Instruction/ maintenance manual of the product 2461 Brady
Go to page of 140
Brady Bradyprinter Models 2461, 3481, and 6441 Operator’s Manual (TEMP COVER) (DO NOT PRINT) (DO NOT print this page).
(DO NOT print this page).
Copyright Information: CG Triumvirate is a trademark of Agfa Corporation. CG Times based upon Times New Roman under license from the Monotype Corporation.
Agency Compliance and Approvals: C US Listed UL1950 Information Technology Equipment C22.2 No. 950-M93 EN60950 For 230 Volt Operation (Europe): Use a cord set, marked “HAR,” consisting of a min H05VV-F cord which has a minimum 0.
Important Safety Instructions: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying this unit. This unit has been carefully designed to provide years of safe, reliable performance.
.
i Printer Overview 1.0 About the Printer ........................................................... 1 1.0.1 Standard Features ........................................... 2 1.0.2 Optional Features ........................................... 2 1.1 Option Installation .
ii Using the Front Panel 4.0 Operation .................................................................... 27 4.0.1 Ready Mode: Normal Operation .................... 27 4.0.2 Menu Mode: Configuration ............................ 28 4.0.3 Quick Test Mode: Print Test Labels .
iii 5.2 Printhead Replacement .............................................. 73 5.3 Maintenance Schedule ............................................... 74 5.3.1 Cleaning the Printhead .................................. 75 5.3.2 Cleaning the Platen Roller .
iv Appendix D GPIO Port Description ...................................................... 111 Appendix E Menu System Multi-Language Support ............................. 113 Advance File Handling Information ................................... 116 Appendix F Saving a Configuration File .
1 1.0 About the Printer Congratulations on your purchase of a Bradyprinter Model 2461, 3481, and 6441 hereafter referred to as ‘the printer’, blends the rugged durability of die- cast construction with state-of-the-art electronics and user-friendly features to redefine the standard in industrial thermal printers.
2 1.0.1 Standard Features This printer offers the following standard features: Bradyprinter Standard Features Listing Model Feature 2461 3481 6441 Printhead Density (Dots Per Inch) 203 300 600 Direct .
3 External Keyboard Support An interface for the connection of the Passport™ keyboard. External Media Rewinder Separate device with and 8” roll capacity to rewind labels and backing material.
4 Peel and Present Mechanism (requires the Internal Rewind option ) An output control device that automatically separates printed labels from the backing material and allows subsequent printing to occur only after the removal of a previously printed label .
5 1.1 Option Installation The following table lists the available options and the recommended qualification level of the installer. For detailed information concerning a specific option, contact your dealer or Technical Support.
6 1.2 Hardware Components The following drawing highlights the user-assessable components of the printer. Items denoted with an asterisk (*) are optional equipment.
7 2.0 Unpacking the Printer Inspect the shipping container(s) for damage; if evident, immediately notify the shipping company to report the nature and extent of the damage. The printer has been carefully packaged to avoid damage during transit. In order to operate the printer, you will need to remove the tape and foam placed there for shipment.
8 2.0.1 Inspection After removing the printer from the packaging material, check the contents of the package. In addition to this manual, the following items should be included: Ø Printer Ø Power Cord Ø Accessories CD Ø Any special or additionally purchased items.
9 2.1 Media and Ribbon Selection The following is a limited overview of media characteristics. For complete information and advice regarding your specific application needs, always consult a qualified media specialist or a Media Representative.
10 • The second method would be to change the ‘Print Control / Heat’ menu setting (selectable as ‘Heat Setting’ in most software programs). Increasing this value causes more energy to be transferred to the media , resulting in a darker image.
11 3.0 Installation This section explains how to connect the printer, and load it with media and ribbon . þ Note: When connecting the AC Power Cord or interface cables to the printer, ensure the Power On/Off Switch is in the ‘Off’ position. Œ Place the printer on a firm, level surface.
