


V E I L I G H E I D S V O O R S C H R I F T E N
Read this manual first and follow all instructions before you plan to use your scooter for the first time. The following symbols will be used in this manual to indicate warning and danger.
MANDATORY! These actions should be done as specified. Failure to perform mandatory actions may damage the equipment (white symbol on blue point with white edge).
FORBIDDEN! These acts are prohibited; never do and under no circumstances. Doing a prohibited act can damage personal injury and/or property (black symbol with red round and red stripe).
Please fill in the following information for quick reference:
Pride Supplier:
Address:
Telephone number:
Buy Date: Serial number:
Copyright © 2007 Pride Mobility Products Europe B.V. INFMANU3390/RevA/January 2007
088 609 661

II. SAFETY 5
III. SPECIFICATIONS 16
IV. YOUR SCOOTER 18
V. BATTERIES AND CHARGING 24
VI. USE 29
VII. ADJUSTMENT CAPACITY 31
VIII. SOLVING PROBLEMS 34
IX. CARE AND MAINTENANCE 35
X. GUARANTEE 38

SAFETY WELCOME to Pride Mobility Products Europe B. V. (Pride). The product you bought combines state of the art parts with safety, comfort and styling. We are sure that the design features will provide you with the conveniences you expect in daily life. Understand how to use this product Safe must serve and care will provide you with service for years without any problems.
Read and follow all the instructions, warnings and notes in this manual and any other enclosed literature before you try to operate this product for the first time. In addition, your safety to you, and your supplier, aid worker or medical counselor in the use of your best insight.
If there is any information in this manual that you do not understand, or if you need further help in assembly or operation, please contact your competent Pride Supplier. Negligibility to follow the regulations, warnings, and notes in this manual and these on your Pride product may cause personal injury or damage to the product and render the Pride Product Guarantee void.
SUPPLIER AGREEMENT By receiving this product, you promise that you will not change, modify or modify this product or remove any protections, securitys or other safety features of this product; fail, refuse or fail to install from time to time any renewal kits provided by Pride in order to improve or preserve the safe use of this Product.
INFORMATION EXCHANGE We would like to hear your questions, comments and suggestions about this manual. We would also like to hear about the safety and reliability of your new scooter and the service you receive from your competent Pride Supplier. Please give us your address change so we can keep you informed about safety, new products, and new options that may improve your ability to use and enjoy your scooter. Please contact us at the address below:
Pride Mobility Products Europe B. V.
Tijnmuiden 28 1046 AL Amsterdam The Netherlands

I I . V E I L I G H E I D
PRODUCT SAFETY SYMBOLS The symbols below are used on the scooter to indicate warnings, mandatory acts, and prohibited actions. It is very important that you read and understand it completely.
Pinch/squeeze points created during assembly.
Batteries contain corrosive chemicals. Use only AGM or Gel-Cell batteries to reduce the risk of leaks or explosions.
Read and follow the information in the user manual.

Maximum weight capacity.
Unlocked and freewheel mode.
Place unit on ground floor and stand behind or on one side when changing drive mode to freewheel mode or freewheel fashion to drive mode.
Locked and in drive mode.
Front back plug orientation.

I I . V E I L I G H E I D
Use only AGM or gel batteries.
Do not remove the anti-tip wheels.
Do not use cell phone, walkie-talkie, laptop or other radio transistor during use.
Avoid exposure to rain, snow, ice, salt or still water whenever possible. Maintains and stores in a clean and dry condition.
The removal of the ground can create an electrical hazard. If necessary, mount a allowed grounded adapter to an outlet without earth. Failure can cause personal injury and/or tool damage.
Prevents personal injury and tool damage. Do not connect an extension cord to the AC/DC converter or battery charger.
Contact with tools can cause an electric shock.
Keep your hands away from the tires while driving. Make sure that loose clothing can get stuck in the drive wheels.
Disposal and recycling: contact Pride's authorized supplier for information on disposal and recycling of your Pride product and packaging.

I I . V E I L I G H E I D
MANDATORY! Before you start using your scooter for the first time, you must read and understand this manual completely.
Your scooter is designed to facilitate your life and increase mobility. Pride supplies a large number of products that best meet the needs of scooter users. Please note that the final decision to choose and purchase the type of scooter to be used is ultimately the responsibility of the scooters user and his/her medical supervisor (such as doctor, physiotherapist etc.).
The contents of this manual are based on the expectation that an expert in rehabilitation aids has adjusted the scooter to the needs of the user and given careful instructions.
There are certain situations, including some medical conditions, in which the user will have to practice before an expert. This can be a family member or an auxiliary who is specially trained in the supervision of a scooter user during various daily activities.
At the beginning you may encounter situations where you need some exercise. Take your time and you will soon become fully familiar with your scooter.
Below are some precautions, tips and other safety considerations intended to familiarise you with the use of your new scooter.
AMENDMENTS Pride has designed your scooter to provide you with scooters and mobility. There are a large number of accessories available to adapt your scooter even more to your personal needs and wishes. However, under no circumstances may you make changes to your scooter, such as adding or deleting parts, rendering functions disabled etc.
PRE-SAFETY TEST Get to know yourself with the scooter and its capabilities. Pride recommends that you carry out a safety check before each use to ensure your scooter functions smoothly and safely. For details of this inspection see Chapter IX. . .
Before using your scooter, perform the following inspections: . . Check all electrical connections. Make sure they're well-stuck and not rusted. . Check the brakes. . Check the battery charge.
NOTE: If you have a problem, please contact your supplier.

