EN
PowerTech logo
Official user manual

PowerTech 52CC

31 pages·471 KB·Chainsaw·PDF·ENDEFRITNLJA
PowerTech 52CC
Table of Contents 4 sections User manual NL KETTINGZAAG 52CC · 2. labels on the machine · 6. fuel and lubrication · 10. maintenance to sword and chain ShowHide
Page 1 of the PowerTech 52CC user manual — User manual NL KETTINGZAAG 52CC
Page 1 · click to enlarge
Page 1

User manual NL KETTINGZAAG 52CC

Page 2 of the PowerTech 52CC user manual — User manual NL KETTINGZAAG 52CC
Page 2 · click to enlarge
Page 2

! SAFETY Instructions with one ! are important points and must be observed to avoid injuries. For this we ask you to read these instructions carefully, and all follow them. . Safety points in the operating manual

These instructions must be followed to prevent accidents

These instructions must be followed to avoid mechanical problems.

These instructions may be useful when using the product.

1. What is true 2) Labels on the machine 3) Symbols on machine 4) Safety measures 5) Mounting of chain and sword 6) Fuel and chain oil 7) Operation of machine 8) Saw 9) Maintenance 10) Maintenance of chain & sword 11) Specifications

! attention · Please note

Page 3 of the PowerTech 52CC user manual — User manual NL KETTINGZAAG 52CC
Page 3 · click to enlarge
Page 3
1. 1) lever of chain brake 2) handle of drawstring 3) air filter 4) choke 5) safety button gas lever 6) handle behind 7) hand lever 8) lockbutton for gas lever 9) switch 10) fuel tank 11) oil tank 12) front lever 13) chain 14) sword
PowerTech 52CC — User manual NL KETTINGZAAG 52CC diagram (page 3)
Fig. 1 · User manual NL KETTINGZAAG 52CC
Page 4 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 4 · click to enlarge
Page 4

2. labels on the machine

PowerTech 52CC — 2.  labels on the machine diagram (page 4)
Fig. 2 · 2. labels on the machine

Read the instructions

the use of this machine

PowerTech 52CC — 2.  labels on the machine diagram (page 4)
Fig. 3 · 2. labels on the machine

Wear head, ear and eye protection.

Use 2 hands to operate the chainsaw

PowerTech 52CC — 2.  labels on the machine diagram (page 4)
Fig. 4 · 2. labels on the machine
PowerTech 52CC — 2.  labels on the machine diagram (page 4)
Fig. 5 · 2. labels on the machine

Watch this! - Can hit back.

PowerTech 52CC — 2.  labels on the machine diagram (page 4)
Fig. 6 · 2. labels on the machine

Attention! Attention!

Page 5 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 5 · click to enlarge
Page 5

Never adjust the product. If you have modified the product and then use it, all rights lapse.

3. symbols on the machine For safe use and maintenance there are symbols created on the machinery. Use the right resources in the right place.

a. The fuel refill opening

Locationfuel tank
Locationoil cap

b. The opening to refill chain oil.

c. Indication of the on/off switch

Locationback left

b. Indication of the choke.

Locationrear right

for adjustment of the chain Place: at the bottom of the necklace brake

e. Indication of the button to the oil

PowerTech 52CC — 2.  labels on the machine diagram (page 5)
Fig. 7 · 2. labels on the machine

f. The position of the H needle

Position of the L needle

Page 6 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 6 · click to enlarge
Page 6

Position of the stationary set screw Place: back left

4. safety measures for the use of machinery a. first read the user manual
PowerTech 52CC — 2.  labels on the machine diagram (page 6)
Fig. 8 · 2. labels on the machine

b. to be able to use the machine safely.

Never use the machine, under the influence of alcohol, in case of fatigue or sleep deprivation, after using medicines that may affect the ability to estimate

c. Never start the machine indoors.