12 3.0.1 Communicatio ns Using a data detection process, the interface selection occurs automatically in the printer. At power-up, the printer begins monitoring the interface ports for activity. When the host transmits data, the printer port detecting this data is set ‘active’ and remains active as long as data flow continues.
13 Serial Port : The serial interface supports RS-232C and, if equipped, RS-422 communications. The following list of serial port settings is menu-selectable and must match the host computer’s serial port settings; see Section 4.
14 3.1 Loadi ng Media Begin loading as follows: Œ Raise the Access Cover. • Rotate the Printhead Latch forward and raise the Printhead Assembly. Ž Slide the Media Guide out away from the frame and then lower it to the down position. • If using roll media, the Media Hub can accept 3.
15 3.1.1 Roll Media This loading method is roll type media applications. To load: Œ Slide the Roll Media onto the Media Hub until it rests against the Backstop. • Route the media as shown: under the Media Idler, through the Media Sensor, then out the front of the printer.
16 3.1.2 Fan-Fold Media This loading method is for tag and fan-fold type media applications. To load: ΠBring the media in through the Bottom or the Rear Media Slot.
17 3.2 Media Sensor Adjustment The Media Sensor needs to be positioned so that the printer can detect the presence of media and the top-of-form ( except for continuous stock, where the TOF is set through programming; see Label Length, Section 4.1.2). To adjust : ΠWith media loaded, as described in Section 3.
18 3.3 Loading Ribbon Ribbon is required with thermal transfer media. Depending upon the type of Ribbon Supply Hub (see the next page for examples), the printer must use either ribbons with the ‘coating side in’ or ribbons with the ‘coating side out’.
19 þ Note: Directional Arrows near the Ribbon Supply Hub indicate the correct ribbon route. Ribbon is available with the ink (coating) layer wound ‘in’ or ‘out’.
20 3.4 Quick Media Calibration + When ‘Uncalibrated’ is displayed, follow the Media Sensor Calibration procedure in Section 5.0. At the factory, the printer is calibrated to sense a wide range of media types.
21 3.5 Outputting Labels In addition to directly outputting labels from the printer, there are several optional output configurations available. 3.5.1 Rewinding With the Internal Media Rewinder option, the printer can wind the printed labels and backing material .
22 ‘ Route the media back to the Media Rewind Hub, as shown below. ’ Insert the leading edge into a Slot on the Media Rewind Hub then insert the Media Clip into a Slot to secure it in place. “ Position the Rewind Retainer lightly against the edge of the media on the Media Rewind Hub.
23 3.5.2 On-Demand Dispensing When equipped with the Peel and Present option, labels are dispensed from the printer one at a time, separated automatically from the liner for immediate application. ΠWith the Peel and Present Mechanism installed on the printer, pull outward on the Latch and allow the Roller Bracket to swing forward.
24 • If installed, remove the Media Clip and the Rewind Retainer from the Media Rewind Hub. Route the Backing Material around the Media Rewind Hub, as shown. ‘ Insert the leading edge into a Slot on the Media Rewind Hub then insert the Media Clip into a Slot to secure it in place.
25 3.5.3 Cutting When equipped with one of the cutter options, cut labels are dispensed from the printer. Œ Ensure the leading edge of media is clean, straight and firmly attached to the liner. • Load media according to Section 3.1, except route the media out through the Opening of the Cutter Assembly.
26.
27 4.0 Operation The front panel is comprised of three indicator lights, a Liquid Crystal Display and five mode-dependant keys . The selectable modes (Ready, Menu and Quick Test) and the related functions of the printer keys are detailed below.
28 4.0.2 Menu Mode : Configuration (Ready Light ‘Flashing ’ ) Œ The DOWN ARROW key scrolls to the previous menu item on the same menu level. It also decrements numerical values in most menu selections. • The UP ARROW key scrolls to the next menu item.
29 4.0.3 Quick Test Mode : Print Test Labels þ Note: The Quick Test Mode functions are disabled while processing data from communications interfaces until the Host Timeout value expires. Œ The DOWN ARROW key scrolls to the previous test function. • The UP ARROW key scrolls to the next test function.