I I . V E I L I G H E I D
SCOOTER; WEIGHT OF LOAD Your scooter is calculated on a maximum weight of 136 kg. Please refer to the specification table for this limit.
GETTING OFF YOUR SCOOTER This requires a good sense of balance. Therefore, please carefully review the following safety tips. . Make sure your scooter is not in free range. See IV. . . Your Scooter. ♪ . Make sure the seat is securely locked and that the key has been removed from the switch.
BELTS It is the responsibility of your competent Pride supplier, therapists and other medical supervisors to determine which fixation belts you need to ride your scooter safely.
RAMPS AND SLOPES More and more buildings have ramps with a certain rate of increase, designed for safe and easy entrance. Some driveways have a bend, so you need some experience with your scooter. • Drive extremely carefully when you are going down a driveway or slope. . . At a sharp angle, take slow wide curves with your front wheel. If you do, the
Follow rear wheels and do not hit the sharp corner or stay behind a rail. . . When you drive down from a driveway, turn your speed button to the lowest position in order to make such an
ensure safe, controlled descent. See IV. . Your Scooter. . ♪ Avoid sudden stops and starts.

I I . V E I L I G H E I D
Try to keep your scooter moving while climbing a slope. If you need to stop already, start slowly again and gently gas. When descending, you need to set the speed button at the lowest position and drive forward only. If your scooter can descend faster than you wish or the slope can degrade, then stop it completely by releasing the throttle. Then gently push the throttle forward to descend safely and controlled.
Some slopes are naturally or specially constructed, not directly suitable for scooters. Figure 1 show the stability of your scooter and show which slope you can ride with various weight weights and under controlled test conditions.
These tests are performed with the scooter seat in the highest position and set as far back as possible. Use this information as a guide. The incline capacity of your scooter is affected by your weight, the speed of the scooters, the angle at which you approach the slope and the settings of your Scooter.
Figure 1. The maximum recommended inclination angle
136 kg 8,7%/(5º)

I I . V E I L I G H E I D
When approaching a slope, it is best to lean forward. See Figures 2 and 2A. Then the center of gravity of you and your scooter slides to the front of the scooters for better stability.
Figure 2A. Increased Stability Driving Position Figure 2. Normal Row Position
BRAKES Your Scooter is equipped with two strong braking systems: .Rendering: uses electric energy to quickly slow down when the gas lever in neutral-
/stop mode is set and. . . Motor brake automatically blocks after the Scooter has almost stopped, or when
For whatever reason, the energy is falling out.
TAKING TURNS Extremely high speed in curves can lead to tilting of your scooter. Factors that increase the risk of tilting include: (but not only): the speed in curves, the steering angle (i.e. how sharp you are) uneven terrain, sloping terrain, driving a low-tensile terrain to a lot of traction (such as coming from a grassy terrain on a paved terrain - especially when turning at high speed) and abrupt change in direction. High speed at turns is strongly advised. If you feel like your scooter can tilt, reduce speed and adjust the steering angle (i.e. make the turn less sharp).

I I . V E I L I G H E I D
ROAD SURFACE Your scooter is designed to provide you with optimum stability under normal driving conditions, such as hardened road surface, concrete or asphalt. Pride understands, however, that there will be times when you can also face other types of road. For this reason, your scooter is also designed to be used well on other solid surfaces, grass or gravel. . > >. < <. >> Less your speed when you are on uneven terrain and/or soft ground. . . Avoid high grass that can run in the engine. . . Avoid loose gravel and sand. . If you have doubts about a site, avoid it.
FIXED OBSTACLES (STEPS, PAVEMENTS, ETC.) Always approach a pavement belt perpendicular to climbing or descending. See fguren 3 and 3A.
STRAP
Figure 3. Correct approach Figure 3A. Bad approach

I I . V E I L I G H E I D
ESCALATORS AND ESCALATORS Scooters are not designed to go up or down stairs and escalators. Always use the elevator.
DOORS. . Determine whether a door is turning towards you or off. . Use your hand to turn the door knob or pull the door towards you or push it away. . Drive forward slowly to push the door open. Or slow back to open the door
Pull.
LIFTS The modern lifts have a safety mechanism in the door edge which makes doors open again when touched. . . When you are standing in the doorway of an elevator while doors close, push against the rubber
Door edge or make sure your scooter hits this edge and the doors will open again. . Make sure that groceries, bags or scooter accessories do not stick between the lift doors.
FREE RANGE MODE Your scooter is equipped with a manual freewalk lever that, when disconnected, allows your scooters to move forward manually. For more information on unplugging the free-loop lever, see IV. .Your Scooter.
WARNING! If you set your scooter in the freewheel mode, the brakes are not switched on. Follow these safety instructions when you set your scooter to freeload mode: . . Do not put your scooter in the free run position when you are on a slope with your scioter; your scoider can drive down by itself. . . Before you set your scooter to free-run mode, you are aware that the key has been removed from the key switch. . . If you want to set the scooter in freestyle mode, then acher the scooter when doing so. Do not sit on your scooter when it is in the freestyle position. . . When you are ready to move your scooter manually, always switch it back off the freewheel mode so that you can turn on the brakes again.
Ignoring these safety regulations can lead to personal injury and/or damage to your scooter.

