
Safety Ensure that your domestic mains supply voltage matches the voltage indicated on the identification sticker located at the back of your set. Where the mains plug or an appliance coupler is used as disconnect device, it shall remain readily operable. On certain models, the light indicator is located at the side of the TV set. The absence of a light indication at the front does not mean that the TV set is fully disconnected from the mains. To disconnect the TV set completely, the mains plug must be pulled out. The TV set’s components are sensitive to heat. The maximum ambient temperature should not exceed 35º Celsius. Do not cover the vents at the back or sides of the TV set. Leave sufficient space around it to allow adequate ventilation. Install the appliance away from any source of heat (fireplace, etc.) or appliances creating strong magnetic or electric fields. Moisture in rooms where the set is installed should not exceed 80% humidity. Moving the set from a cold place to a warm one can cause condensation on the screen (and on some components inside the TV set). Let the condensation evaporate before switching the TV set on again.
this reason, keep the mains and aerial sockets accessible so they can be disconnected, if necessary. Unplug the TV set immediately if you notice it giving off a smell of burning or smoke. You must never, under any circumstances, open the TV set yourself, as you run the risk of an electric shock in doing so.
TV screen The TV screen used in this product is made of glass. Therefore, it can break when the product is dropped or impacted upon by other objects. The TV screen is a very high technology product, giving you finely detailed pictures. Occasionally, a few nonactive pixels may appear on the screen as a fixed point of blue, green or red. This does not affect the performance of your product.
Care Use a glass-cleaning product to clean the screen and a soft cloth and mild detergent to clean the rest of the set. Important: Using strong detergents, alcohol-based and abrasive products may damage the screen. Dust the vents at the back and sides regularly. Using solvents, abrasive or alcohol-based products could damage the TV set. If an object or liquid enters the appliance, unplug it immediately and have it checked by an authorized engineer. Never open the appliance yourself since this may put you at risk or damage the appliance.
WARNINGS This appliance is intended for domestic household use only and should not be used for any other application, such as for non-domestic use or in a commercial environment. If the external flexible cable or cord of this product is damaged, it shall be replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard. Leave more than 10cm clearance around the television to allow adequate ventilation. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.
Hanging the TV set on the wall
To prevent the spread of fire, keep candles or other open flames away from this product at all times.
Eye Fatigue When using this product as a computer monitor, health and safety experts recommend short frequent breaks rather than occasional longer breaks. For example a 5-10 minute break after an hour of continuous screen work is considered to be better than a 15 minute break every 2 hours. Do not use the monitor against a bright background or where sunlight or other bright light sources will shine directly onto the screen. The or POWER/ button on the TV set or the button on the remote control can be used to switch it on and put it into standby mode. If you are not going to be watching the TV for a lengthy period of time, switch it off completely by removing the plug from the mains power socket. During thunderstorms, we recommend that you disconnect the TV set from the mains and aerial so that it is not affected by electrical or electromagnetic surges that could damage it. For
Placing the TV on a table and other surfaces Before setting up your television set, make sure that the surface you want to put the set on can support its weight. Do not place the set on an unstable surface (e.g. moving shelf, very edge of a unit) and make sure that the front of the television set does not overhang the surface it is standing on. To avoid TV from falling please fasten TV to the wall by using necessary screws (in Vesa wall mount holes), clamps, anchors to be bought separately. Install TV near to the wall to avoid falling backwards.
Multi product user manual The features described in this manual are common to most models. Some features may not be available on your TV and/ or your TV may include features that are not described in this user manual. The illustrations in this manual may differ from the actual product. Please refer to the actual product.

Information for Users on Disposal of Old Equipment and Batteries
[European Union] These symbols indicate that the electrical and electronic equipment and the battery with this symbol should not be disposed of as general household waste at its end-of-life. Instead, the products should be handed over to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for proper treatment, recovery and recycling in accordance with your national legislation and the Directive 2002/96/EC and 2006/66/EC. By disposing of these products correctly, you will help to conserve natural resources and will help to prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of these products. For more information about collection points and recycling of these products, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
The sign Pb below the symbol for batteries indicates that this battery contains lead.
[Business users] If you wish to dispose of this product, please contact your supplier and check the terms and conditions of the purchase contract.
[Other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to dispose of these items, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical equipment and batteries.
Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.
TCL Operations Polska Sp. z o.o. ul. A. Mickiewicza 31/41 96-300 Żyrardow, Poland Email address: zyeee@tcl.com
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.
Products · Battery



Connect the power and antenna
To switch on TV after connecting power cord, press or POWER/. Note: Position of power socket varies according to TV model. On certain models, you have to turn on the power

switch first.
-- Position of TV ports varies according to TV model. DVD player, home theatre system, PC
-- It is recommended to use as short as possible high quality HDMI cables to avoid possible interferences. -- It is recommended to use 1m long or shorter VGA cable with ferrite beads in case VGA input is available
in TV and TV is connected using VGA cable. Maximum supported VGA resolution is 1024x768/60Hz.