30 4.0.4 Indicator Lights Œ ‘On’ indicates that the printer is powered ‘On’ and, after initialization, it indicates the Ready Mode. ‘Slow Flashing’ indicates the Menu Mode. ‘Fast Flashing’ indicates data is being received and processed.
31 4.0.6 Resetting the Printer Depending upon the method used, there are three reset levels possible: 4.0.6.1 Soft Reset To reset the printer and clear any temporary host settings: With the printer ‘On’, press and hold the CANCEL key for approximately four seconds.
32 4.1 The Me nu System Printer operation can be controlled through the user interface, allowing the operator access to these six menu system branches: • Media Settings • Print Control • Printer.
33 4.1.1 Entrance and Exit Prompts With ‘Ready’ displayed on the LCD, press the key to enter the Menu Mode . þ Note: Wh ile in the Menu Mode , the printer will stop processing new DPL (or bitmapped) data.
34 4.1.2 Media Settings MEDIA TYPE Selects the printing method. DIRECT THERMAL For use with heat sensitive media . ² THERMAL TRANSFER For use with media requiring a ribbon to create an image. SENSOR TYPE Selects the top-of-form (TOF ) sensing method for the media .
35 4.1.3 Print Control + Refer to Section 2.1.1 for detailed information on print quality controls. HEAT ² 10 (0-30) Controls the ‘burn-time’ of the printhead. This is the equivalent of Heat Setting on most label software programs. PRINT SPEED Controls the rate of label movement during the printing process; see Appendix C.
36 Print Control (continued) CUSTOM ADJUSTMENTS ♦ These factory adjustments independently change the listed parameters to finely tune the printer and compensate for slight mechanical differences sometimes evident when multiple printers share label formats.
37 4.1.4 Printer Options MODULES Memory available for user storage of graphics, fonts and label formats. (The physical presence of the respective memory module must be detected to show the function selections for that module in the menu system.) See Appendix C for a listing of all possible modules.
38 Printer Options (continued) CUTTER Used to cut media into separate labels. (The physical presence of a cutter must be detected to show the ENABLE/DISABLE selections.) ENABLED Enables label cutting. ² DISABLED Disables the cutter . NOT INSTALLED No cutter is detected.
39 4.1.5 System Settings CONFIGURATION FILE Options for storage and recall of printer configuration files. See Appendix F for details. RESTORE AS CURRENT Provides a list of available configuration files. Selecting a file from the list causes a printer reset; afterward, the printer is configured according to the activated file.
40 System Settings (continued) DOUBLE BYTE SYMBOLS When equipped with the ILPC option, this selects the code page used to print double byte fonts unless otherwise specified in DPL; see the Programmer’s Manual for details.
41 System Settings (continued) CONFIGURATION LEVEL To upgrade the application program (resident software) version of the printer, the hardware and software compatibility levels must match for the update to be accepted. This information is displayed here; it is also printed on a configuration label .
42 System Settings (continued) SET FACTORY DEFAULTS Parameters in this menu listing with the ‘ ² ’ symbol are the designated defaults. SET FACTORY DEFAULTS Overwrite the current settings with the factory default settings or, if selected, will restore the Factory Setting File.
43 System Settings (continued) PAUSE MODE When enabled, Pause Mode suspends printing between each label until the PAUSE key is pressed. ENABLED Printer requires operator to press the PAUSE key after each label . ² DISABLED Printer completes label batch without pausing between labels.
44 System Settings (continued) þ Note: As indicated, the following menu selections will only appear according to the model of your printer. PLUS EMULATION This instructs the firmware to process specific DPL data as would the Prodigy Plus ® printer without all of the variations.
45 System Settings (continued) þ Note: As indicted, the following menu selections will only appear according to the model of your printer. DPI EMULATION For users who want to print DPL files intended for a 203 or 300 DPI printer. ² DISABLED Label formats interpreted as intended for 600 DPI.
46 System Settings (continued) SOP EMULATION Enables the <STX>O and <STX>f print positioning commands to allow backward compatibility with label formats designed for other printers. (When changing these values, the printer will automatically feed two labels to setup the new print position.