I I . V E I L I G H E I D
ELECTROMAGNETIC FIELDS Your scooter's driving behaviour can be influenced by electromagnetic fields caused by electronic devices such as mobile phones, transmitters, portable radio transmission masts, radio and television stations etc.
TRANSPORT IN A MOVING VEHICLE At present, there are no approved standards for fixation systems in any type of moving vehicle to transport a person while he is in a scooter.
Despite the fact that your scooter may be equipped with a belt, this belt is not designed to protect you during transport in a vehicle. In a moving vehicle, everyone must use well-attached seat belts.
LIFTING AIDS While travelling with your scooter you may need a lift as a transport assistance. Pride then advises to strictly follow the instructions and safety requirements of this particular device before using it.

I I . V E I L I G H E I D
BATTERIES In addition to the warnings listed below, you should also read all other information about handling batteries properly. For more information see V. .Batteries and loading.
RECYCLING AND DISPENSING OF BATTERIES If you find a damaged battery, make sure to immediately enclose it in a platic bag and contact your competent Pride supplier for disclosure instructions. Your competent Pride supplier also has the necessary information about recycling batteries, which is our preference.
REACH AND DUCK Avoid any reck and bend movements when your scooter is in motion. If you need to make any of these movements it is important that you maintain a stable point of gravity so the scooter cannot reverse. Pride orders that the scooter user determines what his or her personal limitations are and exert reaching and ducking in the presence of a qualified health care professional.
WARNING! Do not stretch or duck between your legs for an object if you pick it up from the floor. Such movements can change the point of gravity and the weight of distribution of the scooter, causing the scout to tip around and result in possible personal injury. Do not keep your hands near the tires as you move your scooter.

I I . V E I L I G H E I D
USE OF MEDICINES/PHYSICAL RESTRICTIONS A scooter user should handle his scooters carefully and wisely. Especially when using medicines or in the event of physical impairment, safety requirements should be well aware.
ALCOHOL A scooter user should be careful and wise to deal with his scooters. Also when using alcohol, we must be aware of safety requirements.
Electromagnetic and radio frequency influence can be caused by sources such as mobile phones, two-way mobile radio jammers (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computers, microwave, pacemakers and medium distance mobile receivers used by rescue vehicles. In some cases, such waves can cause unintentional movements or damage the control system. Each electrically driven vehicle has a certain immunity (or resistance) for EMI. The higher the level of immunity, the greater the protection against EMI. This product has been tested and meets an immunity level of V/M.
WARNING! Be suspicious that mobile phones, two-way radios, laptops and other types of radio transmitters may cause unintentional movements of your electrically driven vehicle as a result of EMI. Be careful if you use any of these while driving in your electric vehicle and make sure that you do not get too close to radio and TV stations.
NOTE: For more information about EMI/RFI, visit the Resource Center website www.pridemobility.com If unintentional movements or brakes occur, switch the Scooter as If possible, quickly out if safe. Contact a recognized supplier to contact Report incident.

I I I . S P E C I F I C A T I E S

Figure 4A. Tyres

I I I . S P E C I F I C A T I E S
SPECIFICATIONS Model number SC2601ENCRED15 Available Colors Red Class of Use C Maximum Safe Slope See Figure 1. Maximum Climb Capacity See Figure 1. Length2 140 cm Width2 65 cm Weight without battery life 78 kg Heavyest component Rear frame: 54,5 kg at dismantling Rotation circle2 120 cm Speed (max.) 1 Up to 15 km/h Distance per charge1 (With 55 AH batteries) Up to 40 km Ground clearance2 13 cm Maximum load: 136 kg Seat Type: DX contour medium black Dimensions: 52 cm width x 50 cm depth x 51 cm height (usable) Black: Vinyl; Brown Drive Rear wheel drive, closed transaxle, 24 Volt DC motor Brake system Electromagnetic brakes Tyres 10 x 33 cm Batteries Type: Two 12 volts deep cycle(AGM or Gel-Cell) Size: 55 AH Battery Weight About: (55 AH) 9 kg Each Loader External charger
1 Ranks due to the weight of the user, type of subsurface, battery strength (AH), battery capacity, battery condition, and condition of tires. 2 Due to manufacturing differences and constant improvements to the product, these specifications may vary to (+ or -) 3%.
NOTE: All specifications may be changed without prior notice.

Your Scooter is an indoor/outdoor electric powered scooter, which has been developed to increase your mobility. For easy transport or storage, you can disassemble your Scooter in 6 parts. See Figure 5.

DASHBOARD The dashboard, on the top of the steering wheel, contains all the features you need to ride your scooter. See Figure 6.
Figure 5. Scooter Parts
Battery condition indicator If the key is fully inserted into the ignition lock turn it to the right to make contact, then the battery meter indicates how full the batteries are about. For more information on charging of batteries see Chapter V. .Batteries and loading.

