EN
Life-Mobility logo
Official user manual

Life-Mobility Plus

51 pages·1.7 MB·Wheelchair·PDF·ENITJA
Life-Mobility Plus
Table of Contents 21 sections Contents · Safety instructions · Delivery Check Safety instructions · Technical specifications · … ShowHide
Page 3 of the Life-Mobility Plus user manual — Delivery Check Safety instructions
Page 3 · click to enlarge
Page 3

Delivery Check Safety instructions

its own momentum. n n Do not turn the wheelchair around on a steep slope. If the wheelchair is facing across a steep slope, it can very easily tip over. n n Always keep your speed under control when going downhill. n n The accompanying person must reduce the speed of the wheelchair using the push-handles. n n If you are operating the wheelchair yourself, slow the wheelchair down using your hands on the handrims only. Never use the brake as this can cause you to lose control of the wheelchair.

Delivery Check Before you start to use it, check that the delivered wheelchair matches the product description on page 11. If you notice any damage caused during transport, please inform your dealer. We at Life & Mobility are sure that your Plus will meet your expectations and we wish you every success with it.

Other Warning:

n n Do not leave the wheelchair in direct sunlight: the upholstery can become hot, causing burns or oversensitivity of the skin.

Take care:

n n Do not allow the wheelchair to come in contact with seawater: seawater is aggressive and will corrode it. n n Do not allow the wheelchair to come in contact with sand: sand can penetrate the rotating parts of the wheelchair, causing unnecessarily rapid wear.

Page 4 of the Life-Mobility Plus user manual — SH
Page 4 · click to enlarge
Page 4

Technical specifications

Product description

n n Seat width (SW): 37 / 42 / 47 / 52 / 57 / 62 cm n n Seat depth (SD): 44 / 48 cm n n Seat height (SH): 46,5 / 48 / 51 / 56 / 59 cm n n Armrest height (AH): 23 cm n n Width of wheelchair (WW): 62 / 67 / 72 / 77 / 82 / 87 cm n n Width of wheelchair folded up (including wheels) 37 cm n n Height of push-handles (HP): 95 cm n n Lower leg length (LL): 38-49, 40-51 cm n n Seat angle: 3 / 6° n n Backrest angle adjustment: 89 / 97 / 110 ° n n Total weight: 28 kg n n Lift weight: 14 kg n n Maximum user weight: 150 kg*

Life-Mobility Plus — Technical specifications diagram (page 4)
Fig. 1 · Technical specifications

Product description 1. Push-handle 2. Matrixx backrest 3. Standard side 4. Matrixx seat 5. Matrixx legrest 6. Foldable frame 7. Front wheel (semi-solid) 8. Tyre brake 9. Rear wheel (pneumatic) 10. Quick Release axle 11. Tipping lever 12. Handrims 13. Backrest adjuster

SW

WW

Life-Mobility Plus — SW diagram (page 4)
Fig. 2

SD

9 10 8 11

AH

Not illustrated:

HP

n n User manual

Life & Mobility recommends using the wheelchair in an ambient temperature of between -5 °C and +40 ° C.

SH

This manual describes the standard products. This wheelchair can be extended with many options and accessories, these are listed under ‘Options’.

* If the user weights more than 150 kg, the Plus can be strengthened on request. Please fill in a supplementary form to request the adaptation.

centre line of chair

Expected service life Life & Mobility assigns a service life of 7 years to this product. This means that during this period, the product is fixable, safe and usable.

The statement above is only applicable if the user uses the product in the manner that Life & Mobility intended, marked with CE and including any original accessories.

