

Antenna Emergency Call Indicator VOX Channel Ring Hole PTT Monitor/FM+
FM- MIC Battery snap Battery SP MIC/SP Waterproof Cover Belt Clip

Transmit Press the “PTT”key, the red indicator on, then you can talk at once. Release your hands to end the talking.
Monitor Press the”Radio/Monitor/Reception+”key shortly to open the acous- tic noise, and then press the key again to exit.
Call Press PTT, then “Radio/Monitor/Reception+” key shortly to activate call function. Release the “Radio/Monitor/Reception+” key to exit.
Press the “Radio/Monitor/Reception+” key for about 2 seconds to open theRadio function, then press the “Radio/Monitor/Re- ception + ”or “Call/Reception-” key shortly to scan the signal automatically. The transceiver will stop scanning and to receive when there’s a signal on the channel, press the ”Radio/Monitor/ Reception+”orCall/Reception-” key shortly again to receive other radios. Keep pressed the “Radio/Monitor/Reception+” to exit the radio mode, When the speaker sound “di,di” that’s means you already exit. PC also can be programmed to turn off FM.
Emergency Channel Operation (Emergency Call Function) Work III set a useful function “Emergency Call”. Press the “Call/Re- ception-” key for about 2 seconds to activate emergency call func- tion, then the indicated light flashes red and alert to transmit to the radio which is set the same frequency. Press the PTT key to cancel The transceiver will remain at channel 01 when you operate the Emergency Call Function, until rotate the channel selector to your desired channel. The green indicated light will flash if you didn’t rotate the channel selector after operating the Emergency Call Function.
Battery low voltage detection
The device works properly when the voltage is higher than 6.5V; When the voltage is among 6.3V to 6.5V, the transceiver receives nor- mally but with alerts and “dididi” sound indication every 20 seconds and launches normally, but the light flashes red while launching.
FM Radio

When the voltage is below 6.1V, then the transceiver will power off by itself.
Wired Cloning between two transceivers
Well connected the transmission lines to the both transceivers, and then power on the subsidiary transceiver. Rotate the channel selector on the base transceiver to channel 8, then hold and Press “Radio/Monitor/Reception+” key to power on, (3 seconds later) until the orange light (red light and yellow light flash simultaneously) flashes which indicates the base trans- ceiver is in cloning state, then release the button. When the orange light on the base transceiver flashes, press the PTT key, the red light on base transceiver flashes, and the yellow light on subsidiary transceiver flashes, which indicates the base transceiver is in cloning state. The mutual clone is successful when the light on base transceiver flashes orange again. If indicator lights of both two transceivers flashes abnormally in the process of data transmit, it means replication fail. In that case, please check and make sure the transmission line is well connected. And please press the PTT button again to resume cloning when the indicator light of the base transceiver shines orange. If need to clone with more than one transceiver, please turn off the subsidiary device after cloning finished and then pull out the transmission cable. And then clone to next transceiver following steps above. Please reboot the transceiver to make it work properly after cloning.

Maintenance Transceiver you purchased is an exactitude design electronic prod- ucts and pleaseuseitcarefully. Following maintenance ways may help extend its lifetime.
Please don’try to disassemble the transceiver since non-techni- cians’ processing may cause damage to the device. To use stable power supply, please connect the specified USB cable to the DC jack of the transceiver. Please turn off the transceiver when you are in gas station. Please don’t put the transceiver in sun or hot place for long time, because the high temperature will shorten use life of electronic parts and cause distortion to plastic parts. Please keep the transceiver dry, because rain and moisture will erode the electronic circuits. Please power off the transceiver and remove its battery pack im- mediately once it is peculiar.

No power The battery may have been exhausted. Please recharge or replace the battery pack. The battery pack may not be installed correctly. Please check and install it again.
Battery lasts in a short time after charging
The battery pack has been used out and cannot function any longer. Please replace it with a new one. Make sure the battery is fully charged.
Unable to talk or hear members in your group
Make sure you are using the same frequency and CTCSS tone as other members in your group. Other group members maybe too far away from you, make sure you are in the radio’s operating range.
The other group members’ voices are present on the channel.
Please change the frequency. Make sure to change CTCSS signal of all transceivers in your group.

50 groups DCS 023 051 114 143 174 251 315 371 445 532 631 723 025 054 115 152 205 261 331 411 464 546 632 731 026 065 116 155 223 263 343 412 465 565 654 732 031 071 125 156 226 265 346 413 466 606 662 734 032 072 131 162 243 271 351 423 503 612 664 743 043 073 132 165 244 306 364 431 506 624 703 754 047 074 134 172 245 311 365 432 516 627 712
83 groups CTCSS 67.0 85.4 107.2 136.5 165.5 186.2 210.7 254.1 69.3 88.5 110.9 141.3 167.9 189.9 218.1 71.9 91.5 114.8 146.2 171.3 192.8 225.7 74.4 94.8 118.8 151.4 173.8 196.6 229.1 77.0 97.4 123.0 156.7 177.3 199.5 233.6 79.7 100.0 127.3 159.8 179.9 203.5 241.8 82.5 103.5 131.8 162.2 183.5 206.5 250.3

General Frequency range 446,00625 - 446,09375 MHz Number of channel 8 + 8 Channel spacing 12.5 kHz Operatingtemperaturerange da -20°C a +55°C Modem pattern Frequency Modulation (FM) Voltage 7,4 V Standby Current 15mAh (Power Save) Size 100 (H) × 58 (L) × 36 (P) mm Weight 205 g Transmitter Frequency Distortion ≤3 ppm Output power ≤500 mW Emission current 450 mA Maximum frequency deviation ±2,5 kHz Audio frequency distortion


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.