The exhaust gases contain harmful carbon monoxide.

b. Never use the machine

under the following circumstances:a. If the ground is smooth or if there is

no stable position can be maintained. b. at night or in close fog,

or at any other time that is obstructing the work area. c. During storms of thunder,

rain and wind.

e. Learn to use the machine

from an experienced person. f. Deficiencies in sleep, fatigue or mental illness

fatigue leads to concentration deficiency, which can lead to accidents again. Use the machine in sessions of about 10 minutes and take

Page 7 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 7 · click to enlarge
Page 7

then 10-20 minutes of rest. It is better to use the machine no more than 2 hours a day.

g. It is wise to take this

To keep instructions on the machine, should questions arise.

h. Add this manual as

the machine is loaned out or sold.

i. Let children or people take this

do not use the manual.

  • protection and clothing 1. When using the product, protective agents must be worn as:
1. Helm 2. Safety glasses or face protector 3. Fat work gloves 4. Anti-slip work shoes 5. Hearing protectors
PowerTech 52CC — 2.  labels on the machine diagram (page 7)
Fig. 9 · 2. labels on the machine
2. It's wise to have a. Attached tools and manual b. Fuel for chainsaw and chain oil c. Signals (roep, plates) d. Flute (to attract attention) e. Axe (for removing obstacles) 3. Never use the product if shorts or sandals are worn.
Page 8 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 8 · click to enlarge
Page 8
PowerTech 52CC — 2.  labels on the machine diagram (page 8)
Fig. 10 · 2. labels on the machine
  • attention to fuel use a. The engine of the machine is made to mix fuel

walk. This contains highly flammable gasoline. Do not store the cherrycans in a room where a boiler,

gas stove or stove are placed. Also, do not store them in a room where sparks can occur or anything else that could ignite the fuel. b. During operation of the machine or refueling it is

It's dangerous to smoke. Keep the inflamed cigarette away from the machine at all times. c. Make sure that the machine is switched off during refueling. Look

then whether there is no open flames or sparks nearby. b. If spilled during refilling, the spilled

wipe fuel with a dry cloth before turning the machine back on. e. After refueling, close the cap of the fuel tank again

Turn. After this the machine approx. Move 3 meters from the place where refueled was before starting.

  • before starting the engine never look at the working environment start sawing until there is a free workplace. This

also keeps in a free path of the falling tree be careful and keep spectators and animals away

from the workplace. The distance must be about 2.5 times the size of the object to be sawed. Inspect the machine for wear, loose or broken

parts. Never use the machine if it is broken or if it has been put together wrongly. Make sure the chain stops when the gas is released.

PowerTech 52CC — 2.  labels on the machine diagram (page 8)
Fig. 11 · 2. labels on the machine
  • during engine startup

Always keep the machine firm with 2 hands cast as well

Machine running.

Page 9 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 9 · click to enlarge
Page 9

Keeps all parts of the body away from the running engine. Before starting, check if the chain is running completely free.

  • In-use

Keeps the handles free of oil and fuel Do not touch exhaust, spark plug or other metal parts during use or immediately after use. There is a risk of electrocution or severe burns.

Be extremely careful with cutting small bushes or twigs. Bending material can be grabbed by the chain and drawn towards user that may thus become imbalanced. Be careful when sawing a branch, it may get stressed and break. Look before cutting a tree if there are dead branches in it. These may fall out during sawing. Always turn off the engine before you move the machine. . safety measures for users in the event of impact.

Retrospective action can occur when the top of the sword touches an object,

or if the wood sticks around the chain. When touching an object with the top of the sword a furiously rapid reaction can occur, in this response the sword will soon return to its user. If the chain is clamped by wood, there is a chance that the user will be drawn towards object. In either case, the user may lose control and suffer injuries. Do not blindly rely on the safety measures of the machine.

