

heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.




1 1 1 Induction cooking zone 2 Control panel

Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which functions operate.

1 ON / OFF To activate and deactivate the hob.
To show for which zone you set the time.

7 / - To increase or decrease the time.
8 / - To set a heat setting.
9 Power function To activate and deactivate the function.
The cooking zone is deactivated.
- The cooking zone operates.
Automatic Heat Up function operates.
Power function operates.
+ digit There is a malfunction.
A cooking zone is still hot (residual heat).
Lock / The Child Safety Device function operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off function operates.
the bottom of the cookware. The glass ceramic is heated by the heat of the cookware.
The induction cooking zones make the heat necessary for cooking process directly in
Touch for 1 second to activate or deactivate the hob.
Sen- sor field · Function Comment · Display Description

for some time and then decreases to the correct heat setting.
The function deactivates the hob automatically if:
To activate the function the cooking zone must be cold.
To activate the function for a cooking zone: touch ( comes on). Immediately touch ( comes on). Immediately touch until the correct heat setting comes on. After 3 seconds comes on.
To deactivate the function: touch .
This function makes more power available to the induction cooking zones. The function can be activated for the induction cooking zone only for a limited period of time. After this time the induction cooking zone automatically sets back to the highest heat setting.
comes on and the hob deactivates. The relation between the heat setting and the time after which the hob deactivates:
Refer to “Technical information” chapter.
To activate the function for a cooking zone: touch . comes on.
Heat setting The hob deacti- vates after
To deactivate the function: touch or .
, 1 - 2 6 hours
Count Down Timer You can use this function to set how long the cooking zone should operate for a single cooking session.
First set the heat setting for the cooking zone then set the function.
Touch to increase the heat setting. Touch to decrease the heat setting. Touch and at the same time to deactivate the cooking zone.
To set the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on.
To activate the function or change the time: touch or of the timer to set the time (00 - 99 minutes). When the indicator of the cooking zone starts to flash slowly the time counts down.
If you activate this function you can get a necessary heat setting in a shorter time. The function sets the highest heat setting
5 4 hours

To see the remaining time: set the cooking zone with . The indicator of the cooking zone starts to flash quickly. The display shows the remaining time.
This function prevents an accidental operation of the hob.
To activate the function: activate the hob with . Do not set the heat setting. Touch for 4 seconds. comes on. Deactivate the hob with .
To deactivate the function: set the cooking zone with and touch . The remaining time counts back to 00. The indicator of the cooking zone goes out.
To deactivate the function: activate the hob with . Do not set the heat setting. Touch for 4 seconds. comes on. Deactivate the hob with .
When the time comes to an end, the sound operates and 00 flashes. The cooking zone deactivates.
To stop the sound: touch .
To override the function for only one cooking time: activate the hob with . comes on. Touch for 4 seconds. Set the heat setting in 10 seconds. You can operate the hob. When you deactivate the hob with the function operates again.
Minute Minder You can use this function as a Minute Minder when the hob is activated and the cooking zones do not operate. The heat setting display shows .
To activate the function: touch . Touch or of the timer to set the time. When the time comes to an end, the sound operates and 00 flashes.
To stop the sound: touch .
The function has no effect on the operation of the cooking zones.
You can lock the control panel while cooking zones operate. It prevents an accidental change of the heat setting.
Set the heat setting first.
To activate the function: touch . comes on for 4 seconds. The Timer stays on.
To deactivate the function: touch . The previous heat setting comes on.
When you deactivate the hob, you also deactivate this function.

Induction cooking zones adapt to the dimension of the bottom of the cookware automatically to some limit.
The cooking zone efficiency is related to the diameter of the cookware. The cookware with a smaller diameter than the minimum receives only a part of the power generated by the cooking zone.
For induction cooking zones a strong electro-magnetic field creates the heat in the cookware very quickly.
Refer to “Technical information” chapter.
Use the induction cooking zones with correct cookware.
If you can hear:
The bottom of the cookware must be as thick and flat as possible.
The relation between the heat setting and the cooking zone consumption of power is not linear. When you increase the heat
Cookware material · Cookware dimensions

setting, it is not proportional to the increase of the cooking zone consumption of power. It means that the cooking zone with the medium heat setting uses less than a half of its power.
The data in the table is for guidance only.
- 1 Keep cooked food warm. as neces- sary
Put a lid on the cookware.
Turn halfway through.
9 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. Power function is activated.
as neces- sary

stains, shiny metallic discoloration. Clean the hob with a moist cloth and non- abrasive detergent. After cleaning, wipe the hob dry with a soft cloth. • Remove shiny metallic discoloration: use a solution of water with vinegar and clean the glass surface with a moist cloth.
What to do if...
Problem Possible cause Remedy
You cannot activate or oper- ate the hob.
The hob is not connected to an electrical supply or it is connected incorrectly.
Check if the hob is correctly connected to the electrical supply. Refer to the connec- tion diagram.
The fuse is blown. Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a qualified electrician.
Activate the hob again and set the heat setting in less than 10 seconds.
You touched 2 or more sen- sor fields at the same time.
Touch only one sensor field.
There is water or fat stains on the control panel.
Clean the control panel.
An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated.
You put something on one or more sensor fields.
Remove the object from the sensor fields.
The hob deactivates. You put something on the
Remove the object from the sensor field.
sensor field .