Speed control lever If you pull the right speed control lever towards you, move the scooter forward. If you push the right speed control lever off of you, move the scooter backwards.
If you pull the left speed control lever towards you, move the scooter backwards. If you push the left speed control lever off of you, move the scooter forward.
On/off switch LED When the LED is on, this means that the scooter is .

Claxon These buttons activate the horn. Make sure the key is in the switch and press the horn.
Key switch This switch gives you the possibility to turn on and/or off your scooter. . . Put the key completely into the switch and turn it right to turn on the scooter. . Turn the key to the left and remove it from the switch to turn off your scooter completely.
Gas lever These levers give you control over the speed forward and reverse of the Scooter or, depending on the position of the scooter button for setting.
Driving forward with your scooter can be done in 2 ways:. Use your left thumb to press the left side of the gas lever. . Use your right hand fingers to squeeze the gas lever on the right side.
The reverse drive with your scooter can be in 2 ways:. Use your right thumb to press the right hand side of the gas lever. . Use your left hand fingers to squeeze the gas lever on the left side.
Release the throttle and let your Scooter come to a complete standstill before pushing the gas lever in the other direction. When the throttle is completely released, it returns to the .zero position .and activates your Scooter brake.
This switch gives you the possibility to turn on and off the front lamp and rear lights. Pride advises you to turn on the light if it becomes too dusk for safe use.
Alarm light switch This switch gives you the possibility to blink direction indicators in front and rear (orange) at once.
Light switch

Direction indicators Use these switches to activate the left and right direction indicators (orange). With each switch you can control both flashing lights. See Figure 7. 1. BY Press the switch forward, the direction indicator shall be operated on that side. 2. Pull the switch backwards, and it activates the direction indicator for the opposite side. 3. To switch off the flashing light, press the switch of the illuminated direction indicator lamp slightly forward.
Hand brake Your scooter is equipped with a hand brake, placed on the wheel. This lever gives you an extra brake possibility. Release the speed control lever and slowly squeeze the hand brake to stop. See Figure 8.
TYPICAL: If you do not release the speed control lever before using the hand brake, your scooter could not come to complete standstill.
RIGHT DIRECTION INDICATOR SWITCH HAND BRAKE LEVER
Figure 7. Dashboard Figure 8. Hand Brake Hendel
FUSE BOX The fuse box is placed at the rear of the steering column, below the entrance to the charging plug. It contains five automatic fuses, which protect the dashboard information and light system from too high an electric power supply. The fuse box contains a 5 amp. fuse and four 3 amp. Fuses. See Figure 9. . . The battery voltage is secured for the
3-AMP
SPARE
Dashboard with the 5 amp. fuse. . The direction indicators and the light shall be
Secured for the dashboard with three out of 3 amp. Fuses. . The fourth 3 amp. fuse is a reserve fuse.
Figure 9. fuse box

HIND COVER The hind cover is a removable plastic cap, which protects the rear part with all components. To remove the hind cover, you will first have to take the scooter seat. (See VII. . Turn every quick release one quarter to the left. See Figure 10. 2. Gently lift the hind cover up. 3. Unplug the rear-light plugs completely to remove the hind cover.

Figure 10. Fast release
REAR PART The batteries, the controller, the automatic fuse, the engine, the hind cover, the manual freewheel lever, the anti-kip wheels, and some fuses are in the rear part of your scooter. See Figure 10A.

Figure 10A. Rear part

Anti-kip Wheels The anti-gip wheels are designed for your safety and designed to prevent your scooter falling backwards on a slope. They are welded to the frame on the rear part of your scooter.
FORBIDDEN! Do not remove the anti-gip wheels or change your scooter in any way without Pride's permission.
Batteries The batteries contain the electrical energy your scooter needs. For instructions on how to load your batteries, see V, .Batteries and charging.
Electronic controller module This module is located behind the batteries on the left corner front of the rear part. The electronic controller module receives electronic signals from the dashboard and controls the engine, brakes and lighting system.
Engine/Drive structure It is a single, directly driven fully sealed structure. Designed for low-noise operation with maximum power and life.
Manually operated free-loop lever If you want to move your scooter a bit, you can put it in a freewalk position. . . The manual free-loop lever is at the end of the engine/drive to the right
back of the scooter. . Pull the freewheel lever upwards to uncouple the braking system. You can then scooter
Push. . . Press the freewheel lever down to activate and remove the braking system from the release.
WARNING! It is important to remember that if your scooter is in freewheel mode, the braking system is not running. Follow the following safety instructions when using the free-walk lever. . . Do not set the engine in a freewheel position if you are on a slope. The scooter can roll down and cause injury. . . Before you put your scooter in or out of the free-run position, convince yourself that the key has been removed from the lock. . Never sit on a scooter when it is in the free range position. . . Once you've finished pushing your scooter, press the lever directly down in the driving position to re-enable the brakes.