As a user, you must take the following steps to keep your workplace free from accidents:

! attention

Page 10 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 10 · click to enlarge
Page 10

1. By understanding the principle of backlash, users cannot be surprised quickly. Surprises contribute to the number of incidents. 2. Always hold the saw firmly with 2 hands with a running motor. Right hand on the rear handle and left hand on front. A firm grip reduces the risk of a backlash and a good maintenance of control. 3. Make sure the workspace is clear of obstructions. Do not let the top of the sword come into contact with any branch or other object during sawing. 4. Always cut with a high speed. 5. Never cut out of reach or above your shoulders. 6. Follow the manufacturer's instructions for maintenance and grinding of the chain. 7. Use only the same or similar chains and swords.

  • maintenance To maintain the machine in good condition there must be regular

maintenance. Follow the instructions of the manual for this maintenance. Always stop the engine when maintaining the machine.

The metal parts are hot right after using the machine.

Leave all maintenance that is not in the operating manual to

a specialist.

  • transport Always transfer the machine with a stopped engine. The sword must be in the protective casing and pointing backwards. Make sure the exhaust does not come into contact with the body.

! attention

Page 11 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 11 · click to enlarge
Page 11
5. Installing the sword and chain A standard package for a chainsaw contains the following parts:
1. Engine 2. Protection casing for the sword 3. The Sword 4. The chain 5. - Bug key six. Screwdriver for adjusting the carburetor 7. File and mounting screws
PowerTech 52CC — 2.  labels on the machine diagram (page 11)
Fig. 12 · 2. labels on the machine

After opening the box, the sword and chain can be mounted in a following manner.

! attention The necklace has sharp ends. Wear thick work gloves for safety.

1. Pull the chain brake to the front handle so that the chain brakes are not on it. 2. Unscrew the nuts and remove the chain cabinet. 3. Put the chain around the gear, and put the sword over the 2 pins. Make sure the hole in the sword is at the bottom. Adjust the chain tensioner so that it is aligned with the hole in the sword.
Page 12 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 12 · click to enlarge
Page 12
PowerTech 52CC — 2.  labels on the machine diagram (page 12)
Fig. 13 · 2. labels on the machine
8. Hole in the Sword 9. Propeller 10. Chain housing

Make sure the chain is properly mounted. 1. Turn direction. Figure F3

PowerTech 52CC — 2.  labels on the machine diagram (page 12)
Fig. 14 · 2. labels on the machine

4. Put the chain cabinet back in place and turn on the nuts hand-fast. 5. Adjust the tension on the chain while holding up the sword a little bit. If the inside of the chain at the bottom of the sword is just touches, tension is good. 6. Turn the nuts firmly (12-15 N/m). check that the chain is running smoothly by moving it manually. If necessary, the voltage can be adjusted but the chain cabinet must be unscrewed. 7. Turn the chain tensioner.

Watch this.

Page 13 of the PowerTech 52CC user manual — 2.  labels on the machine
Page 13 · click to enlarge
Page 13
PowerTech 52CC — 2.  labels on the machine diagram (page 13)
Fig. 15 · 2. labels on the machine
2. loose 3) fixed 4) chain tensioner

A new necklace will stretch at first. Check and adjust the tension if necessary. A chain too loose will soon end up on the sword.

Watch this.

Page 14 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 14 · click to enlarge
Page 14

6. fuel and lubrication

  • fuel Mix a normal gasoline with good quality 2-stroke oil. Recommended mix ratios Up to 20 hours use gasoline 20:1 oil After 20 hours of using petrol 25:1 Oil
PowerTech 52CC — 6.  fuel and lubrication diagram (page 14)
Fig. 16 · 6. fuel and lubrication

Mix ratio 25:1 Petrol (l) 1 2 3 4 5 2-stroke oil (ml) 40 80 120 160 200 ! attention Keep open fire away from the place where fuels are treated and or stored Mix and store fuel only in a fuel approved cherrycan Note Most engine problems are used directly or indirectly caused by the fuel. Be careful not to mix motor oil or 4-stroke oil.