47 4.1.6 Communications SERIAL PORT A ♦ Controls the communications settings for Serial Port A. BAUD RATE Determines the serial communication rate. 38400 38400 bits per second 28800 28800 bits per s.
48 Communications (continued) PARALLEL PORT B ♦ Same as Parallel Port A, for an optional Ethernet connection. If not present, this displays ‘NOT INSTALLED’ when accessed.
49 Communications (continued) PROTOCOL The network protocols recognized by the NIC Adapter . IP This protocol is always supported. LAT Local Area Transport is a DEC VMS network protocol that requires a LAT license number. ² ENABLED Protocol is enabled by default.
50 Communications (continued) DISCOVERY This is the address discovery method used by the NIC Adapter if a static address is not utilized. If no server for any of the discovery methods is found, the static value specified above is used. þ Note: For faster NIC Adapter boot times, disable any discovery methods not used.
51 Communications (continued) HOST SETTINGS Settings which affect all communications with a host. HOST TIMEOUT ² 10 SEC (1-60) The number of seconds a communications port must be idle before the printer may process data from a different port. This value is also used to “timeout” an image / label format download.
52 Communications (continued) HEAT COMMAND Allows the user to disable the DPL Heat Command, providing compatibility with other printers. ² ENABLED Normal printer operating mode. DISABLED DPL Heat Commands are ignored. The heat value is controlled via the menu setting; see Print Control, Section 4.
53 4.1.7 Diagnostics HEX DUMP MODE Most commonly used for troubleshooting. Prints data and instructions received from the host rather than interpreting them as label formats; see Section 6.2. ENABLE Prints raw ASCII data received from the host rather than executing the commands.
54 4.2 Display Messages The printer displays several different types of information (if not in the menu system or Quick Test Mode ): Ø User Prompts and Condition Messages (also see Section 4.1.1 for a listing of the Enter/Exit Prompts) Ø Application and Boot Loader Updating Messages (see Section 5.
55 User Prompts and Condition Messages (continued) Displayed Message Description Condition(s) Normal power-up and soft reset condition. Follows the ‘SYSTEM RESET IN PROGRESS’ message after a reset or power-up. Normal power-up and soft reset condition.
56 4.3 Quick Test Mode This section explains the functions of the resident Quick Tests, accessible by pressing the key on the Front Panel. þ Notes: (1) With the exception of the Configuration Label, all Quick Test labels require 4-inch (102mm) wide media to print the entire format.
57 4.3.2 Configuration Label The Configuration Label provides valuable printer database information, as detailed in Section 4.1. þ Note: The Configuration Label content can vary with the application version and printer model.
58 4.3.3 Qui ck Ribbon Test Label The Quick Ribbon Test Label features a compliant picket-fence bar code that can be used to verify thermal transfer and print quality functions. To print a Quick Ribbon Test Label : Œ Press the key. • Use the key to scroll to ‘Ribbon Test Label’ .
59 4.3.4 Dot Test Pattern Label The Dot Test Pattern Label features patterns that exercise all of the thermal elements (dots) of the printhead. The resulting label (see examples below) can be an indication of the printhead’s condition. To print a Dot Test Pattern Label: Œ Press the key.
60 4.3.5 Validation Label The Validation Label is another useful tool for evaluating overall print quality. To generate a Validation Label: Œ Press the key. • Use the key to scroll to ‘Validation Label ’. Ž Use the key to select a quantity; see Section 4.
61 5.0 Media Sensor Ca libration In addition to the Sensor Type selection, Media Sensor calibration ensures that each label is detected correctly and reliably. Perform calibration when the ‘Uncalibrated’ message is displayed. Two different methods are available to calibrate the printer: Standard and Advanced Entry.
62 Standard Calibration (continued) Step Operator Action Displayed Message Comment 3 Press the key to enter the Media Settings menu. See Section 4.1.2 for menu layout. 4 Press the key and scroll to ‘Sensor Calibration’. Press the key to abort this procedure.