Cross section through

Page 5 of the Life-Mobility Plus user manual — Options
Page 5 · click to enlarge
Page 5

Options

Options

Options (not illustrated) In addition to the standard parts, the following options are available for this wheelchair:

- Support seat - Hip seat

n n Backrest - Torso supports - Soft backrest - Anatomical backrest - Comform backrest - Comfit backrest - Invito backrest

n n Frame - Non-foldable frame

n n Push-handles - Height-adjustable push handle

n n Brake - Extended tyre brakes

n n Legrests - Comfort legrest (with heel strap) - Knee cushion - Plaster cast legrest - Stump support, adjustable angle

n n Wheels - Front wheels with pneumatic tyres - Rear wheels with semi-solid tyres

n n Seat depth - Rear extension set seat and backrest (4 cm)

n n Armrests - Padded long armrests - Armrest for hemiplegics

n n Sides - Standard extended sides (3 cm) - Sides with height-adjustable armrests - Extended sides (3 cm) with height-adjustable armrests

n n Headrest - Standard headrest, small - Flexible headrest - Snellius headrest

n n Worktops - Perspex worktop - Wooden worktop - College worktop - Elbow padding

n n Accessories (not illustrated) - Drum brakes operated by accompanying person - Locking set for sides - Stick holder - Anti-tipping supports - Taxi attachment for Delta bracket - Spoke protectors - Hoop covers - Support plates for footrests - Abduction block - Seat belt - Front extension set for swivel casters - Matrixx Cleaner

n n Seat - Memory foam seat - Plank seat (with lip) - Contour seat - Contour+ seat - Contour Gel seat

Page 6 of the Life-Mobility Plus user manual — A
Page 6 · click to enlarge
Page 6

Settings and adjustments

Settings and adjustments

Life-Mobility Plus — Settings and adjustments diagram (page 6)
Fig. 3 · Settings and adjustments

The wheelchair has a wide range of settings and adjustment options with which the chair can be adjusted to match your own requirements. Life & Mobility recommends that you consult your dealer with regard to the settings. You can easily make adjustments yourself.

Backrest angle adjustment The backrest can be set at three different angles: 90°, 70° and 50°. 1. Place your hands on the push-handles and squeeze the adjuster (A). 2. The hinged backrest can now be adjusted to the correct position. 3. Release the adjuster.

A

Life-Mobility Plus — A diagram (page 6)
Fig. 4

Adjusting the ride characteristics The ride characteristics of the wheelchair are adjustable. The rear wheels can be located in two different positions by moving the axle bearing. 1. Undo the large M16 nut (A) at the end of the axle bearing using a 24-mm spanner. 2. Remove the axle bearing and move it to the other axle hole (B). 3. Replace and tighten the M16 nut.

A B

n n Ensure that the left and the right push- handles are at the same angle.

Life-Mobility Plus — A B diagram (page 6)
Fig. 5

Removing and replacing the sides The sides are easy to remove. 1. Place you hand in the middle of the armrest. 2. Lift out the entire side. 3. Put the side in the holders. 4. Release the armrest.

Removing and replacing the rear wheels Note:

n n The brake must be disengaged to remove or replace the wheel.

Life-Mobility Plus — A B diagram (page 6)
Fig. 6

n n Ensure that the sides are fitted into the holders and not next to them. This can damage the sides and the wheels.

1. Press the release button in the middle of the hub (A). 2. Keep the pin pressed and remove the wheel. 3. Lay the wheel down axle-side up, so that the axle does not become dirty or damaged. 4. Replace the wheel in the axle hole (B). You will hear a click when the wheel is properly fitted. 5. Ensure that the wheel is correctly attached before you use the wheelchair again.
Life-Mobility Plus — A B diagram (page 6)
Fig. 7

B

Removing the legrests The legrests can be easily lifted from the frame by holding them above where they are fitted and lifting them out.

A

n n Ensure that the footrests have been folded away before you get out of the wheelchair. Never stand on the footrests. If you do, there is a chance that the wheelchair will tip over.

Show 5 more labels / short text on this page
Backrest angle · Ride characteristics · Sides · Fitting rear wheel · Legrests
Page 7 of the Life-Mobility Plus user manual — B
Page 7 · click to enlarge
Page 7

Settings and adjustments

Settings and adjustments

Life-Mobility Plus — Settings and adjustments diagram (page 7)
Fig. 8 · Settings and adjustments
Life-Mobility Plus — Settings and adjustments diagram (page 7)
Fig. 9 · Settings and adjustments

Adjusting the lower leg length 1. Unscrew the socket screw (A) one turn. 2. Set the legrest to the required lower leg length. Note: Ensure that the legrest is at least 5 cm from the floor. 3. Retighten the socket screw.

