
used, as for non-domestic use or in a commercial environment.
Make sure that the voltage of your power grid matches the voltage indicated on the type plate at the back of your TV device. If the power plug, AC input or device connector is used to disconnect this product from the supply, it must always be accessible and ready.
If the external flexible cable or cord of this product is damaged, it must be replaced by the manufacturer, a maintenance representative of the manufacturer or by a similarly qualified person to prevent any danger.
Allow more than 10 cm of space around the television to allow sufficient ventilation. Ventilation shall not be hindered by covering the ventilation vents with objects such as newspapers, tablecloths, curtains etc.
On certain models the indicator light is located on the side of the TV. When the indicator lamp is off at the front, this does not mean that the TV device is completely disconnected from the power grid. To completely disconnect the TV device, pull the plug.
The apparatus must not be exposed to dripping or splashing water and no objects filled with liquids, such as vases, shall be placed on the product.
The parts of the TV are heat sensitive. The maximum ambient temperature shall not exceed 35° Being Celsius. Do not cover the ventilation openings at the rear or sides of the TV set. Leave enough space around the TV for good ventilation. Place the device away from heat sources (fireplaces etc.) or devices that produce strong magnetic or electronic fields.
Batteries (installed battery block or installed batteries) must not be exposed to too much heat, such as sunlight, fire etc.
Never expose this device to rain or moisture, in order to avoid the risk of fire or electric shocks.
Never place the television on an unstable surface. A television can fall over and cause serious or fatal injury. Many injuries, especially of children, can be prevented by taking some simple precautions:
The humidity in rooms where the TV device is installed, it shall not exceed 75%. Moving the TV from a cold to a warm room can cause condensation on the screen (and on some parts in the TV set). Let the condensate evaporate before you turn on the TV device again.
The . .POWER/ • The TV-set or the • • remote control button can be used to turn on and switch the TV-setting device into standby mode. If you are not sure, Long time doesn't watch TV, then turn it off completely by removing the plug from the socket.
We recommend that you during Thunderstorms to remove the plug from the socket (including antenna) so that the TV device is not affected by electrical or electromagnetic peaks capable of causing damage. This is why electrical sockets and antenna connections to keep them accessible so that they can can be decoupled, if necessary.
Unmount the TV device immediately if you have a burning odour or Smoke Sensors. You may never, in any circumstances, open the TV set itself because you are at risk of having a electric shock walk when you do.
Equipment with this symbol is a Class II or double insulated electrical device. It is designed to avoid requiring a secure connection to electrical mass. Equipment without this symbol is a Class I electrical device. This type of device must be connected to an electrical outlet with a protective mass connection.
This apparatus is for domestic use only and must not be used in any other way.
Security

To prevent fire, keep candles or other open flames away from this product at all times.
To prevent injury, this device must be safely secured against the floor/wall in accordance with installation instructions.
The TV screen used in this product is made of glass. It can therefore break if you drop the product or have it taken from other objects.
User's manual for multiple products
The TV screen is a product with highly advanced technology and provides an extremely detailed view. Sometimes some inactive pixels appear on the screen as a fixed blue, green or red dot. However, this will not affect the performance of your product.
The functions described in this manual are common to most models. Some features may not be available on your TV and/or your TV may contain functions that are not described in this user manual. The illustrations in this instructions for use may differ from the real product. Consult the real product.
Use a glass cleaner to clean the screen and soft cloth and mild cleaning agent for the rest of the TV set.
Dust the vents at the back and sides regularly. Solvents, abrasive or alcohol-based products can damage your TV device. If an object or liquid enters the device, immediately remove the plug from the socket and have it checked by an authorized repairman. Never open the device yourself as you may be in danger or damage the device.
This device meets ESD performance criteria. If the device is not restored to ethernet connection mode due to electrostatic discharge, action shall be taken by the user.
Hanging the TV device on the wall
To ensure a safe installation, please observe the following safety instructions:
TV screen · Care · ESD requirements