63 Standard Calibration (continued) Step Operator Action Displayed Message Comment 7 Proceed according to your media type: Die-cut stock: strip the media from the backing and then reinsert it into the sensor; adjust the Sensor Eye Mark over the center of the backing.
64 Standard Calibration (continued) Step Operator Action Displayed Message Comment 9 Observe the display. Or, for reflective media: Or, for continuous media: The calibration was successful. See note below if another message was displayed. 10 Exit upon successful calibration: B ack out of the menu tree by repeatedly pressing the key .
65 5.0.2 Advanced Entry Calibration Advanced Entry Calibration is the alternate method for special-case media types. The procedure has two parts: 1) Using different sampling algorithms, displayed sensor readings have to be listed for each label and TOF value.
66 Advanced Entry Calibration (continued) Step Operator Action Displayed Message Comment 6 Press the key to scroll to ‘Advanced Entry’. You are entering Advanced Entry Calibration. 7 Press the key. Press the key to abort this procedure. 8 Press the key.
67 Advanced Entry Calibration (continued) Step Operator Action Displayed Message Comment 11 Proceed according to your media type: Die-cut stock: strip the media from the backing and then reinsert it into the sensor; adjust the Sensor Eye Mark over the center of the backing.
68 Advanced Entry Calibration (continued) Step Operator Action Displayed Message Comment 12 From the data collected in Steps 10 and 11, where both the sensor readings are above 20, subtract each Label Value from the corresponding TOF Value. These are the Difference Values .
69 Advanced Entry Calibration (continued) Step Operator Action Displayed Message Comment 13 Using the key, select the Gain Number determined in Step 12. Press the key to select the setting. Or, for reflective media: Selection is denoted with an ‘*’.
70 Advanced Entry Calibration (continued) Step Operator Action Displayed Message Comment 16 Press the key. Using the or the key, set the ‘Paper’ level to the value determined in the previous step. Press the key to set the entry (indicated by the ‘*’) and advance the menu.
71 5.1 Printhead Adjustments To ensure consistent print quality over a wide range of media types and dimensions, the printer is equipped with a Leveling Cam adjustment and a Burn Line adjustment .
72 5.1.2 Burn Line Adjustment The Burn Line has been adjusted at the factory for strict compliance using 6.5- mil (.0065 inch) media, ensuring print quality across a majority of media types. In extreme cases, however, if media of a different thickness or rigidity is used (for example, heavy tag stock ), print quality can change.
73 5.2 Printhead Replacement þ Note: The printhead is fragile; use extreme care when handling and never use a sharp object on the surface. If you have any questions or concerns regarding this procedure, contact a qualified technician or Technical Support before proceeding.
74 5.3 Maintenance Schedule The following list and table detail the recommended items, techniques and schedules to help you safely and effectively clean the printer.
75 5.3.1 Cleaning the Printhead If print quality declines (symptoms include non-compliant bar codes, print dropouts, streaks; see Section 4.3.4), the typical cause is debris build-up on the printhead. Furthermore, when the build-up is not removed it may lead to element failure, greatly reducing the life of the printhead.
76 5.3.2 Cleaning the Platen Roller A platen roller contaminated with grit, label adhesive, or ink can cause a decline in print quality and, in extreme cases, cause labels to stick and wrap around the roller. To clean the platen roller: Œ Turn ‘Off’ and unplug the printer.
77 5.3.3 Cleaning Interior and Exterior Surfaces Interior Surfaces: During operation, dust particles from the media build-up inside the printer. Then, as the media is pulled through the printer, the particles can become attached and cause voids on the printed labels.
78 5.4.1 Updating from Ready Mode Update Procedure for Application Version 2.091 or greater Step Displayed Message Operator Action Comment(s) 1 Using the DOS copy command (where ‘filename’ is the .
79 5.4.2 Updating from Download Mode Required Update Procedure for Application Version 2.08 or earlier * Step Displayed Message Operator Action Comment(s) 1 Press and hold the PAUSE and TEST keys while turning ‘On’ the printer to enter the Download Mode .
