Instruction/ maintenance manual of the product T55 Bostitch
Go to page of 11
BEFORE OPERA TING THIS TOOL, ALL OPERA TORS SHOULD STUDY THIS MANUAL TO UNDERST AND AND FOLLOW THE SAFETY W ARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE T OOL FOR FUTURE REFERENCE. IF YOU HA VE ANY QUESTIONS, CONT ACT YOUR ST ANLEY -BOSTITCH REPRESENT A TIVE OR DISTRIBUTOR.
INTRODUCTION The Stanley-Bostitch T55 series staplers are precision-built tools, designed for high speed, high volume stapling. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer ’s instructions must be followed.
-3- SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL W A YS be worn by the operator and others in the work area when loading, operating or servicing this tool.
-4- T55 TOOL SPECIFICA TIONS All screws and nuts are metric. F ASTENER SPECIFICA TIONS: TOOL AIR FITTING: This tool uses a free-flow connector plug, 1/4 ” N.P .T . The minimum inside diameter should be .200 ” (5mm). The fitting must be capable of discharging tool air pressure when disconnected from the air supply .
-5- AIR SUPPL Y AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury . FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.
-6- EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL W A YS be worn by the operator and others in the work area when loading, operating or servicing this tool.
-7- EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL W A YS be worn by the operator and others in the work area when loading, operating or servicing this tool.
-8- TOOL OPERA TION CHECK CAUTION: Remove all fasteners from tool before performing tool operation check. 1.TRIGGER OPERA TED T OOL: A. With finger off the trigger , hold the tool with a firm grip on the handle. B. Place the nose of the tool against the work surface.
-9- BASIC TOOL OPERA TION Stanley-Bostitch pneumatic tools are cycled by a compressed air operated single piston design. The following illustrations show the four functional cycles that occur when the.
-10- TROUBLE SHOOTING PROBLEM CAUSE CORRECTION T rigger valve housing leaks air O-ring cut or cracked Replace O-ring T rigger valve stem leaks air O-ring/seals cut or cracked Replace trigger valve ass.
DIRECTIONAL EXHAUST DEFLECTOR Loosen screw as shown. Adjust to desired exhaust direction and tighten screw . -1 1- ACCESSORIES A V AILABLE BC601 4 oz. Stanley-Bostitch Air -T ool Lubricant BC602 1 pin.
An important point after buying a device Bostitch T55 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bostitch T55 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bostitch T55 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bostitch T55 you will learn all the available features of the product, as well as information on its operation. The information that you get Bostitch T55 will certainly help you make a decision on the purchase.
If you already are a holder of Bostitch T55, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bostitch T55.
However, one of the most important roles played by the user manual is to help in solving problems with Bostitch T55. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bostitch T55 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center