Information for users on the disposal of old equipment and batteries
These symbols indicate that the electrical and electronic equipment and battery with this symbol at the end of its life cycle should not be disposed of as ordinary household waste. On the other hand, products should be submitted to specific collection points for recycling electrical and electronic equipment as well as batteries, for proper treatment, recovery and recycling in accordance with your national legislation and Directive 2012/19/EU, 2006/66/EC and 2008/12/EC.
By removing these products correctly, you will contribute to the conservation of natural resources and help prevent potential negative effects on the environment and public health that could otherwise be caused by improper waste treatment of those products.
Notification:
For more information about collection points and recycling of these products, please contact the municipal office, the department responsible for disposal of your household waste or the shop where you bought the product.
The symbol "Pbb' under the symbol for batteries indicates that this battery contains lead.
Penalties may apply for improper disposal of such waste in accordance with national law.
If you wish to remove this product, please contact your supplier and check the terms and conditions of the purchase agreement.
[Other countries outside the European Union]
These symbols are only valid in the European Union. If you wish to remove these articles, do so in accordance with applicable national law or other rules in your country for the treatment of old electrical equipment and batteries.
TCL hereby declares that this apparatus is in conformity with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.thomsontv.eu
The images and illustrations in this manual are purely for reference purposes and may differ from the actual product in appearance. Product design and specifications may be modified without prior notice.



To switch on the TV after connecting the power cord, press or POWER/ .
- The location of the power supply varies according to TV model.
- Remove the plug from the socket before connecting devices.


Antenna/Cable Satellite SPDIF HDMI 1 (ARC) HD MI 2 AV adapter
-- Not all connections are available on all models. -- The position and names of the function buttons and connections on the TV may vary depending on the
TV model. -- Before connecting a PC, you must set the monitor's refresh rate to 60 Hz. -- It is recommended to use high quality HDMI cables as short as possible in order to reduce the risk of
to prevent disturbances. -- The ARC (Audio Return Channel) function is only supported on the HDMI port identified with ARC. -- The USB port is used for data input from USB memory devices. -- All USB devices must be connected directly to the TV set without using extension cables.
In the case of a need for an extension, it should be equipped with ferrite rings as short as possible.
Blu-ray Disk Player

Most of the features of your TV are available via the menus that appear on screen. The remote control provided with your TV can be used to navigate through the menus and configure general settings.

Source To select the connected devices.
End standby. Keyboard keys To enter channel numbers or a digit.
ECO To enable or disable ECO mode. Guide To enable or disable the Electronic Program Guide (only
available for digital channels). Menu To open the main menu; to go back to previous menu
Turn. Exit To close the menu or teletext. ▲▼For navigation in the main menu; for selection of menu options; to
switch between previous or next photo, track or video in USB mode. •► /*Zoom+/-
For navigation in the main menu; for setting functions and changing values. ► can also be used to open the corresponding submenu. * To select the image format. NOTE: It is recommended to use full screen mode. Do not use black beam display mode on both sides of the image (such as 4:3) for a longer period of time, otherwise the TV screen may be permanently damaged. OK To open the corresponding submenu and set a setting
Activate menu menu mounts; to freeze/continue the image in digital TV mode. Option To display the function menu to output certain operations
to display the teletext menu on the tele text page. Return To return to the previous channel or menu.
V+/- To control the volume. Info To display program information, if available. Mute To turn the sound off and back on.
P+/- To change channel. TEXT To switch on or off teletext. SUBTITLE To select a subtitle language available for the
selected digital TV program. LIST To display the channel list.
TV To go to TV mode. Color keys To select tasks or teletext pages.
Long To select an audio language available for the
selected digital TV programs. NOTE: The remote control type can be changed without notice.

Batteries never serve excessive heat, such as sunlight, open flames etc. exposed. Remove the batteries from the remote control if it is not used for a long time. In the equipment left behind batteries can cause damage due to deterioration and corrosive leakage and render the warranty invalid.
Bring exhausted batteries to local recycling companies for battery disposal in order to protect the environment. Remove the batteries as prescribed.
CAUTION: Explosion hazard if batteries are replaced by an incorrect type. Replace only the same or equivalent type recommended by the manufacturer of the equipment.
If the batteries in your remote control are exhausted, you can use the buttons on your TV device. They have the following functions:
For models with the following keys on the device:
For models with the following keys on the device:
Enable/disable the TV
1. When the power cord is connected, the TV will be switched on immediately or in standby mode. In standby mode press the - or POWER/ -button on the TV device or the button on the remote control to turn the TV on. 2. Press the key on the remote to switch the TV to standby. The TV device will then remain on, but with very low energy consumption. 3. You can turn off the TV by removing the plug from the socket.
The first time you turn the device on, the screen appears Hello (Hello) that you are accompanied by the first installation procedure. Follow the on-screen instructions to complete the first installation procedure, such as selecting language, scanning channels and much more. Make a choice for each step or skip one step. If you miss a step, you can set the setting later via the Settings menu.
The Commission has not yet adopted a decision on the basis of Article 85 (3) of the Treaty. Manufacturers cannot be held liable for a weak or non-viable broadcast in certain areas.
V-/◄ Enable/Stand-by · Features (short press) · (long press)