80 5.4.3 Possible Problems during an Update The following is list of possible error messages when downloading: þ Note: If experiencing trouble when attempting to download the file to the printer, try the following alternate methods: 1) Use Download Mode (see Section 5.
81 5.5 Boot Loader Program Updates The printer stores the Boot Loader Program in Flash memory on the Main PCB. A feature allows updates to this program via the printer’s interface port.
82.
83 6.0 Problem Resolution Should a problem arise, the information in this section will help you resolve it. The following table lists problems that will not necessarily generate an error message. (For information on messages, see Section 6.1.) + If you have questions, or if problems persist, contact a qualified technician or Technical Support.
84 If experiencing this problem… Try this solution… Intellifont will not print: Intellifont format is Little/Big Endian specific. The printer uses Big Endian.
85 If experiencing this problem… Try this solution… No power (all indicator lights are ‘Off”): • Verify that the AC power cord connection has been made at both the outlet and the printer; also, ensure the power switch is ‘On’. • Verify that the AC outlet is functioning, or try moving the printer to another AC circuit.
86 If experiencing this problem… Try this solution… Nothing happens when trying to print using a software program: • Ensure that the printer is at READY. • Observe the Front Panel, if the READY light does not flash as you send the format check the protocol and port settings between the printer and host.
87 6.1 Fault and Warning Messages All printer functions are internally monitored. If a problem (Fault) or a potential problem (Warning) is detected, the Error Indicator (see Section 4.0.4) will be illuminated. A corresponding message will be displayed (if not within a branch of the menu system or in Quick Test Mode).
88 Printer Fault Messages (continued) Displayed Message Description Possible Solution(s) The printer has detected a Direct Memory Access failure. Try cycling the printer power ‘Off’ and ‘On’. If the fault does not clear, call for service. Consistently low sensor readings were detected.
89 Printer Fault Messages (continued) Displayed Message Description Possible Solution(s) The printer was unable to complete the Media Calibration; or, the printer was powered off or reset during a ribbon, out of stock or TOF fault. Press the FEED key in an attempt to clear the message.
90 Printer Fault Messages (continued) Displayed Message Description Possible Solution(s) Consistently high sensor readings were detected. Press any key to continue. Ensure that media was removed from the media sensor during the appropriate calibration steps; also ensure that no labels are stuck in the media sensor.
91 Printer Fault Messages (continued) Displayed Message Description Possible Solution(s) The printer could not find the TOF mark within the maximum label length setting or it found a TOF in an unexpected place. þ Note: When the printer is set for reflective media, this indication is given for an out of stock condition.
92 Warning Messages : Warning Messages are displayed for a period of five seconds. If multiple Warnings are detected, the display will reflect the highest priority message. Printer Warning Messages Displayed Message Description Action(s) The printer has detected defective printhead elements.
93 6.2 Hex Dump Mode The Hex Dump Mode is a useful tool for diagnosing problems, including communication and DPL syntax errors, allowing a comparison of input strings (sent by host) to output data (received by printer). To decode this information, the Programmer’s Manual is an essential reference.
94.
95 7.0 General Specifications Bar Codes (See the Programmer’s Manual for details. See Appendix B for samples.) Code 39, Interleaved 2 of 5, Code 128 (subsets A, B and C), Codabar, LOGMARS, UPC-A, UP.
96 Environmental Requirements Operating Temperature: 32 ° F – 100 ° F (0 ° C to 38 ° C) Storage Temperature: 0° F − 140° F (-17° C to 60° C) Humidity: 10% − 95% non-condensing Dust: Non-conducting, non-corrosive Electromagnetic Radiation: Moderate RF fields can be tolerated Mechanical Height: 12.
97 Printing Specifications (continued) Print Length Range: with an optional cutter: with an optional peel & present mechanism: .25” – 99” (6.4 mm – 2514.6 mm) 2461&3481 .25” – 55” (6.4 mm – 1397 mm) 6441 1.25” – 99” (31.8 mm – 2514.
