Instruction/ maintenance manual of the product 225E Bolens
Go to page of 20
Front Tine Tiller Model Series 300 & 33 0 OPERA T OR’S MANU AL IMPOR T ANT : READ SAFETY RULES AND INSTRUCTIONS CAREF ULL Y MTD LLC, P .O . BO X 3611 31 CLEVELAND , OHIO 44136-001 9 Warning: Thi.
2 TABLE OF CONTENTS Cont ent P age Important Safe O peratio n Prac tices ................. ............. ............. ............. ........... 3 Assembl ing Your Till er .................. ................... ............. ............. ............
3 SECTION 1: IMPORTANT SAFE OPERATION PR ACTICES WARNING: This sy mbol points out impo rtant safety instruc tions whi ch, if not foll owed, co uld endange r the personal safety and/o r proper ty of yourse lf and other s. Read an d follow all in struct ions in this manual before attempt i ng to oper ate this mac hine.
4 9. Look down and behind and use c are when in reverse or pulling mac hine towards you. 10. Start the engine according to the instructions found in this manual and keep feet well away from the tines at all times. 11. After striking a foreign object, stop the engine, disconnect the spark plug wi re and ground against the engine.
5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: This operat or’s m anual cover s var ious m odels of tillers. The units il lustrat ed may var y slight ly from your uni t.
6 Check Cable Ad justment • With the clut ch lever disengage d, pull star ter rope slowly sev eral time s. The tine s should no t turn. If they tur n, th e cable is not adj usted properly . • To adjust the cable, loos en the nut near the top of the cable an d unscre w the cabl e to provid e additiona l s lack in wire .
7 Choke Lever The choke le ver i s located ne ar the thr ottle cont rol. It is used to enr ich the fuel mix ture when sta rting a cold engine . Starte r Handle The sta rter han dle is l ocated on the e ngine and is used to m anuall y star t the eng ine.
8 Controlling Speed And Tilling Depth Wheel Yoke Adjustment Place whe el yoke so that the wheel s are forw ard (nearest po int betwee n wheels and tines) for sha llow tilling , cultivat ing and trans port. Th e forward spee d will increa se. Turn yoke arou nd (farthe st point between wheels and tines) for deep tilling.
9 wor king wid th of t he m achi ne is 22 o r 24 i nches . Fo r cultiv ation, this may be re duced to 13 inc hes by removi ng the outer tines . Refer to the Adj ustment Sec tion. When layin g out pla nt rows, be sure t o allow enough width to permit cu ltivatio n between th e rows.
10 SECTION 6: MAINTAINI NG YOUR TILLER WARNING: Disconnect the spark plug wire and ground it against the en gine before per forming any repairs or maintenance. Engine Refer to the se parate engi ne manua l for engin e maintenan ce i nstr uctions. Maintain engine oil as i nstru cted i n the sepa rate engine m anual packe d with your unit.
11 Fig ure 12 Off-Season Storage If the tiller wil l not be used for a period lo nger than 30 days, the following steps should be taken t o prepar e the tiller for s torage. • Clean t he exter ior o f engine and the e ntire ti ller thorough ly. L ubricat e the ti ller as d escrib ed in t he lubric ation in structi ons.
12 SECTION 7: TROUBLESHOOTING NOTE: For repair s bey ond th e minor adjus tments l isted a bove, c ontact y our ne arest s ervice deale r. Problem Cau se Rem edy Engine fail s to s tart 1. Spark p lug wi re dis connec ted. 2. Fuel tank emp ty or stale fuel .
13 SECTION 8: NOTES.
14 Model Series 300 & 330 1 2 3 4 5 6 7 8 5 6 9 10 11 12 13 5 14 14 15 16 17 18 19 20 21 22 23 24 14 10 9 10 25 10 26 27 28 29 30 31 32 33 34 35 36 37 38 39 34 40 41 42 43 44 45 46 47 48 49 50 51 .
15 Model Series 300 & 330 Ref . No. P art No. P ar t Description 1. 720-0 274 Gri p 2. 731-0 473 Clut ch Gr ip 3. 686-0 002 Clut ch L ev er 4. 649- 0137 Handl e Assemb ly 5. 712- 0442 Lock Nut Cap 1/4 -20 6. 738-122 5 Sh oul der Scre w 7. 74 6-1 148 Clut ch Cab le 8.
16 Model Series 300 1 2 3 1 2 4 5 6 7 8 9 10 11 6 12 13 14 15 16 20 17 4 15 16 18 18 10 19.
17 Model Series 300 Ref . No. P art No. P ar t Description 1. 734- 1988 Wheel 7 x 1.8 2. 738-092 9 Shoulder Scre w 3. 686-008 1A Wheel Bra cket Ass embly 4. 71 4-0 149 B Cot ter Pi n 5. 71 1-0415 Clev is Pin 6. 736-024 2 Bell W asher .340 ID x .872 OD 7.
18 Model Series 330 1 3 1 2 2 4 9 5 6 7 8 10 10 11 13 14 6 12 15 16 4 5 17 18 19.
19 Model Series 330 Ref . No. P art No. P ar t Description 1. 734- 1781 Wheel 8 x 1.75 2. 738-092 9 Shoulder Scre w 3. 686-008 1A Wheel Bra cket Ass embly 4. 71 4-0 149 B Cot ter Pi n 5. 71 1-0415 Clev is Pin 6. 736-024 2 Bell W asher .340 ID x .872 OD 7.
MANUF ACTURER’S LIMITED W ARRAN TY FOR: The limi ted warra nty set forth below is given b y MTD LLC with respe ct to new m erchandise purchased an d used in the United S tates , its possessio ns and te rritories.
An important point after buying a device Bolens 225E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bolens 225E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bolens 225E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bolens 225E you will learn all the available features of the product, as well as information on its operation. The information that you get Bolens 225E will certainly help you make a decision on the purchase.
If you already are a holder of Bolens 225E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bolens 225E.
However, one of the most important roles played by the user manual is to help in solving problems with Bolens 225E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bolens 225E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