Automatic fuse If the voltage in your batteries is low or your scooter occasionally drives inhibited, due to too low voltage, automatic fuse can enter into operation to protect the engine and electronics from damage. If this automatic fuse is activated, the entire electronics system will be switched off. See Figure 11. . . The reset button is used to stop the interruption. . The reset knob of the automatic fuse is in the rear hood underneath the seat. . . The reset button will jump out when the automatic fuse is activated. . . Give the electronics a minute or so rest. . . Press the reset button to lift the interruption. . . If the automatic circuit breaker is running regularly, you may need to increase battery frequency
Load or have your competent Pride supplier run a voltage test on your batteries.
Figure 11. Automatic Fiber (Reset Button)

V. B A T T E R I J E N E N H E T L A D E N
Your scooter needs two 12-volt, dry gel batteries that are closed and maintenance-free. Three important points to remember are: . . Load your batteries with the included battery charger before you start using it for the first time. . . Keeps your batteries charged as much as possible, to allow your scooter to drive. . Use only the battery charger provided with your scooter.
READING YOUR BATTERY VOLTAGE The battery conditioner on the control panel gives an indication in color codes of how much energy your batteries contain. See Figure 12. Green; batteries fully charged, yellow; decreasing charge, and red; charging should be done immediately. To check your load, you first need to remove the charging cord from the socket and turn on your scooter.


Figure 12. Battery condition indicator
FORBIDDEN! Never use an extension cord to connect your battery charger. Connect the battery charger directly to a standard stop contact in the wall.
FORBIDDEN! Removing the earth tooth from your plug can cause electrical danger. If necessary, install a proven 3 tooth adapter at the stop contact which has a 2 tooth connection.

V. B A T T E R I J E N E N H E T L A D E N
WARNING! If your battery charger has not been tested and approved for outdoor use, you should not expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse or extreme weather conditions, you should allow it to adapt to new environmental conditions before using it again indoors. Please observe the battery charger instructions for further information.
Follow the following steps to safely load your batteries: 1. Put your scooter close to an outlet. 2. Remove the key from the switch. 3. Convince yourself that the freewheel lever is in the row position (downwards). 4. Connect the battery charger to the charging contact, it is located at the bottom of the dashboard on your scooter and the wall socket. 5. Follow the instructions given by the manufacturer of the charger. 6. If the batteries are fully charged, first pull the plug from the wall socket and then out of the charging contact on your scooter. 7. Place the charger in a safe place for future use.
Figure 13. Load contact
. .: There is a loading blocking function on your scooter. Your scooter will not drive and the Battery conditioner will not work while the batteries are charged.
FAQ How does the charger work? When your scooter battery voltage is low, the charger works harder, and transmit more electric power to the batteries to bring them up to level. When the voltage reaches a full charge, the charger will send less and less electric current to the batteries. When the batteries are fully charged, the current sent by the charger is almost zero ampere. Therefore, once the charger is connected there will remain power on the batteries but they will not be overloaded. We do not recommend charging your scooter's batteries for more than 24 hours.
What to do if the batteries are not charged?. . Ensure that both ends of the charger are correctly connected.
How many times do I have to charge the batteries? Two major factors should be considered when deciding how often to charge the batteries: . . Daily use of your scooter. • Sporadic use of your scooter.

V. B A T T E R I J E N E N H E T L A D E N
With these 2 factors in mind, you can determine how often and for how long to charge your batteries. We have developed the external charger so that it cannot overload your batteries. However, you may encounter some problems if you do not charge your batteries often enough and if you don't charge the batteries regularly. Here are 5 rules that will provide you with a safe and reliable battery charge. . . If you use your scooter daily, charge the batteries if you stop using the scooters
the end of the day. Your scooter will be fully charged for your daily use every morning. We recommend that you charge your batteries for 8 . • If you use your scooter once a week or less, charge the batteries for 12 • 14 hours
at least once a week. . Keeps your batteries fully charged. . . Avoid deep discharge of your batteries. . . Charges your batteries no longer than 24 hours in one piece.
How can I reach the maximum distance per load? You will rarely have ideal driving conditions, smooth, tight or hard driving surfaces, no headwinds or turns. Often you will encounter slopes, pavements, bends, wind, uneven and loose ground. All these driving conditions affect the distance or driving time per battery charge. Now follow some suggestions to reach the maximum distance per battery charge. . . Always load the batteries the day before use. . . If your scooter has pneumatic tires, hold 2-2.4 bar In every band. . Plan your route to avoid as many slopes, bumpy or soft surfaces as possible. . Limit your luggage weight to the necessary things. . Try to keep as much speed as possible when you drive your scooter. . . Avoid many start-up and stop situations, drive regularly.
What type and size of batteries should I use? We recommend using deep cycle batteries that are closed and without maintenance. Both AGM and Gel-Cell are deep cycle batteries that are even in performance. Do not use wet cell batteries, which have removable caps.
CHARGE: Closed batteries are not durable. Do not remove the caps.