98 Media and Ribbon Requirements (continued) E A B C D G H I J F Media Dimensions Designator Description Maximum [1] Minimum [1] A label width 4.65 1.00 B liner width 4.65 1.00 C gap (or notch) between labels [4] – .100 D label length [4] – .250 E media thickness [2] .
99 Appendix A ASCII Control Code Chart Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ctrl @ NUL 0 00 32 20 @ 64 40 ` 96 60 Ctrl A SOH 1 01 ! 33 21 A 65 41 a 97 61 Ctrl B STX 2 02 “ 34 22 B 66 .
100 ASCII Control Code Chart (continued) Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Ç 128 80 á 160 A0 192 C0 Ó 224 E0 ü 129 81 í 161 A1 193 C1 ß 225 E1 é 130 82 ó 162 A2 194 C2 Ô 226.
101 Appendix B Available Fonts and Bar Codes All character fonts and bar codes available with the printer are described in this section. Each font and bar code has a name associated with it for use in programming. Human-readable fonts have numeric names, while bar code fonts have alpha names.
102 The table below lists the font sizes; the numbers indicate the number of dots. Font Height Width Spacing 0 7 5 1 1 13 7 2 2 18 10 2 3 27 14 2 4 36 18 3 5 52 18 3 6 64 32 4 7 32 15 5 8 28 15 5 Font 0: 96-character alphanumeric , upper and lower case.
103 Font 4: 62-character alphanumeric , uppercase. Font 5: 62-character alphanumeric , uppercase. Font 6: 62-character alphanumeric , uppercase..
104 Font 7: OCR-A, size I. Font 8: OCR-B, size III. Font 9: Internal Triumvirate font . The number in the bar code height field sets the point sizes. Larger point sizes can be obtained by increasing the height and width multipliers.
105 Bar Code Summary Data Bar Code fonts have alpha names (left column in the table below). Uppercase alpha names will print barcodes with human-readable interpretations. Lowercase alpha names will print barcodes only. The table is followed by visual samples.
106 Bar Code A: Code 3 of 9 Bar Code B: UPC-A Bar Code C: UPC-E Bar Code D: Interleaved 2 of 5 Bar Code E: Code 128 Bar Code F: EAN-13 Bar Code G: EAN-8 Bar Code H: Health Industry Bar Code (HBIC) Bar.
107 Bar Code K: Plessey Bar Code L: Interleaved 2 of 5 w/modulo 10 checksum and shipping bearer bars Bar Code M: 2 Digit UPC addendum Bar Code N: 5 Digit UPC addendum Bar Code O: Code 93 Bar Code p: P.
108 Bar Code S: UCC/EAN Code 128 Random Weight Bar Code T: Telepen Bar Code u: UPS MaxiCode Bar Code v: FIM Bar Code z: PDF-417 Bar Code WG: USD-8 Bar Code W1c: DataMatrix Bar Code W1d: QR Code Bar Co.
109 Appendix C Module Assignments Memory Module Designator Module Size Volatile* Location / Use A Future Option N/A N/A B Future Option N/A N/A D 1024 KB (default size) Yes Main PCB SDRAM – user add.
110 Available Speeds and Default Settings Printer Speed Ranges and Defaults * Speed Range Default Setting Model IPS MMPS IPS MMPS 2461 Print 2-8 51 – 203 8.0 203 Feed 2-8 51 – 203 8.0 203 Reverse 2-4 51 – 102 4.0 102 3481 Print 2-8 51 – 203 6.
111 Appendix D GPIO Port Description With the optional GPIO PCB, the printer can easily be programmed to interface with most applicator devices. The GPIO functions are enabled and configured using the menu system of the printer (see Section 4.1.4). These parameters are stored in non-volatile memory and saved for subsequent power-ups.
112 GPIO Pin Configuration (as viewed from the rear of the printer) External Start of Print Control Connections for an external Start of Print control can be made (1) directly to Pin 8 using a TTL- level input or (2) with an interface circuit similar to the one shown right.