DVD recorder, headphones, cable receiver
-- Excessive sound pressure from earphones and
headphones can cause hearing loss.
Blu-ray Disc player, HD game console & HD camcorder
-- USB connectors are for data input from USB drives
and for connecting other relevant USB devices where applicable. -- All USB devices have to be directly connected to
TV set without cable extenders. In case extender is required it has to be as short as possible and equipped with ferrite beads. -- ARC (Audio Return Channel) function is only
supported on HDMI3 (ARC) port. -- Number of USB ports may vary.
-- Not all connections available on all models. -- The location of the power socket on the TV may vary according to TV model. -- The positions and names of the function buttons and connectors on the TV may vary
according to TV model.

Remote control functions
Most of your television's functions are available via the menus that appear on the screen. The remote control supplied with your set can be used to navigate through the menus and to configure all the general settings. Note: You are recommended to use the full screen mode. Do not use the display mode with black bars on both sides of the picture (such as 4:3) for a long time; otherwise the TV screen may be damaged permanently.
3D To toggle among the 3D input format options.
Standby / quit standby.
TV To access TV mode.
Alphanumeric buttons To enter channel numbers; to enter a letter, a digit or a symbol in some functions.
SOURCE To select connected devices.
ECO To select desired power saving mode.
V+/- To control the volume.
To switch the sound off and back on.
INFO To display programme information, if
P+/- To change channels.
available.
GUIDE To toggle the Electronic Programme Guide on or off (only available for digital channels).
SMART TV To display the Smart TV homepage.
OPTION To display the function menu to perform
certain operations; to display the Teletext page in different modes.
To navigate through the menus; to set functions and change values.
To navigate through the menus; to select menu options; to switch to the previous or next photo, song or video in USB function.
MENU To access the main menu; to return to
OK To confirm an entry or selection;
To return to the previous menu
ZOOM-/ZOOM+ To select the picture format.
EXIT To exit the menu structure or Teletext.
To operate in some Smart TV applications. @/
SLEEP To toggle among the sleep timer options.
LIST To display the channel list. FAV To bring up the Channel list selection menu.
PRE-CH To return to the previous channel.
Colour buttons To select tasks or Teletext pages. The red button can also be used for MHEG
TEXT To toggle Teletext on or off.
and HbbTV function.
SUBTITLE To select a subtitle language available for selected digital TV programme.
LANG To select a sound type available for selected analogue TV programme; to select an audio language available for
To select the next photo, music or video.
selected digital TV programme.
To select the previous photo, music or
To start fast forward.
video.
To start or pause playback.
To start fast reverse.
Recording button.
To stop playback.
◄/► · ▲/▼ · the previous menu;

Important: Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Remove batteries when the remote control is not to be used for a long time. Batteries left in equipment may cause damage through deterioration and corrosive leakage, invalidating the guarantee. To protect the environment use local recycling facilities for battery disposal. Dispose of used batteries according to the instructions. CAUTION: Risk of explosion if batteries are replaced by an incorrect type. Replace only with the same or equivalent type recommended by the equipment manufacturer. If the batteries in your remote control are run down, you can use the buttons on your TV set. In TV mode, they have the same functions as the corresponding buttons on the remote control. The OK button on the TV set can be pressed repeatedly to select the required source. In the menus they have the following functions:
For models with OK button on the set: For models without OK button on the set: PR+ or PR ▲ ▲ PR+ or PR ▲ ► PR- or PR ▼ ▼ PR- or PR ▼ ◄ & OK VOL+, + or VOL ► ► VOL+, + or VOL ► ▲ VOL-, - or VOL ◄ ◄ VOL-, - or VOL ◄ ▼ MENU or MENU MENU or MENU OK OK
1. When the power cord is connected, the TV will be turned on directly or be in standby mode. If the TV is in standby mode, press the or POWER/ button on the set or the button on the remote control to turn it on. 2. To put the TV into standby mode, press the or POWER/ button on the set or the button on the remote control. The TV set remains powered up, but with low energy consumption. 3. To switch the TV off, unplug the mains plug from the mains outlet.
(*On certain models, you have to turn on the power switch first.)

