parts and resecure as needed. Apply Light Oil. Resecure, replace or correct as needed. Inspect lower fold arm pins (2), axles (2) and beari.
Page 16 NOTES This page intentionally left blank..
Page 17 Lift Electrical Schematic NL917-05-025.ai BK(6) BK(4) GN(20) BU / WH(20) BU / WH(20) RD / WH(20) RD / WH(20) BU / BK(20) RD / BK(20) GN / WH(20) GN / WH(20) BU(20) GN(20) GN(20) GN(20) PK(20) .
Page 18 Unfold for: Lift Electrical Schematic Lift Wiring Diagram Platform Lights (Option) Circuit Sentry (Circuit Breaker) Bat. Aux. Lift Power Cable 205-0712-37 Pump Module Power Feed 26082A-4 Connects to Vehicle Battery (+) Positive Post Lead Wire 13362A GN(20) BK(20) BK(20) BK(20) BK(20) BK(20) or Note polarity of diode.
Page 19 Hydraulic Schematic Outer Barrier Cylinder Orifice Pump Side Cylinder BACKUP PUMP 2500 PSI Secondary Valve Folding Relief Valve Lifting Relief Valve Down Val v e 1900 PSI PUMP Opposite Pump Cylinder M Orifice Bridging Valve 800 PSI .
Page 20 Hydraulics Parts List ✓ Seal Kits: If repairing a cylinder , order Seal Kit #1500-0500 P . * Raw material items ordered and priced per inch (order speci fi ed length). 16 Cartridge #26078 13 “Down and Bridge” V alve (complete) 14 Cartridge #24612 13 “Duel Relief” V alve (complete) 12 Coil #31 122 Coil #31 122 15 Item Qty .
Page 21 Hydraulics Diagram Pump Side Cylinder Opposite Pump Side Cylinder Hydraulic Pump Manual Backup Pump 27 1 2 33 20 18 21 27 3 3 26 25 25 23 30 29 22 29 4 5 19 28 29 12 11 24 15 Roll Stop Cylinder 31 6 32 28 17 7 36 10 8 9 34 35 FRONT PUMP FRONT PUMP REAR PUMP Hydraulic Repair For repair of a hydraulic hose or cylinder, read this.
Page 22 Pump Module Parts List * Apply red #271 Thread Locker Loctite ® to the four hex bolts (items 27 and 28) if a blue nylon patch is not present on the bolts when retro fi tting an M268-01 13 pump assembly . Loctite ® is available from The Braun Corporation under part number 1 1522-1.
Page 23 Pump Module Diagram Pump Mounting Bolts Apply red #271 Thread Locker Locktite ® to the three pump mounting bolts (items 27 and 28) if a blue nylon patch is not present on the bolts when retro fi tting an M268 pump assembly . Loctite ® is available from The Braun Corporation under part number 1 1522-1.
Page 24 42” Floor -to-Gr ound Lift Repair Parts List 1 1 Base Weldment 915R5142NW30 915F5142NW30 918R5142NW33 918F5142NW33 2 1 Cover , Pump, 2-Piece, Back-Bottom 915-0513RNPT 915-0513FNPT 915-0513RNPT 915-0513FNPT 3 1 Cover , Pump, 2-Piece, T op-Front Assy .
Page 25 42” Floor -to-Gr ound Lift Exploded View 114 111 109 104 113 50 116 109 111 73 31 153 77 79 113 50 116 174 73 41 162 178 178 165 69 69 179 31 153 77 174 149 107 89 149 107 112 104 113 112 36.
Page 26 48” Floor -to-Gr ound Lift Exploded View 114 111 109 104 113 50 116 109 111 163 6 79 113 50 162 174 153 85 77 53 115 115 115 85 149 107 89 149 107 2 29 33 38 34 35 8 26 112 104 113 112 112 1.
Page 27 48” Floor -to-Gr ound Lift Repair Parts List Part Numbers of Items Identical on All Lift Models 1 1 Base Weldment 985R5148NW30 985F5148NW30 985R5148NW33 985F5148NW33 985R5148NW34 985F5148NW3.
Page 28 NOTES This page intentionally left blank..
Over 300 Braun Dealers W orldwide "Pr oviding Access to the W orld" ® "Pr oviding Access to the W orld" International Corporate Hdqrs: P .
HZg^Zh HZg^Zh Millennium CA CA Public Use Wheelchair Lifts Patent #5,261,779 Patent #6,065,924 Patent #6,238,169 Patent #5,261,779 Patent #6,065,924 Patent #6,238,169 Patent #6,464,4.
An important point after buying a device Braun A5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Braun A5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Braun A5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Braun A5 you will learn all the available features of the product, as well as information on its operation. The information that you get Braun A5 will certainly help you make a decision on the purchase.
If you already are a holder of Braun A5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Braun A5.
However, one of the most important roles played by the user manual is to help in solving problems with Braun A5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Braun A5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