4. Lift the legrests out of the frame. 5. If necessary also remove the wheels. Note: Lay the wheel down axle-side up, so that the axle does not become dirty or damaged. 6. Place your hand around the middle tube (A) of the folding frame 7. Pull the frame upwards so that the sides move towards each other.

A

A

Locking the position of the ankle hinge

n n Adjust the ankle angle to the required position. n n Drill a hole in the hinge (A). n n Fix the ankle hinge using the fixing pin provided.

Life-Mobility Plus — A diagram (page 7)
Fig. 10
Life-Mobility Plus — A diagram (page 7)
Fig. 11

Removing and replacing the headrest* 1. Loosen the star knob. 2. Remove the headrest. 3. Insert the headrest in the holder. 4. Retighten the star knob.

Removing and replacing the backrest 1. Push the backrest forward at the top. 2. The backrest clips (A) will release from the push-handles. 3. Now release the bottom backrest clips (B). 4. The backrest can now be removed. When replacing the backrest, first press the bottom clips into position and then the top clips.

A

Inflating the tyres The tyres can be inflated using a bicycle pump. You received a valve nipple with the wheelchair that you can use to connect a pump. The correct tyre pressure is shown on the tyres.

Life-Mobility Plus — A diagram (page 7)
Fig. 12

A

To use the wheelchair comfortably, that is to say with the lowest possible rolling and turning resistance, it is important that the tyres are at the right pressure. The wheelchair will be more difficult to propel and manoeuvre if the tyre pressure is too low.

B

n n Always check whether the backrest is correctly attached before you sit in the wheelchair.

Life-Mobility Plus — B diagram (page 7)
Fig. 13

Recommendation To not jeopardise the guarantee, the manu facturer recommends having the dealer carry out these settings.

Removing and replacing the seat 1. Pull up the front of the seat. 2. Lift the seat out of the frame.

Folding the frame* 1. To be able to transport the wheelchair by car, you can fold the frame. 2. Remove the seat. 3. Remove the backrest.

Show 8 more labels / short text on this page
Lower leg length · Folding the wheelchair · Ankle angle · Headrest · Backrest · Seat · * if applicable · * if applicable
Page 8 of the Life-Mobility Plus user manual — EN18 EN19 EN19
Page 8 · click to enlarge
Page 8

Folding the wheelchair

Folding the wheelchair

Folding the wheelchair (Only if the wheelchair has a foldable inner frame) See also the Section ‘Settings and adjustments’.

8. Pull the middle tube of the folding frame upwards (see GB 16: Folding the frame) . The sides will move towards each other. The wheelchair is now folded.

n n Before using the wheelchair, check that all of the components of the wheelchair are correctly and securely installed.

n n Ensure that your fingers do not get caught when folding up the wheelchair. n n Always carry the wheelchair by the frame, never by other parts. n n Ensure that the wheelchair is completely unfolded before you use it.

Perform the steps below in the given order to fold the wheelchair, for instance for transport: 1. Remove the backrest from the back frame (see GB 16: Removing and replacing the backrest). 2. Lift the seat out of the frame (see GB 16: Removing and replacing the seat). 3. Remove the legrests from the frame (see GB 15: Removing the legrests). 4. Remove the sides with armrests from the frame (see GB 15: Removing and replacing the sides). 5. On both sides, push the release button of the Quick-Release axle and remove the rear wheels outwards (see GB 14: Removing and replacing the rear wheels). 6. Loosen the star knob and remove the headrest from the holder (if present) (see GB 17: Removing and replacing the headrest). 7. Squeeze the adjuster and push the push-handles towards the frame (see GB 15: Backrest angle adjustment).

EN18 EN19 EN19

Page 9 of the Life-Mobility Plus user manual — Use
Page 9 · click to enlarge
Page 9

Use

Use

Life-Mobility Plus — Use diagram (page 9)
Fig. 14 · Use

Transferring to and from the chair The Plus is a wheelchair for users with various handi- caps. Transfers from the wheelchair to, for example, a bed, toilet or shower and vice versa can be made in various ways.

Brakes The brakes of the wheelchair are correctly adjusted ex factory. Life & Mobility strongly recommends en- gaging both brakes when getting in and out of the chair. To keep the braking power optimal, you should regularly check the tyre pressure.