Initial setup
-- If you select Advanced, use the numeric
Initial setup involves selecting all the settings required to be able to search for and store all the analogue and digital channels you can receive. Make sure that the television is switched on and follow all the steps in turn specified hereafter. Note: If the channel search retrieved only the
analogue channels it could be caused by poor broadcasting and therefore is not covered by manufacturer warranty. Manufacturers cannot be held responsible for lack of or poor broadcasting in some areas.
The first time you switch the set on, the Initial setup wizard opens, which guides you through the initial setup process. (Refer to Figure 1.)
being interrupted, wait for the message indicating that the setup is complete. 4. Before starting the scanning, you can also select Skip scan to skip the initial setup process. In this case, to search and store your channels you may do an automatic channel search by following the instructions in the next section Performing an automatic channel search. 5. During the setup, you can follow the hints available at the bottom of the screen to return to the previous step by pressing ◄. Or press EXIT to exit or interrupt the search halfway. 6. -- In this step, you can press OK to exit the initial
the Password setting menu here in order to set a password. Use the alphanumeric buttons to enter a four-digit number for your password. (0000 is too simple to be set as your password.) Re-enter the same code to confirm the password. After that, you will enter the next step automatically. (In this step, you can only press ◄ to return to the previous step.) 3. Press ▲/▼ to select your tuner mode Antenna or Cable or Satellite. (Note: Satellite option may not be available for certain models.) Then follow a) or b) or c) below.
setup. The channels are arranged in a preset order. If you wish to skip channels, modify the preset order or rename channels, select Setup > Organiser and press OK/► to enter. -- In this step, you can also press ◄ to return to the
previous step.
This section describes how to search and store channels automatically. Instructions are for both analogue and digital channels. This may be done in any of the cases below:
-- you have selected Skip scan in the Initial setup -- you see “Please scan channels!” in TV mode -- you want to update your channels. 1. Press MENU on the remote control and select Settings > Setup > Language. Press ◄/► to select your desired menu language. 2. Press MENU to return to Setup, press ▲/▼ to select Country, then press ◄/► to select your country. The TV installs and arranges channels
-- Press ▲/▼ to select Scan, then press OK/►. -- Press ◄/► to select the scan mode if
available (Full or Advanced). -- If you select Full, press OK to start the
automatic search for all DVB-C digital and/or analogue channels.

according to your country. At this step, you will be requested to enter your password. 3. Press ▲/▼ to select Tuner mode, then press ◄/► to select Antenna or Cable or Satellite. (Note: Satellite option may not be available for certain models.) Then follow a) or b) or c) below.
Accessing channels
Using the alphanumeric buttons: press the corresponding alphanumeric buttons to access the channels. Using the PR+/- or P+/- buttons: scroll through the channels.
Repeatedly press SOURCE on the remote control or OK on the TV set to toggle between TV and other input sources. To resume TV viewing, press any numeric button to enter the channel, while P+/- will cycle through all TV channels and other input sources.
Volume control: use the VOL +/- or VOL ◄/► buttons on the TV set or V+/- buttons on the remote control to increase or decrease the volume. Sound mute: press the button to temporarily mute the sound. Press this button again or the V+ button to restore it.
press OK/► to enter. Select your scan mode if available and configure proper cable information in the same way as in Initial setup. Press ▲/▼ to select Scan and press OK/► to start your automatic search relating to all DVB-C digital and analogue channels. -- If you select Digital, then follow the same
process as above to start your automatic search relating to all DVB-C digital channels. -- If you select Analogue, then press OK/►
1. Press MENU to display the main menu. (Refer to Figure 3.) 2. Press ▲/▼/◄/► to select the desired item, then press OK to open the corresponding submenu. 3. In submenus, use ▲/▼ to select menu options, use ◄/► to set functions or change values. Use OK to activate a setting. Use OK/► to open the corresponding submenu. 4. Press MENU to return to the previous menu. 5. Press EXIT to close the menu. Note: Some options may not be available for
to start your automatic search relating to all analogue channels. -- c) If you have selected Satellite.
certain signal sources.
You can choose your preferred menu language following the instructions below.