  • Chain oil Use engine oil SAE 10W-30 throughout the year.
PowerTech 52CC — 6.  fuel and lubrication diagram (page 14)
Fig. 17 · 6. fuel and lubrication

Note Do not use any used oil, this can cause damage to the oil pump.

Page 15 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 15 · click to enlarge
Page 15
PowerTech 52CC — 6.  fuel and lubrication diagram (page 15)
Fig. 18 · 6. fuel and lubrication
7. operation of the engine . .

a. Fill the fuel tank and

oil tank, and turn off the caps. Figure F7 b. Turn on/off switch

PowerTech 52CC — 6.  fuel and lubrication diagram (page 15)
Fig. 19 · 6. fuel and lubrication

The I stand. Figure F8 c. Hold the gas with the

a button intended for use with the device. Figure F9d. Take off the choke. Figure F10 e. Pull the starter cord while

The machine is on the ground. Figure F11 f. If the engine starts, it can be

PowerTech 52CC — 6.  fuel and lubrication diagram (page 15)
Fig. 20 · 6. fuel and lubrication

Choke gets pushed back. g. Keep the engine warm

The Commission has already taken a decision on this matter.

1. Chain oil 2. Mix fuel 3. On/off switch 4. Button to secure the gas 5. Gas lever 6. Safety throttle 7. Choke Note When restarting a stopped machine, no choke need be used. attention Do not start the chainsaw held in hand. This allows the chain to come into contact with the body. Do not touch the chain when the engine is running, this can turn on its own.
PowerTech 52CC — 6.  fuel and lubrication diagram (page 15)
Fig. 21 · 6. fuel and lubrication
PowerTech 52CC — 6.  fuel and lubrication diagram (page 15)
Fig. 22 · 6. fuel and lubrication

!

Page 16 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 16 · click to enlarge
Page 16
  • Checking the Oil

stock After starting the engine, rotate the chain in a medium position and see if oil comes off. See Figure F12 1. Chain oil

PowerTech 52CC — 6.  fuel and lubrication diagram (page 16)
Fig. 23 · 6. fuel and lubrication

The amount of oil can be adjusted by adjusting the adjustment screw at the bottom of the engine. See Figure F13 1. Propeller Pay attention The oil tank for the chain will be almost out when the fuel is also running out. Fill the oil tank every time it is filled.

PowerTech 52CC — 6.  fuel and lubrication diagram (page 16)
Fig. 24 · 6. fuel and lubrication
  • Adjusting the carburetor The carburator that is on the machine is adjusted in the factory, but can still be tuned to your own wishes. Before adjusting, make sure the filters are clean and the fuel is well mixed. Take the next steps to adjust the carburetor. Note Adjust the carburetor with the sword and chain mounted. Stop the engine and twist in all of the H needle and L needle. Then turn the: H needle 1 3/4 stroke L needle 1 1⁄4 stroke Start the engine and let it warm up (not full gas)
Page 17 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 17 · click to enlarge
Page 17

Turn the L needle slowly clockwise, to a position where the engine is maximum idle. Now turn back the L needle 1⁄4 stroke. Now turn the motor's screw against the clock so that the chain does not rotate. If the engine is stationary too slowly, turn clockwise. Now try the saw and set the H needle for most power, not at highest speed.