go to the customization interface or its submenu. 5. Press Return to return to the previous menu. 6. Press Exit to close the menu.
With the numerical keys: Press the corresponding number keys of the remote control to open the channels.
Using the P +/- keys: Press the P+/--buttons on the remote control or corresponding buttons on TV to browse through channels.
press the remote control Settings (Settings) to be selected and on OK press to open the setting menu. Some options may not be available for certain signal sources.
Using the LIST key: press the key LIST on the remote control to open the channel list, press ./▼ to select channels and then press for confirmation OK.
Select Menu Language
Select connected equipment by the three methods below:
You can select the desired menu language.
Press again Source or on Exit to leave the menu.
Volume control: Press the V+/--buttons on the remote control or corresponding buttons on TV to increase or reduce the volume.
The noise dampen: Press the Mute-key to temporarily mute the sound. Press this key again or the V+-key to restore sound.
It allows you to customize TV settings, such as image and sound.

The common interface module can allow some digital services depending on the provider and services you choose (e.g. pay TV). Please contact your TV service provider for more information about services and terms.
This chapter describes the automatic search and storage of channels. This may be done in any of the following cases:
-- you have the step for installing channels
Skipped at first installation; -- you get a message that there are no channels in TV
mode; -- you want to update your channels.
1. Press TV mode Menu to open the main menu, use . Settings Select (Settings) and then press OK. Press ./▼ to Channel > Channel Scan (Channel > Channel scan) select and then press OK/► to open. 2. The TV sets and ranks the channels according to your country. Press ./▼ to Country (Country) to select, and press OK/► to open. Enter the default password 1234 or your own password if you changed the password in the menu Settings > Lock >: Change password (Settings > Locking > Change password). Press ./▼ to select your country and press OK to confirm. 3. Press ./▼ to Automatic search Select (Auto-search) and press OK/► to open it. 4. Press ./▼ to Tuner mode Select (Tuner mode) and press . Antenna (Antenne), Cable (Cable) or Satellite (Satellite) (Note: The option Satellite (Satellite) may not be available for certain models.) 5. Press ./▼ to select other configuration options. 6. After the configuration is complete, press ▼ Search Select (search) and press OK To scan channels. 7. The search could take a few minutes. After automatic search, the channels are arranged according to a preset order. If you want to skip channels or set your favorite channels, press the button Menu on the remote control, then press ./▼/ Settings > Channel >: Channel organizer Select (Settings > Channel > Channel Manager) and press OK/► to open.
Not out of the slot. Taking out the module will deactivate digital services. This TV has a CI+ certificate. It is recommended that you use a common interface module with CI+ marking.
After you have placed and activated the common interface module, press Menu on the remote, select Settings > Channel >: Common interface (Settings > Channel > Common interface) and press OK/► to open. This menu option is only available if the common interface module is correctly inserted and activated. On-screen applications and content are provided by your digital TV service provider.
EPG is a guide on the screen to see which digital TV program is planned. You can navigate, select and display the program .
Encrypted digital TV channels can be decoded using a common interface module and a card available via a digital TV service provider.

to view related information. -- Schedule (Programme): press the yellow
button to view your program list. Press the yellow button again to return to the previous menu, press the red button to remove the channel from the program list. -- Brake (Remembrance): Press the blue button
to the menu Set a reminder (Configure a reminder), use . . / . to select a reminder and press OK to confirm. Use . ./► to set a custom reminder. 3. Press Guide or Exit to close the EPG.
You can enable subtitles for any TV channel. Subtitles are broadcast via teletext or DVB-T/DVB-C digital broadcasts. For digital broadcasts, you have the extra option to select your desired subtitle language.
Language of digital teletext
Depending on the broadcasting, it is possible to enjoy a service with multiple first teletext pages in different languages on digital TV channels. This feature allows you to select a available language as the first language for the opening page of Teletext.
Use this feature to search for CEC devices connected to your TV's HDMI connections and enable one-touch playback and one-tuch stand-by between CEC device.