2. 3D Mode: Wear the 3D glasses first, then press ◄/► to select the right 3D input format among Top and Bottom, Side-by-Side, 2D-to- 3D, Line interleave and Frame sequential for the playing 3D video. 3. L-R Switch: Select On or Off to adjust the 3D video between the left and right eyes for better 3D viewing. 4. Depth of Field: Achieve a good 3D effect with the image converted from the 2D image. 5. 3D-to-2D: Select Left or Right to display the image in 2D mode (no 3D effect). This function is deactivated when 3D Mode is set to 2D-to-3D or Off. 6. Press EXIT to close the menu. Notes:
You can create a list of your favourite TV channels.
-- 3D glasses from other manufacturers may not be
supported. -- All photo functions are disabled in 3D mode. -- If you change to a different signal source
Shortcut operation: Press FAV on the remote control to directly enter Channel list selection.
or access Smart TV, the 3D mode will be automatically disabled. -- Some 3D modes may not be available depending
on the input format of the 3D video source. -- Supported 3D modes:
Analogue TV, AV, CMP: 2D-to-3D Digital TV, HDMI, USB, Videos from the Internet: Top and Bottom, Side-by-Side, 2D-to-3D, Line interleave, Frame sequential. -- 3D function in USB mode: During the playback
Shortcut operation: Press ECO on the remote control to select a desired power saving mode directly.
of a selected video from USB, press MENU to display the video menu in the browser mode, then select 3D Mode. For more detail information, refer to the above related descriptions.
Viewing TV using the 3D function (* not available for some models)
Audio description refers to an additional narration track for blind and visually impaired viewers of visual media, including television programmes and movies. The description narrator talks through the presentation describing what is happening on the screen during the natural pauses in the audio (and during dialogue if deemed necessary). You can use this feature if the current broadcast contains audio description.

PAP function Use this function to display the pictures from different source inputs side by side. Note that one window is for both analogue and digital TV inputs, the other is for VGA, HDMI and CMP inputs. (Note: Not available for AV on both windows.)
Press MENU on the remote control and select Settings > Teletext > Decoding page language. Select a proper type of language in which Teletext will display.
1. Press MENU to display the main menu. 2. Select Picture and press OK to enter. 3. Press ▲/▼ to select the PAP option, and press OK to enter. 4. Press ◄/► to turn on/off PAP function. 5. Select TV position, press ◄/► to reposition the TV window. 6. Press EXIT to close the menu. If you switch on the PAP function, you can press ◄/► to toggle the focus window. When the focus is on the TV window, the alphanumeric buttons and P+/- work in TV mode. When the focus is on the other window, P+/- switches available external sources.
On digital TV channels, depending on the broadcaster, you may be able to enjoy a service with multiple initial Teletext pages in different languages. This function allows you to select an available language as primary language, which relates to different initial Teletext pages. Press MENU on the remote control and select Settings > Teletext > Digital teletext language. Press ◄/► to select.
Connect the TV to an audio device through the SPDIF output. To select a proper sound type for your SPDIF output, press MENU on the remote control and select Settings > SPDIF type.
You can enable subtitles for each TV channel. Subtitles are broadcast via Teletext or DVB-T/DVB-C digital broadcasts. With digital broadcasts, you have the additional option of selecting a preferred subtitle language.
-- If you select PCM, the SPDIF output format is PCM,
the audio device connected to the SPDIF output.
the programme you are watching. If you select PCM and the sound is ahead of the picture, you can select SPDIF delay from the Settings menu and press ◄/► to adjust the delay time to synchronize the sound with the picture.
Enabling subtitle languages on digital TV channels
Use this function to search for CEC devices connected to the HDMI sockets in your TV and enable one-touch play and one-touch standby between CEC devices.
Enabling or disabling T-Link
Shortcut operation: Press SUBTITLE on the remote control to directly select a subtitle language available for the selected digital TV programme.
Selecting a subtitle type on digital TV channels
With one-touch play, pressing the play button on (for example) your DVD remote control starts playback on your DVD device and automatically switches your TV to the correct source, displaying DVD content.
Turning on/off subtitles · Using one-touch play

This menu option is only available if the common interface module is correctly inserted and activated. On-screen applications and content are provided by your digital TV service operator.
With system standby, pressing the button on (for example) your TV remote control switches your TV and all connected HDMI devices to standby mode.
connected and it is possible that some devices may not interoperate correctly when connected to this TV. The user manual or the manufacturer of the problematic devices should be consulted for further information.
upgrade is completed. Press MENU on the remote control and select Settings > Software update. Press OK/► to enter.
the latest software version from the Internet. Make sure to set up a wired or wireless network connection first then select By network and press OK/► to enter. When new-version software is available, a progress bar appears. When the download finishes, the TV will go black and upgrade the software.
Press MENU on the remote control, then select Settings > Network update. Select On/Off to enable or disable the Network update function.
-- When this function is on, the TV will automatically
update channels if your DTV service provider updates their DTV network. -- When this function is off, you need to run the
channel search again to get new channels or remove unavailable channels if your DTV service provider adds or removes channels from their DTV network.
of the software if available from the broadcast. Use ▲/▼ to select By Channel and press OK/► to enter.
Encrypted digital TV channels can be decoded with a common interface module and a card provided by a digital TV service operator. The common interface module may enable several digital services, depending on the operator and services you choose (for example, pay TV). Contact your digital TV service operator for more information about services and terms.
Using the common interface module
Commission 2009/125/EC, in Home mode, TV will be put into standby mode automatically if there is no operation in 4 hours. This feature can be deactivated in Settings menu.
module from the slot. Removing the module will deactivate the digital services.
Accessing common interface services
After inserting and activating the common interface module, press MENU on the remote control and select Settings > Common interface.
Some digital TV broadcasters offer dedicated digital text or interactive services (for example, BBC1). These services work like normal Teletext with the addition of number, colour and navigation buttons.
Using system standby