PowerTech 52CC — 6.  fuel and lubrication diagram (page 17)
Fig. 25 · 6. fuel and lubrication

1. L-needle 2. H-point 3. Stand-off screw . anti-freeze mechanism on the carburetor Regular operation of the chainsaw at temperatures 0-5°C or with high humidity can cause ice formation in the carburetor. This may result in the engine providing little power or not working at all. This machine is designed to provide a ventilation hole behind the air filter, so that hot air can flow into the engine and no ice formation can occur. Under normal conditions, the machine can be used as it came from the factory. If the machine is used where ice formation can occur it should be put in the antifreeze setting before use. (Figure F15)

Page 18 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 18 · click to enlarge
Page 18
  • how to switch to the other setting Turn on/off switch in off mode. Remove the air filter housing from the machine. Turn the screw off on the back of the housing and remove the net. Turn the net and mount it again, so that the antifreeze plate is on the right.
1. Air filter housing 2. Antifreeze plate 3. Screw 4. Normal setting 5. Antifreeze setting 6. Net
PowerTech 52CC — 6.  fuel and lubrication diagram (page 18)
Fig. 26 · 6. fuel and lubrication

Using the machine in antifreeze setting while temperatures have risen may cause the engine to not start, or that the engine doesn't keep running properly during use. Make sure the setting is correct. When used in antifreeze setting, regularly consulate the air filter on sawdust.

! attention

Page 19 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 19 · click to enlarge
Page 19
  • Chain brake This machine is equipped with an automatic brake that stops the chain when a backstroke is applied. The brake automatically starts when too high forces come on the sword. This brake can also be manually operated by pushing the lever of the chain brake to the sword. To lift the brake pull the lever back.
PowerTech 52CC — 6.  fuel and lubrication diagram (page 19)
Fig. 27 · 6. fuel and lubrication

Please note Check daily the operation of the brake. How to check? Stop the engine Hold the chainsaw horizontally me 2 hands and let go of the front hand. Let the top of the sword hit a stump from a tree, with which the brake must enter into force. Figure F18

PowerTech 52CC — 6.  fuel and lubrication diagram (page 19)
Fig. 28 · 6. fuel and lubrication

If the brake does not work, have it checked by your dealer. The engine will heat the clutch, when the brake is switched on at high speeds, causing problems. If the brake is switched on during use, release the throttle immediately and let the engine run idle.

Page 20 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 20 · click to enlarge
Page 20
  • Stopping the engine Release the throttle and let the motor run idle for a few minutes. Turn the on/off switch into O position Figure F19
PowerTech 52CC — 6.  fuel and lubrication diagram (page 20)
Fig. 29 · 6. fuel and lubrication
1. on/off switch
Page 21 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 21 · click to enlarge
Page 21

8. Saws ! Attention Read the chapter "Safe" before you start. It is recommended to first saw a few easy pieces. This is to get used to the machine. Always follow the safety rules. The chainsaw is only to be used for sawing wood. There's no need to exert a lot of power on the chainsaw. Use a little force and let the engine run at full speed. If the chain is stuck in the sawcut, try not to pull it loose but use a wedge in the cut.

  • Retro-return protection This chainsaw is made with a chain brake which will enter into force in normal conditions when a backlash occurs. Check the brake before use, by pressing full power the chain brake towards the sword. The chain must stop spinning with the engine on full rev. If the chain does not stop or stops slowly, the brake tyre and clutch must be replaced. It is very important to check the brake and sharpness of the chain for each use in order to prevent backlash. Removing safety, insufficient maintenance or improper assembly of the sword or chain, can lead to personal injury due to impact.
PowerTech 52CC — 6.  fuel and lubrication diagram (page 21)
Fig. 30 · 6. fuel and lubrication
  • Felling a tree Determine the direction to which the tree should fall, taking into account the wind, location of heavy branches and ease of working on the ground after skinning. Clear the ground from branches and bushes. Also clear a escape path. Saw a wedge in 1/3 of the thickness of the tree on the side where the tree should fall. Saw the tree from the other side, slightly higher than the tip of the wedge. (Figure 22)
Page 22 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 22 · click to enlarge
Page 22
PowerTech 52CC — 6.  fuel and lubrication diagram (page 22)
Fig. 31 · 6. fuel and lubrication
1. Wig 2. Sheeting cut 3. Fall in! Please note that if a tree is felled, please inform fellow guinea fowls and bystanders. ! Watch this.