V. B A T T E R I J E N E N H E T L A D E N
To replace a battery in your scooter: 1. Remove the seat by lifting it out of the chair bar. 2. Carefully remove the hind cover of your scooter by lifting it. 3. Untie the belt that holds the battery. 4. Unplug the connector of the controller module. 5. Unplug the battery compartment electric connector. 6. Remove the old battery. 7. Place a new battery in the battery compartment. 8. Connect the red battery cable to the plus (+) of the battery compartment. 9. Connect the black battery cable to the min (-) of the battery compartment. 10. Reconnect the batteries to the controller module. 11. Re-lock the batteries with the belt. 12. Install the back cover of your scooter and seat.
Why does it seem like my new batteries are weak? Deep-cycle batteries use a different chemical technology than the batteries of a car or other normally occurring batteries. Deep-cycle batteries are specifically designed to provide power, discharge and then recharge relatively quickly.
We work close with our battery manufacturer to provide batteries that best meet the specific needs of your scooter. Fresh batteries arrive at Pride and are fully charged to our customers. During the transmission, batteries may encounter extreme temperatures that can influence their initial performance. Heat reduces the charge power of a battery, cold slows down the charging force available and stretches out the time needed to recharge the battery. It may take a few days for the temperature of your scooter batteries to stabilize and adapt to their new room or environment temperature. More importantly, it takes a few charging cycles (partially unloaded followed by full recharge) to determine the critical chemical balance required to establish a deep cycle battery peak performance and long life.
Follow the next steps to ensure that you get your new batteries off to a good start. 1. Charge your batteries completely before using them the first time. This charge brings the batteries up to 88% of the top performance. 2. Use your scooter in safe and trusted areas so you get used to the action of your new scooters and don't overcharge batteries the first time. Do not take .hounds of . and do not drive too long distances. 3. Charges your batteries completely. This charge brings the batteries over 90% of its top performance. 4. Use your scooter. 5. Recharge your batteries completely. 6. After four or five loads, this brings the batteries up to 100% of the top performance and will last for a longer time per charge.

V. B A T T E R I J E N E N H E T L A D E N
How can I ensure maximum battery life? Fully charged, well treated batteries ensure reliable capacity and last longer. Keep the batteries fully filled. Batteries that are deeply discharged, loaded irregularly or stored without a full charge can be permanently damaged. They're unreliable in use.
BATTERY DESTRUCTION AND RECYCLING If you encounter a damaged or cracked battery, place it immediately in a plastic bag and contact your competent Pride Supplier for instructions on destruction. Your competent Pride Supplier will also have the necessary information about recycling old or damaged batteries, which is our recommended way of action.

BEFORE YOU STEP ON YOUR SCOOTER. Did you fully charge your batteries? See V. . .Batteries and loading. ♪ . is the manual free-loop lever in driving position (backwards)? Leave the manual freewalk lever
Never stand in the free range position (forward) unless you are moving the Scooter manually. . Is the steering column unlocked?
1. Make sure the key is removed from the switch. 2. Stand next to your Scooter. 3. Unlock the seat lock handle and twist the chair until it is turned towards you. 4. Release the lever and securely lock the seat in position 5. Sit comfortably and firmly in the chair. 6. Unlock the chair lock handle and twist the seat until you look forward. 7. Release the lever and securely lock the seat in position. 8. Put your feet safely on the bottom of the Scooter.
PRECAUTIONARY AND CONTROL. . is the seat adjusted to its correct height? See VII. . .Setting capacity. • . Is the seat securely fixed? . is the adjustable steering column set to a comfortable position and securely fixed? See VII. . .Settingability. ♪ . Is the key inserted completely into the switch? ♪ Does the horn work well? . . Is your proposed route free from people, animals and obstacles? . Did you plan your route to miss out on adversaries and open as many slopes as possible?
Such practices can cause loss of control and/or rotation, causing personal injury and/ or damage to your Scooter.
Keep both hands on the wheel and your feet at all times on the floorboard while you move the Scooter. This row position gives you the most control over the vehicle. . . Set the speed switch to your desired position. . Push or pull on the relevant side of the gas control lever. . . The electromagnetic brake is automatically disconnected and the Scooter accelerates smoothly to the
speed you set in advance.

. Pull the left handle to turn left. . Pull the right handle to turn right. . Move the steering wheel to the centre position to continue straight ahead. . . Release the gas lever slowly to fully stop. The electromechanical brake will be
automatically enter into operation if your Scooter comes to a standstill.
CHARGE: Your Scooter's reverse speed is longer than that of the forward speed which you turn from the front with the speed selector.
GETTING OFF YOUR SCOOTER 1. Completely stop your Scooter. 2. Remove the key from the switch. 3. Unlock the seat lock switch and turn the seat until you look at the side of your Scooter. 4. Make sure the seat is securely locked. 5. Careful and safe come from the seat and stand on your Scooter side. 6. You can leave the seat to the side of it to make it easier next time you come on your Scooter.
ENERGY CONSUMPTION DECREASE TIMER COMPONENT Your Scooter has an energy saving automatic reducing component designed to save your Scooters battery life. If you accidentally leave the key in the keyhole in the .aan .b position but your Scooter does not use it for about 20 minutes, the scooters controller automatically turns off. Although the controller is closed off, and the Scooter cannot move, the power will still be delivered to the Scutters lighting system.
If an energy consumption decreasing component starts to operate, take the next steps to resume normal function again. 1. Remove the key from the keyhole. 2. Re-insert the key and increase your Scooter's energy consumption.