The extent to which the wheelchair user is able to cooperate determines how he or she should be lifted. Both active and passive transfers are possible with the Plus, if required with the aid of the care provider or using a lift.

n n Always engage the brake before transferring to or from the chair.

Forwards transfer 1. Fold up the footrests. Or fold away the legrests (if applicable). 2. Engage the wheelchair brake

Sideways transfer Remove the sides and armrests, if required.

Negotiating obstacles with an accompanying person

n n Push with your foot on the step tube and push down on the push-handles. n n Push the wheelchair onto the obstacle and remove your foot from the step tube. n n Push the wheelchair further and lift the rear wheels over the obstacle using the push-handles.

You can mount a kerb forwards, but it is better to descend backwards.

n n Keep your speed under control on gentle slopes.

Stairs · Kerb · Slope

Page 10 of the Life-Mobility Plus user manual — Maintenance
Page 10 · click to enlarge
Page 10

Maintenance

Technical problems

Minor maintenance (every two weeks) You can do minor maintenance on the Plus yourself. Clean your wheelchair with a damp cloth, water and an all-purpose cleaner. Note:

In the unlikely event that you experience technical problems with your wheelchair, please contact your dealer. The dealer will decide whether he can repair the chair or whether it will have to be returned to the factory. You may be able to solve some problems yourself.

n n Never use abrasive and aggressive cleaning agents or solvents including thinner, dry cleaning fluid or similar.

Movable components such as the push-handle, height-adjustable armrest, legrest and sides get stuck:

n n These components can become jammed in the frame if too much pressure is exerted on them. Carefully tap the components loose with a plastic hammer.

Check that all fastenings are secure. Tighten if neces- sary.

n n Over-tightening the screws can damage the wheelchair.

The brakes have insufficient braking power or do not brake with the same braking power on both sides:

n n Check the tyre pressure. n n You need the brakes to be adjusted, please consult your dealer.

Check the tyre pressure and condition of the tyres (ageing) regularly. Soft tyres make the wheelchair more difficult to use as they increase rolling resistance. Use, if necessary, the valve nipple supplied with the wheelchair for pumping up the tyres (for example, when using a bicycle pump). The correct tyre pressure is shown on the tyres.

n n All repairs other than those described above must always be performed by an authorised dealer. Improper repairs may endanger your health. Furthermore, repairs carried out by unauthorised persons will invalidate the guarantee on your chair. Use your common sense and decide whether you are in a position to resolve technical problems on the wheelchair yourself. If in doubt, always consult your dealer. When adjusting and installing or removing parts, consult this manual and follow your dealer’s advice. Do not place the accompanying person or the wheelchair user in danger.

Major maintenance (annual) Your dealer will be happy to carry out the major maintenance of your wheelchair. You can then be sure that you will be getting the best possible use out of it. You should also consult your dealer if components need replacing.

Page 11 of the Life-Mobility Plus user manual — Guarantee
Page 11 · click to enlarge
Page 11

Guarantee

Disposal of the product and packaging

Terms and Conditions of Warranty The Life & Mobility products are made with care and are carefully inspected before leaving the factory. Should it emerge that a product does not meet expectations please contact the party where you purchased the product. Life & Mobility respects the laws and regulations that protect the consumer and that apply in the country in which the product is purchased.

Disposal of the product and packaging From the environmental viewpoint, we recommend disposing of the packaging and the wheelchair in such a way that the materials used can be efficiently recycled.

In the majority of cases, you can hand in your used wheelchair to your wheelchair dealer. If this is impossible, you can hand in the wheelchair at your local refuse collection location.

The guarantee does not cover faults caused by a failure to comply with instructions for use and maintenance, abnormal use, wear and tear, negligence, overloading, accidents caused by third parties, use of non-original components or faults the cause of which is not related to the product.

This guarantee supersedes any other guarantee either laid down in law or verbally notified, with the exception of any written guarantee provided by Life & Mobility.

Guarantees are only valid within the EU.

Ask about the Life-Mobility Plus

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Life-Mobility Plus

Be the first to ask — other owners or our team will answer.

Original document

Life-Mobility Plus manual PDF

51 pages·1.7 MB·Wheelchair·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…