Get a firm position, never stand on the tree. Be alert for a rolling tree, all the way up on a slope. Follow the instructions in Chapter . Sawing wood on the ground. Cut the tree trunk halfway and turn it around. Then cut the tree trunk from the other side. Figure F23.

PowerTech 52CC — 6.  fuel and lubrication diagram (page 22)
Fig. 32 · 6. fuel and lubrication

Sawing a hanging tree trunk. Saw the tree trunk for 1/3 from the bottom in area A and then cut through from the top. Swipe the trunk for 1/3 from the top in area B and then continue from the bottom. Figure F24

PowerTech 52CC — 6.  fuel and lubrication diagram (page 22)
Fig. 33 · 6. fuel and lubrication
Page 23 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 23 · click to enlarge
Page 23

Sawing branches or fallen trees. First check which way the branch is bent. First, cut the side where the branch is curved and then saw in the other side. Figure F25

PowerTech 52CC — 6.  fuel and lubrication diagram (page 23)
Fig. 34 · 6. fuel and lubrication

! Beware of jumping back from a sawn branch. Sawing branches on a standing tree. Saw the branch from the bottom and then saw it from the top feather. Figure F26

PowerTech 52CC — 6.  fuel and lubrication diagram (page 23)
Fig. 35 · 6. fuel and lubrication

! Note Do not use unstable ladder. Do not cut out of your reach Do not see above shoulder height Always hold the saw with 2 hands

Page 24 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 24 · click to enlarge
Page 24
9. Maintenance! Be sure that the engine is off and cooled during inspection or maintenance. Unplug the spark plug to prevent startup.
  • maintenance after each use 1. Air filter Dust on the air filter can be removed by tapping a corner of the filter onto a hard surface. To remove dirt from the mesh, open the filter and clean both sides in petrol. Then blow the gauze with air pressure clean and dry from inside. Figure F27 Press the edges of the filter against each other until a click is followed to put the filter back together.
PowerTech 52CC — 6.  fuel and lubrication diagram (page 24)
Fig. 36 · 6. fuel and lubrication
2. Arm Get the sword off the machine and check for lubrication. Figure F28
PowerTech 52CC — 6.  fuel and lubrication diagram (page 24)
Fig. 37 · 6. fuel and lubrication
Page 25 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 25 · click to enlarge
Page 25
1. Smear point
3. The sword Remove the sawdust from the groove of the sword when it is loosened. Figure F29
PowerTech 52CC — 6.  fuel and lubrication diagram (page 25)
Fig. 38 · 6. fuel and lubrication

Apply the gear to the top of the sword. Figure F30

PowerTech 52CC — 6.  fuel and lubrication diagram (page 25)
Fig. 39 · 6. fuel and lubrication
1. oil point 2. Lubricant 3. Gear
4. Other check the fuel tank for leakage, whether there are nuts loose and if any damage is caused. If any defects have been detected, make sure they are corrected for use next time.
  • Periodic maintenance Cooling fins of the cylinder Dump between the cooling fins in the cylinder can cause the engine to overheat. Therefore, check the cooling fins regularly and remove the dirt between them. When placing the caps back, make sure that all cabling is in the right place. Figure F31
PowerTech 52CC — 6.  fuel and lubrication diagram (page 25)
Fig. 40 · 6. fuel and lubrication

Attention

Page 26 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 26 · click to enlarge
Page 26

Don't let dirt get into the air intake. Fuel filter Remove the filter from the fuel filling hole. Remove the filter and clean it with petrol or replace it with a new one if necessary. Figure F32