V I I . I N S T E L B A A R H E I D
ADJUSTABLE STEERING COLUMN Your steering wheel is equipped with a lever to adjust your steering column, which allows you to fasten your steering wheel as well as turn it and change it in the correct position.
To adjust your steering wheel: 1. Turn the steering adjustment lever to the left until it is loose. If this lever comes into contact with the steering basket pull the handle outwards, turn it to the right so that it is released. Turn it off just as far as you can until the wheel is moved. 2. Set the steering wheel in position. 3. Turn the steering adjustment lever clockwise until it is re-locked.
TYPICAL: The handlebar can be lowered to the centre of the base plate and it can be Stuck for storage.
To lower the steering wheel to the base plate: 1. Turn the steering lever counterclockwise until it is loose. 2. Pull the steering rubber up to release the uncoupled buttons from the wheel. 3. Take the handlebar handle and gently press both steering uncouple buttons, while slowly pushing down the steering column. See Figure 15. 4. If the steering column has reached its lowest point, turn on the steering adjustment lever in the direction of the clock until it is fixed to position.

Figure 14. Steering angle adjustment Figure 15. Lower the steering wheel

V I I . I N S T E L B A A R H E I D
SEAT HEIGHT SETTING To place the seat on one of three heights: 1. Remove the seat from your scooter. Press the lever to secure the seat, then turn the chair and lift it off the scooter. 2. Remove the hind cover. 3. Remove the bolt from the seat column. See Figure 16. 4. Lift or lower your seat holder to the desired height. 5. Keep the seat holder at that height and make sure that the hole in the seat column and chair holder are equal. 6. Place the bolt back in the seat column. 7. Put the seat back in place.
WASHER
LAUNDRY
SCREW
BOUT
SEAT COLUMN
Figure 16. Seat height adjustment OF THE STOLE The seat attachment lever secures the chair in one of the 7 positions. Round the seat turn: 1. Pull the seat attachment lever to unplug the chair. 2. Turn the seat to your desired position. 3. Release the seat attachment handle to re-lock the chair. If the seat is not attached to that position, gently move the chair left or right until you hear it clicking into the lever.
BACK ANGLE SETTING To adjust the seat-back: 1. Pull the seat-back lever to unplug the backrest. 2. Lean forward or backwards to adjust the backrest to a comfortable position. 3. Release the lever to re-lock the railing.
ARMREST ANGLE ADJUSTMENT The armrest angle of your scooter can be adjusted up or down by turning the adjustment button.

V I I . I N S T E L B A A R H E I D
SAFETY BELT Your scooter can be equipped with an adjustable safety belt (see Figure 18). The safety belt is designed to ensure that the rider is not able to slide sideways or forwards. The safety belt is NOT developed as a means to secure a person in the seat.
Installing the safety belt: 1. Remove the seat from your scooter 2. Place the seat upside down so you can see the bottom of your chair (See Figure 17). 3. Remove the bolts on the outside of the seat mounting plate at the rear of the chair (See Figure 17). 4. Enter the bolts through the hole in the ends of the safety belt and then place them back into their holes in the seat-mounted mounting plate. 5. Turn the bolts on properly.
Adjusting the safety belt: 1. Put the metal end of one side of the safety belt into the plastic housing on the other side of your seatbelt until you hear a . 2. Pull on the loose end of the safety belt until you are secure, but not so fast that it becomes uncomfortable.
MANDATORY! Avoid personal injuries! Make sure that the safety belt is correctly attached to the electric Scooter and that it is conveniently adjusted for the user.
MANDATORY! Avoid personal injuries and damage! Before each use of the Scooter, check the seat belt for loose and damaged parts. If you find a problem, please contact your authorized Pride Supplier for maintenance and repair.
DELETE BOLT

BACKREST ADJUSTMENT LEVER
SESSION LOCK LEVER
SEAT SLIDING HANDLE
Figure 18. Seat belt Figure 17. Installation of safety belt

V I I I . H E T O P L O S S E N VA N P RO B L E M E N
Every electromechanic device has occasional malfunctions. Many of these problems arise because the batteries are not fully charged or obsolete.
All my scooter systems seem to have gone out. One of the following actions can solve the problem. Remove the key and put it back in the keyhole. Make sure the batteries are fully charged. Press the automatic fuse by means of: reset button in. Make sure that both battery cables are securely attached to the electronic controller unit and at the battery poles. Make sure that the cables running from front to rear are well connected.
My battery conditioner shows a full load, but my scooter does not drive when I impress the speed lever.
Make sure your scooter isn't in the free range. (Press the manual release lever down to normal use.)
TYPICAL: If the manual freewheel to operate lever up, your brakes are out of use and all Power to the drive is off.
Automatic fuse keeps jumping out. One of the following actions can solve the problem. Charge your batteries more often. Have both batteries tested by your competent Pride supplier.
The battery conditioner on my scooter keeps dropping and the engine stuttering or refusing when I push the speed lever.
One of the following actions can solve the problem. Charge your batteries completely. Have your competent Pride supplier test the charge of each battery.
If you have problems with your scooter, which you cannot solve, please contact your competent Pride supplier directly for information, maintenance and service.