or rotate the photo, select different play modes and display effects, etc. 6. Press the related buttons on the remote control to perform the available functions shown on the function bar at the bottom of the TV screen. Press the INFO button to show or remove the function bar.
and cannot coexist on the same screen. If Subtitle is set to On, MHEG will not appear. Please follow the instructions in the section Turning on/off subtitles to set Subtitle to Off. 1. Press the red button or TEXT on the remote control. 2. Press ▲/▼/◄/► to select or highlight items. 3. Press OK to confirm or activate. 4. Press one of the colour buttons to select an option. 5. Press TEXT or EXIT to exit.
Music Use this function to play back music, if available.
Your TV is fitted with a USB connector that enables you to view photos, listen to music or watch videos stored on a USB drive. Supported file formats:
Artist or Album. -- Edit: Copy, paste or delete a selected song. -- Parser: You can select Recursive to display
Photo JPEG Music MP3 Video AVI, MPG, MPEG, TS, DIVX, MKV...
songs from all sub file folders. 3. Select a song, press OK to play, and automatic playback begins from the selected song. Press MENU to display the music menu in the browser mode. You can play or pause the song, select different play modes, etc.
digital cameras or mobile phones are not fully compatible with USB 2.0 standard so they may not work with the TV multimedia player. Not all USB keys or devices are compatible with the USB function. Not all above formats are recognised. The encoding formats of your files will determine whether or not they can be used. When a USB drive is detected, the TV enters the Media center menu directly. To enter the Media center menu manually, press MENU on the remote control and select Media.
songs with lyrics. Select it and use ◄/► to turn on/off lyrics synchronized display. -- Audio only: Select and press OK to listen to the
music with the screen turned off. Any key press will turn the screen on. 4. Press the related buttons on the remote control to perform the available functions shown on the function bar at the bottom of the TV screen.
Video Use this function to watch videos, if available.
Photo Use this function to display photos, if available.
modification Date or Name. -- Edit: Copy, paste or delete a selected video. -- Parser: You can select Recursive to display
videos from all sub file folders. 3. Select a video, press OK to watch, and automatic playback begins from the selected video. Press MENU to display the video menu in the browser mode. You can play or pause the video, select different play modes, screen modes and preset picture settings, etc. 4. Press the related buttons on the remote control to perform the available functions shown on the
Date or Name. -- Edit: Copy, paste or delete a selected photo. -- Parser: You can select Recursive to display
photos from all sub file folders. 5. Select a photo, press OK to watch, and a slide show begins from the selected photo. Press OK to pause the photo. Press MENU to display the photo menu in the browser mode. You can play, pause

function bar at the bottom of the TV screen. Press the INFO button to show or remove the function bar.
product or place of installation. This feature might also be blocked by TV network due to copyright protection (HD content, recording protection). Please use OPTION on the remote control to check if this feature is available in your product. 1. Press MENU on the remote control and select Settings > Setup > Time shift. 2. Press ◄/► to select On to switch on the time shift function, then press EXIT to close the menu. 3. Press OPTION on the remote control and select Time shift, then press OK to confirm. 4. Follow the directions on the screen to do the setup. 5. After the disk setup is done, press OPTION and select Time shift. 6. Press OK to display the time shift menu. -- Press the red button to pause the picture and
DivX video (* not available for some models) ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies.
begin the time shift. -- Press the red button to play the recorded part. -- When the time shift menu disappears and only
the timing of the time shift remains on the screen, you can press the red button or OK to access the time shift menu. -- Press the green button to fast backward or the
yellow button to fast forward. -- Press the blue button to quit the time shift
function.
-- Before you connect the USB drive to the TV,
make sure you have backed up the data in the drive to avoid the loss of your important data due to unforeseen malfunction. -- We recommend you use a USB drive with free
You can access the time from digital channels following the instructions below.
capacity above 1GB and disk speed faster than 5.0MB/sec. -- The bigger the USB drive free memory for time
shift, the bigger the recording length. -- If you change the channel in time shift mode, a
message prompts you to select Yes or No. You can select Yes to exit the time shift function and execute the channel change.
Allows you to reset the TV to factory default settings.
Allows you to record the TV programme so that you will not miss the favourite part even if you go out. Before you use the function, connect a USB drive to the TV first. For the first time, you should do the disk setup for the USB drive.
products and, due to specific TV network limitations and country technical requirements, might not be available in
You can configure your TV according to the equipment you connect to it.