Disable or disable T-Link
in the input source list displayed when you click on the button Source press the remote control or in the main menu when you click Menu press the remote.
Play one touch, playback on your DVD device is started by pressing the remote control of your D VD device (for example) onto the gamegrounds and automatically switching your TV to the right source to display the DV DVd content.
Commission Directive 2009/125/EC will automatically put TV in home mode on standby if no action is taken for 4 hours. Select Settings > Time >: Auto Standby (Settings > Time >: Auto Standby) to disable this function.
With system-standby, your TV and all connected HDMI devices are switched to standby mode by pressing the remote control of your TV on the -key (for example).
-- The CEC functions depend on the
connected equipment and it may happen that correct inter-operation of certain equipment is not possible when connected to this TV. For more information, please refer to the operating manual or manufacturer of problematic equipment. -- You can also press the button Option on the
Use this function to update the software.
Press remote to access T-Link (T-Link).
Adjust input settings
This allows you to reset the TV set to factory settings. 1. Press Menu on the remote control, select Settings > System >: Reset shop (Settings > System > Reset Store) and press OK to open 2. Use the cipher keys to enter the password. 3. Press . . OK select and press OK to start. 4. The screen Hello (Hello) is displayed. Follow the on-screen instructions.
You can configure your TV using the equipment you have connected to it. 1. Press Menu on the remote control, select Settings > System > (Settings > System > Initiating settings) and press OK/► to open. 2. Press ./▼ to choose a connector that your equipment is connected to, press OK/► to open. 3. Press ./▼ to select the type of device connected to this connector and press OK to confirm. 4. Press Exit to close the menu.
After configuring, the selected source label is named after its associated connector

From a USB storage device view photos, play music and watch movies
Your TV is equipped with USB connections that you can use to view photos, listen to music or watch videos stored on a flash drive.
Use this function to view video clips, if available. 1. Select Media > Movie (Media > Film), then press OK to open. 2. After selecting the right disk, press OK to open, then use ./▼/ .to select a video. 3. Press OK to view, and autoplay starts from the selected video. Press Menu to display the video menu. You can play, pause and different playback modes, display modes and image presets etc. select.
-- Some USB drives and USB products such as
Digital camera performances or mobile phones are not fully compatible with the USB 2.0 standard, making it possible that they do not work with the TV multimedia player. Not all USB drives or devices are compatible with the USB function. Not all the above formats are recognized. The encoding format of your files determines whether or not they can be used. -- The format H.265 may not be available
for certain models.
To the menu Media (Media) open, press Source on the remote and select Media (Media). View
Use this function to display photocopiers, if available. 1. Select Media > Picture (Media > Image), and then press OK to open 2. After selecting the right disk, press OK to open and use ./▼/ .to select a photo 3. Press OK to view, a slide show starts from the selected photo. Press OK to pause Press Menu to display the photo menu. You can view, pause or rotate the photo, different display modes and display effects etc. select.
Use this function to play music, if available. 1. Select Media > Music (Media > Music), then press OK to open. 2. After selecting the right disk, press OK to open, use ./▼/ .to select a number.

If the above suggestions do not solve the technical problem, please refer to the warranty card for service information.
-- The default password is 1234. You can use it in
Change a new password. -- The super password is 0423. If you are your code
Forgot, you can enter the super password to overwrite existing codes.
Temperature 5°C - 35°C (41°F - 95°F) Humidity 20-75% (non-condensing)
Check the following list before requesting service.
Temperature -15°C - 45°C (5°F - 113°F) Humidity 10-90% (non-condensing)
Please contact the nearest TCL office for requests and information about open source. This product uses the GPL (version 2 and 3) and LGPL (release 2.1) and MPL (verse 1.1). This product uses a number of software programs that are distributed to the Independent JPEG Group. This product uses a number of software programs that are distributed under the libpng Project. This product uses a number of software programs that are distributed under the Freetype Project. This product uses a number of software programs that are distributed under the zlib Project. This product uses a number of software programs (curl, cares, xml2, pixman, iniparser, fastlz) that are distributed under the MIT. This product uses opensl and xerces that are distributed under SSLey and OpenSSL. GPL software: Linux Kernel, iconv LGPL software; DFB (DirectFB), glib, alsa, neon, pango, qt, glibc, uclibc BSD software: webp, mng, uriparser
Working conditions · Storage conditions · OSS announcement
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.