I X . V E R Z O R G I N G E N O N D E R H O U D
Your Scooter needs a minimum of care and maintenance. If you do not think that you can meet the maintenance specified below, please consult your competent Pride supplier. The following areas require periodic inspection or care and/or maintenance.
TYRE PRESSURE. . Inspect your tires regularly for irregularities or weaknesses. . . If the Scooter is equipped with pneumatic tires, always keep a correct 2-2.4 bar Tyre pressure.
WARNING! It is important that 2-2.4 bar tires are maintained in pneumatic tyres at all times. Do not blow your tires too hard or too soft. Low pressure can cause loss in control, and tires with too high pressure can blow up. Failure to keep 2-2.4 bar tire pressure at all times can cause tyre and/or wheel failure, seriously causing personal injury and/ or damage to your Scooter.
REPLACEMENT OF THE WHEELS If your Scooter is fitted with pneumatic tyres and you have a flat tyre, you can get it replaced. If your Scooter is fitted with a solid belt, either the massive tyre or the entire wheel should be replaced depending on the model. Contact your recognized Pride Supplier for more information about the replacement of your Scooter wheels.
OUTER SURFACES Bumpers and other surfaces can also be maintained with rubber or vinyl conditioner.
CLEANING AND DISINFECTION. . Use a damp cloth and a mild, non-slashing cleanser to cover the plastic and metal parts
clean your Scooter. Avoid using products that could cause scratches on the surface of your Scooter. • If necessary, you can clean the product with an approved disinfectant. Make sure
use before, that the medicine is safe for use on your Scooter.
BATTERY TERMINAL CONNECTIONS. . Make sure that terminal connections remain secure and are not corroded. . The batteries must be in the battery shafts flat. . The battery poles should point to the back of the Scooter.

I X . V E R Z O R G I N G E N O N D E R H O U D
WIRING HARNESS. . Regularly check all wiring connections. . . Regularly check all wiring insulation, including the battery charger, for wear or damage. . . Let any damaged connection, connection or insulation be repaired or replaced by a competent
Pride service mechanic, before you start using your Scooter.
ABS PLASTIC COVER. . The front for the stick cover, for cover, and the rear manter are formed of durable ABS
plastic and are protected with an advanced formula urethane paint. . . A light application autowash will help the mantles to maintain their high shine.
LOWER AND ENGINE/TRANSAXEL You do not need to oil these parts, because all of them are pre-oiled and sealed.
MOTOR BRUSHES The motor brushes were found in the engine transas/assembly. They must be periodically inspected by your competent Pride Representative.
CONTROL PANEL, CHARGER AND REAR ELECTRONICS. . Keeps these parts free of moisture. . . Let these areas dry ground when they have been exposed to moisture, before you use your Scooter
weer gebruikt.
FUSE REPLACEMENT In case a fuse would stop working: 1. Remove the fuse by pulling it out of the groove 2. Check the fuse to make sure it's blown out. See Figure 19 and 20. 3. Insert a new fuse with the right Amperage.
Figure 19. Working fuse Figure 20. Flashed fuse (replace)

I X . V E R Z O R G I N G E N O N D E R H O U D
BULB REPLACEMENT The scooter's light bulbs are easy to replace. Do not use ordinary automotive sootr 12 volt light bulbs; your Scooter has a 24 volt electric system. Replacement bulbs can be purchased from your authorized Pride Supplier.
TYPE: Use only 24-volt light bulbs.
REPLACEMENT OF A NYLON NUT Any nylon nut removed from the Scooter during periodic maintenance, assembly or dismantling shall be replaced by a new one. Nylon nuts cannot be reused, because there can be damage to the nylon thread, which means that no more good fixing is involved. Replacement nylon nuts are available from a local hardware lever or your authorized Pride Supplier.
STORAGE If you are planning not to use your Scooter for a certain period of time, it is advisable to do the following: . . Load up batteries completely before saving them. . . Remove the battery suits from the Scooter. . Save your Scooter in a warm dry environment. . . Avoid storing your Scooter in areas where it is exposed to large
temperature differences.
For longer storage it is better to place some shelves under the frame of your Scooter to lift them off the ground. This is to get the weight off the tires. This prevents the occurrence of weak spots on your tires.
DISPOSAL OF YOUR SCOOTER You must dispose of your Scooter according to local rules. Contact local waste disposal or your authorized Pride Supplier for information on the correct way to dispose of your Scooter, metal frame, plastic parts, electronics and battery .

Two JARIGE-Limited GUARANTEE Structural skeleton, including:. . Platform .
A LIMITED WARRANTY FOR THE YEAR Your Pride Scooter is fully guaranteed for 12 (12) months of the date of purchase against errors arising from manufacture or materials. This guarantee does not remove, but is in encore to, your legal rights.
Service to the controller or battery charger must be done by your competent Pride Supplier. Any attempt to open or dismantle these parts will render the warranty void.
NON-GUARANTEE This guarantee does not extend to those items that may need replacement by normal use (bands, belts, lamps, vinyl, plastic, motor brushes, fuses, and batteries), or damage to this product due to abuse or accident for which Pride or the agent of Pride cannot be held responsible. This guarantee does not include any employment or call.
BATTERIES Batteries are guaranteed for six (6) months. Slow decline in service because the battery is left in a discharged condition, is left under cold conditions for a long period of time or worn out by heavy use is not included.
SERVICE CONTROL AND WARRANTY SERVICE Warranty service can be done by a competent Pride Supplier. Please contact your competent Pride Supplier for advice on the current price of a service visit.
REPLACE UNITS The availability of a replacement unit and/or spare parts depends on the discretion of the supplier, not the manufacturer. For more information about replacement units and/or spare parts, please contact your competent Pride Supplier.



Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.