1. Press MENU on the remote control and select Settings > Setup > Input settings. 2. Press OK/► to enter Input settings. 3. Press ▲/▼ to select a connector your equipment is connected to. 4. Press ◄/► to select the type of apparatus attached to this connector. 5. Press MENU to return to the Setup menu. After configuring, the selected source label will be displayed after the name of the related connector in the source list when pressing SOURCE on the remote control or OK on the TV set.
Allows you to record your favourite TV programmes. Before you use the function, connect a USB drive to the set first.
products and, due to specific TV network limitations and country technical requirements, might not be available in product or place of installation. This feature might also be blocked by TV network due to copyright protection (HD content, recording protection). Please use OPTION on the remote control to check if this feature is available in your product. 1. Press OPTION on the remote control and select Quick access > PVR. 2. Press OK/► to enter. 3. Press: -- the red button to start recording, the record file is
EPG is an on-screen guide that displays scheduled TV programmes. You can navigate, select, view and record programmes.
1. Press GUIDE on the remote control, the Now and Next EPG menu will appear, which allows you to get information about the current or next programme playing on each channel. Navigate through the different programmes using the navigation buttons on the remote control. 2. Use the colour buttons to view the 8 Days EPG. -- Prev day (Red): List the previous day’s EPG. -- Next day (Green): List the next day’s EPG. -- View detail (Yellow): Display the description of
put into a folder named after the channel number under the PVR folder in Media > Video; -- ▲/▼/◄/► to adjust the recording duration. -- the green button to stop recording manually;
in normal operation, the recording will stop automatically when the recording duration has passed. 4. In recording, PVR mini pane will also show on the screen to indicate the recording progress. 5. To watch the recorded programme, exit PVR mode first and go to Media > Video. Select the folder PVR, then select the related record file. Press OK to play. (It is the same if you record a digital radio programme).
this programme if available. -- Type filter (Blue): Programme guide filter for
-- This feature is available only for non encrypted
digital channels. Even when CICAM (CI or CI+) is inserted, this feature is not available on encrypted channels. -- Before you connect the USB drive to the set,
make sure you have backed up the data in the drive to avoid the loss of your important data due to unforeseen malfunction. -- The bigger the USB drive free memory for the
PVR function, the bigger the recording length. -- If you want to change channel or signal source
during recording, store the recording data before changing the channel or source. -- The set cannot play files normally if the
remote control to bring up the Schedule list menu. For details on scheduled recording, refer to the Schedule list section. 3. Press GUIDE/EXIT to exit the EPG and switch to the selected channel.
parameters of the file exceed the limitations of the system, the file format is not supported, the file is damaged, or the file cannot be decoded. -- Do not disconnect the USB drive when the
system is reading a file or transmitting data, otherwise the system or the drive may be damaged.

Schedule list
the wall outlet is attached to a modem or router elsewhere in your house. 1. Press MENU on the remote control and select Network > Network settings > Internet connection. Press ◄/► to select On. 2. Press ▲/▼ to select Interface, then set ◄/► to Ethernet to select wired-mode connection. 3. Press ▲/▼ to select Connection test, then press OK/► to check the Internet connectivity. If it does not work, follow step 4 below. 4. Select Network > Network settings > IP setting, then press OK/► to enter the IP setting menu. You can set Address type to Auto or Manual.
This function is used to perform scheduled recording.
channel number. -- Start date: use the alphanumeric buttons to set
the recording date. -- Start time: set the starting time of the recording. -- Stop time: set the stopping time of the recording. -- Schedule type:
-- Select Auto if you want the TV to acquire and
enter the needed IP address automatically. -- Select Manual if you want to enter your IP
press MENU to go back, press ▲/▼ to select Connection test, then press OK/► to check the Internet connectivity again. 5. If you want to see the information on current connection, such as Interface, Address type, IP address, etc., select Network > Network settings > Information, then press OK/►.
recording. 4. Press ▲/▼/◄/► to select Add, then press OK to add the schedule you set into your schedule list. 5. Press the red button to repeat above procedures to add another schedule. 6. If you wish to edit or delete a schedule, select it and press OK to enter. 7. Press EXIT to close the menu.
Connecting to a wireless network To connect your TV to your network wirelessly, you need a wireless router or modem and a Wireless LAN Adapter (some TV models are equipped with an integrated LAN Adapter). Connect your Wireless High-Gain USB Adapter (USB dongle) delivered with your TV to your TV’s USB 1 port.
Network connection
You can set up your TV so that it can access the Internet through your local area network (LAN) using a wired or wireless connection.
Connecting to a wired network