Problem Possible cause Remedy
Residual heat indicator does not come on.
The zone is not hot because it operated only for a short time.
If the zone operated suffi- ciently long to be hot, speak to an Authorised Service Centre.
Automatic Heat Up function does not operate.
The zone is hot. Let the zone become suffi- ciently cool.
The highest heat setting is set.
The highest heat setting has the same power as the func- tion.
The heat setting changes be- tween two levels.
Power management function operates.
Refer to "Daily use" chapter.
The sensor fields become hot.
The cookware is too large or you put it too near to the controls.
Put large cookware on the rear zones if possible.
comes on. Automatic Switch Off oper- ates.
Deactivate the hob and acti- vate it again.
comes on. The Child Safety Device or the Lock function operates.
Refer to "Daily use" chapter.
comes on. There is no cookware on the zone.
Put cookware on the zone.
The cookware is incorrect. Use the correct cookware. Refer to “Hints and tips” chapter.
The diameter of the bottom of the cookware is too small for the zone.
Use cookware with correct dimensions. Refer to “Technical informa- tion” chapter.
and a number come on. There is an error in the hob. Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again.
If comes on again, speak to an Authorised Service Centre.

Problem Possible cause Remedy
comes on. There is an error in the hob because a cookware boiled dry. Automatic Switch Off and the overheating protec- tion for the zones operate.
Deactivate the hob. Remove the hot cookware. After ap- proximately 30 seconds, acti- vate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware become sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter.
If you cannot find a solution...
message that comes on. Make sure, you operated the hob correctly. If not the servicing by a service technician or dealer will not be free of charge, also during the warranty period. The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet.
If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Give also three digit letter code for the glass ceramic (it is in the corner of the glass surface) and an error
and work surfaces that align to the standards.
Before the installation
Before you install the hob, write down the information bellow from the rating plate. The rating plate is on the bottom of the hob.
Serial number
Only use the built-in hobs after you assemble the hob into correct built-in units





Protection box If you use a protection box (an additional accessory), the front airflow space of 2 mm and the protective floor directly below the hob are not necessary. The protection box accessory may not be available in some countries. Please contact your local supplier.

You can not use the protection box if you install the hob above an oven.
Model PAI8100F PNC 949 594 365 01 Typ 60 GBD C0 AU 220 - 240 V 50 - 60 Hz Induction 7.4 kW Made in Germany Ser.Nr 7.4 kW PROGRESS

Cooking zone Nominal pow- er (maximum heat setting) [W]
Power func- tion maximum duration [min]
Left front 2300 3700 10 180 - 210
Left rear 1800 - - 145 - 180
Middle front 1400 - - 125 - 145
Right rear 2400 3700 10 210 - 300
The power of the cooking zones can be different in some small range from the data in the table. It changes with the material and dimensions of the cookware.
For optimal cooking results use cookware not larger than the diameter in the table.
Type of hob Built-In Hob
Number of cooking zones 4
Diameter of circular cooking zones (Ø)
Left front Left rear Middle front Right rear
21.0 cm 18.0 cm 14.5 cm 30.0 cm
Energy consumption per cooking zone (EC electric cooking)
Left front Left rear Middle front Right rear
181.2 Wh / kg 178.7 Wh / kg 183.9 Wh / kg 171.6 Wh / kg
Energy consumption of the hob (EC electric hob)
178.9 Wh / kg
EN 60350-2 - Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance
You can save energy during everyday cooking if you follow below hints.

dispose appliances marked with the symbol
Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not
with the household waste. Return the product to your local recycling facility or contact your municipal office.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| You cannot activate or oper- ate the hob. | The hob is not connected to an electrical supply or it is connected incorrectly. | Check if the hob is correctly connected to the electrical supply. Refer to the connec- tion diagram. | p.11 |
| You cannot activate or oper- ate the hob. | The fuse is blown. | Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a qualified electrician. | p.11 |
| You cannot activate or oper- ate the hob. | Activate the hob again and set the heat setting in less than 10 seconds. | p.11 | |
| You cannot activate or oper- ate the hob. | You touched 2 or more sen- sor fields at the same time. | Touch only one sensor field. | p.11 |
| You cannot activate or oper- ate the hob. | There is water or fat stains on the control panel. | Clean the control panel. | p.11 |
| An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated. | You put something on one or more sensor fields. | Remove the object from the sensor fields. | p.11 |
| The hob deactivates. | You put something on the sensor field . | Remove the object from the sensor field. | p.11 |
| Residual heat indicator does not come on. | The zone is not hot because it operated only for a short time. | If the zone operated suffi- ciently long to be hot, speak to an Authorised Service Centre. | p.12 |
| Automatic Heat Up function does not operate. | The zone is hot. | Let the zone become suffi- ciently cool. | p.12 |
| Automatic Heat Up function does not operate. | The highest heat setting is set. | The highest heat setting has the same power as the func- tion. | p.12 |
| The heat setting changes be- tween two levels. | Power management function operates. | Refer to "Daily use" chapter. | p.12 |
| The sensor fields become hot. | The cookware is too large or you put it too near to the controls. | Put large cookware on the rear zones if possible. | p.12 |
| comes on. | Automatic Switch Off oper- ates. | Deactivate the hob and acti- vate it again. | p.12 |
| comes on. | The Child Safety Device or the Lock function operates. | Refer to "Daily use" chapter. | p.12 |
| comes on. | There is no cookware on the zone. | Put cookware on the zone. | p.12 |
| comes on. | The cookware is incorrect. | Use the correct cookware. Refer to “Hints and tips” chapter. | p.12 |
| comes on. | The diameter of the bottom of the cookware is too small for the zone. | Use cookware with correct dimensions. Refer to “Technical informa- tion” chapter. | p.12 |
| and a number come on. | There is an error in the hob. | Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again. If comes on again, speak to an Authorised Service Centre. | p.12 |
| comes on. | There is an error in the hob because a cookware boiled dry. Automatic Switch Off and the overheating protec- tion for the zones operate. | Deactivate the hob. Remove the hot cookware. After ap- proximately 30 seconds, acti- vate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware become sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter. | p.13 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.