PowerTech 52CC — 6.  fuel and lubrication diagram (page 26)
Fig. 41 · 6. fuel and lubrication
1. Fuel filter Attention Keep the filter clean. Oil tank Remove the oil filter from the filling opening of oil and clean it with gasoline. When placing the filter back, make sure that it appears in the corner on the right. Figure F33
PowerTech 52CC — 6.  fuel and lubrication diagram (page 26)
Fig. 42 · 6. fuel and lubrication
2. Oil filter Bug Clean the electrodes with a steel brush. If necessary, make the opening 0,65mm. Figure F34
PowerTech 52CC — 6.  fuel and lubrication diagram (page 26)
Fig. 43 · 6. fuel and lubrication
Page 27 of the PowerTech 52CC user manual — 6.  fuel and lubrication
Page 27 · click to enlarge
Page 27

Gear Check the gear for break and whether there has been wear that can get in the way of the chain drive. If there has been wear, replace the gear. Never use a new necklace to make an old gear or vice versa. Figure F35

1. Gear 2. Bullet bearing three. - Clutch, bus four. Distance holder 5. Shoot
PowerTech 52CC — 6.  fuel and lubrication diagram (page 27)
Fig. 44 · 6. fuel and lubrication

Front and rear dampers Replace if there are cracks in the rubber.

Page 28 of the PowerTech 52CC user manual — 10.  maintenance to sword and chain
Page 28 · click to enlarge
Page 28

10. maintenance to sword and chain

  • The necklace! Pay attention It is important to keep the saw teeth sharp. The saw teeth should be cut as: Sawdust becomes powdery Additional power is needed to see The sawcut does not go straight Vibrations increase Fuel consumption increases ! Watch Using work gloves For filing: Make sure the chain is secure Make sure that the engine is off Use the correct file. Place the file on the saw tooth and push it straight forward. Figure F36
PowerTech 52CC — 10.  maintenance to sword and chain diagram (page 28)
Fig. 45 · 10. maintenance to sword and chain
Page 29 of the PowerTech 52CC user manual — 10.  maintenance to sword and chain
Page 29 · click to enlarge
Page 29

After each tooth is filed, check if there has been a sufficiently deep filing. Figure F37

PowerTech 52CC — 10.  maintenance to sword and chain diagram (page 29)
Fig. 46 · 10. maintenance to sword and chain

Make sure that the edges of each tooth are the same size and angle. Figure F38

PowerTech 52CC — 10.  maintenance to sword and chain diagram (page 29)
Fig. 47 · 10. maintenance to sword and chain
Page 30 of the PowerTech 52CC user manual — 10.  maintenance to sword and chain
Page 30 · click to enlarge
Page 30
  • The Sword Turn the sword occasionally, to prevent wear on one side. The corners of the sword must always be square inside and outside. If a ruler is laid along the sword and a tooth, there must be a small opening; if not then the sword should be replaced. Figure F39
PowerTech 52CC — 10.  maintenance to sword and chain diagram (page 30)
Fig. 48 · 10. maintenance to sword and chain
1. Ruler 2. Opening 3. No opening 4. Chain heals over.
Page 31 of the PowerTech 52CC user manual — 10.  maintenance to sword and chain
Page 31 · click to enlarge
Page 31
11. Engine specifications:

Fuel: mix (petrol 25 : 2-stroke oil 1) Fuel tank content (ml): 550 Chain oil: 10W-30 Oil tank content: 260 Carburator: diaphragm type Inflammation: direct Bug: G455AVS Champion CJ-7Y G500AVS CJ-6Y Champions Oil supply: automatic pump with adjustment Gear (tooth x stitch) 7T x 0.325 Dimensions (l x h x b) (mm) 410 x 235 x 265 Net weight engine (kg): 5 Sawing part Sword: with gear Size (in.): 14,16 standard Necklace: Oregon 21BP/21VB Pitch (in: 0,325 Thickness (in): 0,059 The specifications cannot be derived rights.

Ask about the PowerTech 52CC

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the PowerTech 52CC

Be the first to ask — other owners or our team will answer.

Original document

PowerTech 52CC manual PDF

31 pages·471 KB·Chainsaw·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…