3. Make sure the laptop and the TV are in the same home LAN (local area network) or network segment. 4. Run the TV Remote application on the laptop, it will search and communicate with the TV automatically to enable the TV Remote functionality. 5. Once the TV and the laptop are linked as described in step 4, you will be able to enjoy the extra features of the TV Remote function. 6. To quit the TV Remote function, press EXIT on the remote control.
-- If you select a protected access point, you will
have to enter the corresponding password. Press OK on the remote control to display the virtual keyboard to enable you to enter the password. -- This set is able to memorize the available
access point, which enables it to connect to the network even if you switch on your TV after power-off. -- b) Manual
Press ▲/▼ to select Manual, then press OK/►, you will be prompted to enter the correct SSID of an available wireless router to set up the connection. -- c) Auto
Share & See or DLNA function. Share & See is DLNA-compatible.
Make sure to set up a wired or wireless connection from your TV to a router first. Then connect your PC to your router either through a network cable or wirelessly. Also make sure to select Network > Network settings > Internet Connection, then On, and that your computer firewall won’t block the connection.
Select Network > DLNA, and set it to On. Follow the steps in turn specified hereafter, then you can enjoy recorded video, image and music saved on your PC.
Install a DLNA media server on your PC. The simple and familiar server you may install is Microsoft Windows Media Player 11 and 11 above. Follow the instructions below to allow your TV to access the designated files on your PC.
PC. -- Select Allow to allow the TV set to access your
This function allows you to turn a smart device into a sophisticated remote control, providing more features than your normal TV remote control. You can then control your TV through your smart device.
PC, and select OK to enable the access. Note: Use the Settings button to customize your
desired settings. 2. -- Select Library > Add to Library. -- Select your personal folders or folders of other
users that you can access for sharing. -- Select Add and press OK to enable the addition.
Select Media in the main menu and press OK to enter media center. Then you can view photos, listen

to music or watch videos, which are stored on your PC.
1. Press MENU on the remote control, then select Settings > HbbTV mode. 2. Press ◄/► to select On. 3. When you tune to a TV digital channel that offers HbbTV, this will be signalled to you by an on- screen indication (generally a red button, but other colour buttons may also be used). Press the indicated colour button to open the interactive pages. 4. Use ▲/▼/◄/► and the colour buttons to navigate through the HbbTV pages and press OK to confirm.
-- If DLNA is switched on, the TV will display the
list of available DLNA servers which are available in local network. -- Supported file formats:
HbbTV (Hybrid broadcast broadband TV) is a service offered by certain broadcasters and available only on some digital TV channels. HbbTV delivers interactive television over both broadcast and broadband Internet. These interactive features are added to and enrich the normal digital programmes, and include services such as digital teletext, electronic programme guide, games, voting, specific information related to the current programme, interactive advertising, information magazines, catch-up TV, etc. There are two modes:
To avoid disturbances that may be caused by HbbTV broadcasting tests, you can turn off the HbbTV function:
Allows you to enjoy Internet Applications (Apps), specially adapted Internet websites for your TV. You can control the Apps with the TV remote control.
-- In the broadcast mode, your TV does not need to
be connected to the Internet. You will be able to receive those HbbTV services broadcast at the same time as the programme being watched, such as specific and additional information related to the programme. An on-screen indication (for example, red button) will invite you to press the red button on your remote control to access the service.
Figure 6 (source: ETSI) gives such an example.

Figure 6 -- In the broadband mode, your TV has to be connected
to the Internet. In addition to the broadcast programme being watched, you can access the same services as in broadcast mode and also many other Internet-delivered interactive services such as VOD (Video On Demand) or catch-up TV.
Figure 7 (source: ETSI) gives such an example.