113 Appendix E Menu System Multi-Language Support This printer provides the user with the ability to download new menu system languages and/or replace the provided translations.
114 Creating a Menu Language: Œ Invoke Excel and open the gemmsglst.xls file. Excel opens the file and the following screen appears. • Click the “Enable Macro” box and the following appears:.
115 Ž Click On Column J and enter your new language, or modify an existing one. Tips: A) Message Size – When entering new messages, reference the ‘MAX’ column: this is the maximum number of characters allowed for this field. Warnings are displayed when the number of characters is exceeded or when trying to modify the MAX value.
116 ‘ Download the generated files to the printer – one method is the DOS copy command: copy small.ls lpt1: /b ’ Reset the printer by pressing and holding the CANCEL key for approximately four seconds. “ Verify the operation by printing a Configuration Label (see Section 4.
117 Ÿ To restore the factory generated EFIGS image, download the file *832296.01A to the printer. This file is located on our web site. The letter at the end of the file name (e.g., A) specifies the revision. Ÿ Downloading the same language twice will automatically delete the first occurrence, but will not free the memory space.
118.
119 Appendix F Saving a Configuration File With application version 5.01, the printer can save and restore complete printer settings, including media calibration parameters, as internal Configuration Files.
120 To save a manually entered setup (for example, an application that required an Advanced Entry Calibration before beginning) as a configuration file using the front panel: Step Displayed Message Operator Action Comment(s) 1 Press the key. You are entering ‘Menu Mode’ .
121 Warranty Information Brady Products Limited Warranty Statement Bradyprinter Models 2461 and 3481 Printer Brady warrants to Purchaser that under normal use and service, the 2461, 3481 and 6441 Prin.
122 Thermal Printhead, Platen Roller, and Belts This warranty* is limited to a period of one year, (365 days), or one million (1,000,000) linear inches of use, whichever comes first, for the 2461, 3481 or 6441 thermal printhead, platen roller, and belts.
123 General Warranty Provisions Brady makes no warranty as to the design, capability, capacity or suitability of any of its hardware, supplies, or software.
124.
125 Glossary alphanumeric Consisting of alphabetic, numeric, punctuation and other symbols. backing material The silicon-coated paper carrier material to which labels with adhesive backing are affixed. Also referred to as “liner”. bar code A representation of alphanumeric information in a pattern of machine-readable marks.
126 defaults The functional setting values returned following a factory reset of the printer. diagnostics Programs used to locate and diagnose hardware problems. die-cut media Media that has been cut into a pattern using a press, where the excess paper is removed leaving individual labels, with gaps between them, attached to a backing material .
127 label A paper or synthetic printing material, typically with a pressure sensitive adhesive backing. label length The distance from the top of the label to the bottom of the label as it exits the printer. label repeat The distance from the top of one label to the top of the next label.
128 reverse speed The backward rate of media motion into the printer during tear-off, peel and present and cutting operations for positioning the label at the start of print position. ribbon An extruded polyester tape with several layers of material, one of which is ink-like, used to produce an image on the label .
129 Index A alphanumeric, 125 application program, 77 ASCII, 93 , 99 - 101 , 105 B bar code, 84, 86, 95, 105 - 108, 125 boot loader, 79 - 81 , 125 burn line, 72, 75, 86, 125 C cable listings, 12, 13 c.
130 M media continuous, 17, 20, 34, 97, 125 backing material, 18, 20, 21, 23 - 25, 61, 64, 97, 98, 125, 126 black mark, 17, 61, 63, 67, 89, 98, 127, 128 die-cut, 17, 97, 126 direct thermal, 9, 10, 34,.
An important point after buying a device Brady 2461 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Brady 2461 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Brady 2461 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Brady 2461 you will learn all the available features of the product, as well as information on its operation. The information that you get Brady 2461 will certainly help you make a decision on the purchase.
If you already are a holder of Brady 2461, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Brady 2461.
However, one of the most important roles played by the user manual is to help in solving problems with Brady 2461. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Brady 2461 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