Shortcut operation: Press Smart TV on the remote control to display the smart TV home page directly. 2. Use ▲/▼/◄/► to select an App and press OK to enter. 3. Internet browsing is available with Smart TV portal application. It can be accessed via the icon in the
Figure 7 To fully enjoy HbbTV, you need to connect your TV to the Internet (refer to section Network connection).
this function.

portal or via the green button when TV portal page is displayed. Note: Since the connection with internet takes
time, it’s recommended that you wait a few minutes to use the smart TV feature after activation of TV from standby.
Make voice calls and video calls with Skype on your TV.
No emergency calls with Skype
Made possible by Smart TV - bringing useful and entertaining features directly from the web to your TV.
Skype is not a replacement for your ordinary telephone and can’t be used for emergency calling.
Skype is a trade mark of Skype Limited or its related companies. This product/application has not been approved or endorsed by Skype Limited, Skype Communications S.a.r.l. or any of their related companies.
This product includes SkypeKit Version [4.5] Copyright 2003-2013, Skype Limited Patents Pending Skype, associated trade marks and logos are trade marks of Skype Limited.
Password in Parental Control
-- The default password is 1234. You can change it to
a new one. -- The super password is 0423. If you forget your
code, enter the super password to override any existing codes.
Please check the following list before requesting service.

LGPL software: DFB, SAWMAN, ALSA.
[Legal Statement] of TCL - manufacturer of this TV set. Due to the various capabilities of products featuring the SmartTV - Services, as well as limitations in the available content, certain features, applications, and services may not be available on all devices or in all territories. Some features on SmartTV may also require additional peripheral devices or membership fees that are sold separately. Please visit our website for more information on specific device information and content availability. The services and availability of content through SmartTV are subject to change from time to time without prior notice.
All content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal noncommercial use. You may not use any content or services in a manner that has not been authorized by the content owner or service provider. Without limiting the foregoing, unless expressly authorized by the applicable content owner or service provider, you may not modify, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or distribute in any manner or medium any content or services displayed through this device.
TV Broadcasting PAL/SECAM BG/DK/I/LL’ Receiving channels VHF/UHF/Cable Tuner type Frequency synthesized
Operating Conditions Temperature 5°C - 35°C (41°F - 95°F) Humidity 20 - 80% (non-condensing)
YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT USE OF THE DEVICE IS AT YOUR SOLE RISK AND THAT THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE AND ACCURACY IS WITH YOU. THE DEVICE AND ALL THIRD PARTY CONTENT AND SERVICES ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED. TCL EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS WITH RESPECT TO THE DEVICE AND ANY CONTENT AND SERVICES, EITHER EXPRESS OR, IMPLIED, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY, OF SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, OF ACCURACY, OF QUIET ENJOYMENT, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. TCL DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS OF ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND DOES NOT WARRANT THAT THE DEVICE, CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS, OR THAT OPERATION OF THE DEVICE OR SERVICES WILL BE UNINTERRUPTED OR ERROR-FREE. UNDER NO CIRCUMSTANCES,
Storage Conditions Temperature -15°C - 45°C (5°F - 113°F) Humidity 10 - 90% (non-condensing)
This product uses some software programs which are distributed under the Independent JPEG Group. This product uses some software programs which are distributed under the Freetype Project. This product uses some software programs which are distributed under the OpenSSL Project. This product uses some software programs which are distributed under the zlib license. This product uses UNICODE software programs which are distributed under IBM Open source license. This product uses libpng software programs which are distributed under OSI Certified Open source license. This product uses Expat, Libcurl, c-ares software programs which are distributed under MIT license. This product uses some software programs which are distributed under the GPL/LGPL. GPL software: Linux Kernel, Busybox, SquashFS, mtd-utils, e2fsprogs, BlueZ, Dbus, Glib, NTFS-3G Read/Write Driver, samba, iconv, Linux File System FTA.

INCLUDING NEGLIGENCE, SHALL TCL BE LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR AS A RESULT OF THE USE OF THE DEVICE, OR ANY CONTENT OR SERVICE ACCESSED BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Third party services may be changed, suspended, removed, terminated or interrupted, or access may be disabled at any time, without notice, and TCL (manufacturer of Thomson branded TVs) makes no representation or warranty that any content or service will remain available for any period of time. Content and services are transmitted by third parties by means of networks and transmission facilities over which TCL has no control. Without limiting the generality of this disclaimer, TCL expressly disclaims any responsibility or liability for any change, interruption, disabling, removal of or suspension of any content or service made available through this device. TCL may impose limits on the use of or access to certain services or content, in any case and without notice or liability. TCL is neither responsible nor liable for customer service related to the content and services. Any question or request for service relating to the content or services should be made directly to the respective content and service providers.
is a trademark of SRS Labs, Inc.
TruSurround HD technology is incorporated under license from SRS Labs, Inc.
SRS TruSurround HD™ creates an immersive, feature-rich surround sound experience from two speakers, complete with rich bass, high frequency detail and clear dialog.
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.